• 동력기계공학회지
• /
• 제18권6호
• /
• pp.21-28
• /
• 2014

The studies of the spray characteristics for a CRDI engine had been advancing by many researchers, because the performance and exhaust emission were significantly affected with the spray characteristics. But most experiments of the studies would be done at low ambient pressure conditions under 2MPa. In this study, injection rates were measured with Zeuch's method at various ambient pressures to 5MPa and a constant injection pressure of 130MPa. On the same conditions, non-evaporating spray images were taken with a high speed camera and analyzed carefully with Adobe Photoshop CS3. Macroscopic spray characteristics and breakup processes in the spray could be found from the examined and analyzed data. The initial injection rate, penetration, angle, velocity and breakup of the spray were practically affected with a variation of the ambient pressure, but the injection start time and injection period were scarcely affected. As the ambient pressure was higher, the breakup of a high density droplet region in the spray was happened slowly and the main position of breakup was shifted from a front of the spray to a upstream around a nozzle. The results and techniques of spray visualization and injection rate measurement in this study would be practically effective to study a high pressure diesel spray for a CRDI.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.256-256
• /
• 2013

Carbon nanotubes (CNT) / polyvinylidene fluoride (PVDF) piezoelectric composite films for nanogenerator devices were fabricated by spray coating method. When the CNT/PVDF mixture solution passes through the spray nozzle with small diameter by the compressed nitrogen gas, electric charges are generated in the liquid by a triboelectric effect. Then randomly distributed ${\beta}$ phase PVDF film could be re-oriented by the electric field resulting from the accumulated electrical charges, and might be resulted in extremely one-directionally aligned ${\beta}$ phase PVDF film without additional electric field for poling. X-ray diffraction patterns were used to investigate crystal structure of the CNT/PVDF composite films. It was confirmed that they revealed extremely large portion of the ${\beta}$ phase PVDF crystalline in the film. Therefore we could obtain the poled CNT/PVDF piezoelectric composite films by the spray coating method without additional poling process. Charge accumulation and resulting electric field generation mechanism by spray coating method were shown in Fig. 1. The capacitance of the CNT/PVDF films increased by adding CNTs into the PVDF matrix, and finally saturated. However, the I-V curves didn't show any saturation effect in the CNT concentration range of 0~4 wt%. Therefore we can control the performance of the devices fabricated from the CNT/PVDF composite film by adjusting the current level resulted from the CNT concentration with the uniform capacitance value.

• 항공우주시스템공학회지
• /
• 제13권5호
• /
• pp.16-23
• /
• 2019

본 논문은 국방과학연구소 엔진 시험장에 설치된 페리스코프 시스템의 설계 및 해석에 대해 다루고 있다. 페리스코프 시스템은 엔진 후단, 디퓨저 상단에 설치되어 있는 잠망경 모양의 관측 시스템이며 엔진 후단 고온(2300 K)의 연소 생성물 등에 직접적으로 영향을 받아서 파손 위험이 높다. 따라서 1차원 열전달 계산 및 2차원, 3차원 CFD 해석을 통해 열유속 및 정온도 분포를 확인하고 이를 통해 냉각 성능을 검증하였다. 현재의 설계에서 페리스코프 시스템을 통해 화염 형상 및 노즐 제어, 배출 유동의 안정성을 가시적으로 확인 가능하다.

• 한국추진공학회지
• /
• 제4권4호
• /
• pp.1-8
• /
• 2000

본 연구에서는 아음속/초음속 이젝터 시스템의 효과적인 설계를 목적으로, 증기 보일러로부터 발생하는 파열증기를 1차 구동유체로 하는 축대칭 아음속/초음속 이젝터 유동을 실험하였다. 과열증기는 여러형태의 아음속/초음속 노즐에 의하여 이젝터 혼합부로 방출되도록 설계되었으며, 2차정체실 내부에 있는 대기 공기는 증기제트에 의하여 혼합부로 유입된다. 실험에서는 2차정체실의 진공성능을 조사하기 위하여 넓은 범위의 이젝터 자동압력비에 대하여 적용하였다. 본 연구의 결과로부터 이젝터목에서 혼한유동의 정압은 1차 노즐의 형태에 관계없이 이젝터 작동압력비의 함수만에 의하여 결정된다는 것을 알았다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.403-404
• /
• 2008

