• 한국음향학회지
• /
• 제18권7호
• /
• pp.56-66
• /
• 1999

일반 내연기관이나 산업용로, 로켓 엔진 등의 기본적인 형상이라고 할 수 있는 관형 연소기에서 발생하는 연소 소음은 열-음향 되먹임 현상에 의해 야기되는 형태가 지배적이며. 심할 경우 시스템의 파괴를 야기할 수도 있는 중요한 문제이다. 본 연구에서는 열-음향 진동중에서도 열-기인 음향 진동으로 분류될 수 있는 현상에 초점을 맞추어 유동장, 음향장 및 연소 반응을 수치적으로 해석하여 여러 주어진 조건에 따른 정상적인 해석뿐만 아니라 음압 수준이나 기본 주파수 예측과 같은 정량적인 결과 도출을 효과적으로 수행할 수 있는 수치적 기법의 개발을 목적으로 하였다. 다양한 당량비를 가진 혼합기에 대해 수치 해석을 수행한 결과 실험 측정치의 경향과 잘 일치할 뿐만 아니라 정량적인 면에서도 상당히 정확한 예측을 할 수 있음을 확인하였다.

• 한국해양공학회지
• /
• 제22권2호
• /
• pp.34-41
• /
• 2008

As a basic study for developing a forecasting/estimating system that predicts water quality changes when Deep Sea Water (DSW) drains to the ocean after using it, this study was carried out as follows: 1) numerical simulation of the present state at DSW developing region in the East sea using SWEM, 2) numerical prediction of water quality changes by effluent DSW, 3) analysis of influence degree 'With defined DEI (DSW effect index) at F station. On the whole, when DSW drained to the ocean, Chl-a, COD and water-temperature were decreased and DIN, DIP and DO were increased by effluent DSW, and Salinity was steady. According to analysis of influence degree, the influence degree of DIN was the highest and it was high in order of Chl-a, COD, Water-temperature, DO, DIP and Salinity. The influence degree classified by DSW effluent position was predicted that suiface outflow was lower than bottom outflow. Ad When DSW discharge increased 10 times, the influence degree increased about $5{\sim}14$ times.

• 한국소음진동공학회논문집
• /
• 제14권3호
• /
• pp.175-184
• /
• 2004

Ground-borne noise and vibration generated by underground transit system has been recognized as an important environmental problem. This study reviews several of the procedures that have been used to predict ground-borne vibration. The vibration responses are measured at three sites that have different soil qualities. The measured vibration levels are compared with the predicted results by previously used vibration level prediction models. There are some drawbacks to apply these prediction models to selected sites because most of the existing prediction models are primarily based on empirical data and all of them lack of analytical models for the mechanism of ground-borne vibration generation. radiation, and propagation. In this study a numerical method, which is based on explicit differential method, is used to compensate for the shortcomings of existing prediction models. Although numerically computed results are not quantitatively in good agreement with the measured results, the trends are comparable in the sense that vibration level does not decrease monotonically with distance. Also, the site with the deepest tunnel gives the highest vibration level.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.129-141
• /
• 2003

The precise prediction of ground displacement plays an important role in planning and constructing tunnels. In this study, an equation for predicting the surface and crown settlement is suggested by examining the theories of ground movement caused by tunnel excavation. From the 3D numerical modeling, the reinforcement effect of UAM (Umbrella Arch Method) is quantitatively analyzed with respect to deformation modulus and overburden. By using a regression technique for the numerical results, an equation for predicting the settlement is suggested.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2007년도 동계학술발표대회 논문집
• /
• pp.382-386
• /
• 2007

In this study, the qualitative prediction and evaluation of clean room being utilized for mass production of electrronic components have been performed with the help of flow simulation. Compared to the experimental analysis based on measurements of the number of particles, concentration of contaminants and flow characteristics, the numerical analysis used in this study is much cost-effective.

• 대한조선학회논문집
• /
• 제42권4호
• /
• pp.350-356
• /
• 2005

Prediction of green water loads acting on the bow deck is au essential part for the design of bow structures against the green water impact. Proper technique of the green water simulation is highly required for the prediction of green water loads. in this paper, the green water flow on bow deck is simulated by FDM(finite difference method). Using the results of green water simulation, impact load on bow deck is calculated. Also, experiments are carried out to compare with the numerical calculation. Through the comparisons between experimental results and numerical results, it is verified that the present numerical tool is adequate as a practical calculation tool for the green water problem.

• 한국해안해양공학회지
• /
• 제9권4호
• /
• pp.201-207
• /
• 1997

우리나라 동해안 대부분의 중소어항에서는 항내 및 항입구부의 매몰현상이 심각하여 항내수심을 유지하기 위해 거의 매년 준설을 실시하고 있으며, 항내매몰로 인해 수심이 낮아져 배가 전복되는 등 극심한 피해를 입고있어 적지 않은 사회문제로 까지 확대되고 있는 실정이다. 본 연구에서는 매몰현상이 비교적 심각한 동해안의 K항를 선정 하여 항내매몰에 관한, 현지관측 및 수치모형실험을 실시하였고, 실시 결과 현지상황과 잘 일치 되는 흐름상황 및 매몰현상이 발생하였음을 알 수 있었다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 추계 학술대회논문집
• /
• pp.183-186
• /
• 2005

We developed an upwind numerical formulation based on the eigenvalues of the approximate Jacobian matrix in order to solve the hyperbolic conservation laws governing the two-fluid two-phase flow models. We obtained eight analytic eigenvalues in the two dimensions that can be used for estimate of the wave speeds essential in constructing an upwind numerical method. Two-dimensional underwater cavitation in a flow past structural shapes or by underwater explosion can be solved using this method. We present quantitative prediction of cavitation for the water tunnel wall and airfoils that has both experimental data as well as numerical results by other numerical methods and models.

• 소성∙가공
• /
• 제14권3호
• /
• pp.224-232
• /
• 2005

The high-pressure die-casting is one of the most effective methods to produce a large amount of products in short cycle time. This process, however, has a problem that the gas porosity defect appears easily. The generation of gas porosity is known mainly due to the air entrapment during the injection stage. Most of numerical simulations for the molten metal flow pattern observations have done in the treating of one phase fluid flow but the gas-liquid interface is essentially multi- phase phenomenon. In this paper, the two-phase fluid flow numerical simulation methods have been adapted to predict the gas porosity generations in the molten metal. The accuracy and the usefulness of the new simulation module have been emphasized and verified through some comparison experiments.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.22-24
• /
• 2008

This paper presents a numerical model of internal flows in a lubricant supplying and scavenging flow path of an aero-engine lubrication system. The numerical model was built in the General Analysis Software of Aero-engine Lubrication System, GASLS, developed by Northwestern Polytechnical University. The lubricant flow flux, pressure and temperature distribution at steady state were calculated. GASLS is a general purpose computer program employed a 1-D steady state network algorithm for analyzing flowrates, pressures and temperatures in a complex flow network. All kinds of aero-engine lubrication systems can be divided into finite correlative typical elements and nodes from which the calculation network be developed in GASLS. Special emphasis is on how to use combined elements which is a type of typical elements to replace some complex components like bearing bores, accessory gearboxes or heat exchangers. This method can reduce network complexity and improve calculation efficiency. Final computational results show good agreement with experimental data.