국가 우주개발 중장기 계획에 따라 수행중인 한국형우주발사체(KSLV-1) 개발사업 중 2단에 사용할 Kick Motor(이하 KM)는 작동고도가 약 300km이므로 진공의 환경과 유사하다. 고고도에서 작동하는 로켓은 성능을 최대한 향상시키기 위해서 노즐의 팽창비를 상대적으로 크게 설계하며, 동일한 로켓으로 지상에서 연소시험 할 경우 노즐에서 박리가 발생하여 정확한 추력을 예측할 수가 없다. 본 논문에서는 고고도에서 KM 추력성능을 입증하기 위하여 수행한 시험설비의 설계/구축과정과 그 결과를 다루고 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.173-179
• /
• 2012

본 논문에서는 부분 흡입형 초음속 터빈의 로터 블레이드에 ${\pm}15^{\circ}$의 스윕 각도를 적용하여 그에 의한 효과와 공력 특성을 살펴보기 위해 정상상태 유동해석과 비정상상태 유동해석을 동시에 수행하고 그 결과를 비교해 보았다. 3차원 Navier-Stokes 유동해석에는 상용 코드인 FLUENT 6.3 Parallel을 사용하였다. 모든 계산 케이스들에서 정상상태 유동해석에 비해 비정상상태의 경우가 손실이 더욱 크게 나오는 결과를 나타내었다. 후방스윕(BSW)모델은 기준모델(NSW)에 비해 팁 간극으로 빠져나가는 누설 손실량을 줄이는데 큰 효과가 있었고 비정상상태 유동 해석에서는 로터 출구면 정효율의 증가현상이 더욱 뚜렷하게 나타났다.

• 설비공학논문집
• /
• 제20권1호
• /
• pp.75-80
• /
• 2008

The objective of this research was to investigate the enhancement of heat transfer by mesh in water/air direct contact air conditioning system. Mesh is inserted as a turbulent promoter in front of the water injection nozzle. The heat transfer characteristics with and without mesh and the effect of the number of inserted mesh and mesh porosity size have been studied experimentally. Inserted mesh improves heat transfer efficiency compared to non~inserted mesh system and heat transfer efficiency increased as the number of mesh is increased. Meanwhile, heat transfer efficiency decreased as the porosity of the mesh is increased. With inserted mesh, inlet and outlet temperature difference of air increased more than 50%. Heat exchange time of water/air to reach the 100% humidity decreased less than 30%. This result shows inserted mesh can enhance the performance of the water/air direct contact air conditioning system.

• 한국추진공학회지
• /
• 제24권6호
• /
• pp.45-52
• /
• 2020

초소형 스마트탄의 개발을 위해 초소형 추진기관을 설계하고 그레인은 내부 형상의 제작 용이성을 고려하여 열가소성 추진제로 제작하였다. 추진기관의 성능분석을 위해 지상연소시험과 내탄도 해석이 수행되었다. 그리고 사수와 추진기관 간 안전거리 설계에 대한 기초자료를 획득하기 위하여 수치해석을 수행하였으며, 배기가스의 온도분포는 수치해석과 IR 카메라의 측정결과를 비교하여 분석되었다.

• International Journal of Advanced Culture Technology
• /
• 제10권3호
• /
• pp.295-306
• /
• 2022

The NOx removal performance of the SCR process depends on various factors such as catalytic factors (catalyst composition, shape, space velocity, etc.), temperature and flow rate distribution of the exhaust gas. Among them, the uniformity of the flow flowing into the catalyst bed plays the most important role. In this study, the flow characteristics in the SCR reactor in the design stage were simulated using a three-dimensional numerical analysis technique to confirm the uniformity of the airflow. Due to the limitation of the installation space, the shape of the inlet duct was compared with the two types of inlet duct shape because there were many curved sections of the inlet duct and the duct size margin was not large. The effect of inlet duct shape, guide vane or mixer installation, and venturi shape change on SCR reactor internal flow, airflow uniformity, and space utilization rate of ammonia concentration were studied. It was found that the uniformity of the airflow reaching the catalyst layer was greatly improved when an inlet duct with a shape that could suppress drift was applied and guide vanes were installed in the curved part of the inlet duct to properly distribute the process gas. In addition, the space utilization rate was greatly improved when the duct at the rear of the nozzle was applied as a venturi type rather than a mixer for uniform distribution of ammonia gas.

• 한국산업융합학회 논문집
• /
• 제26권3호
• /
• pp.455-462
• /
• 2023

In this study, an automatic spraying lubrication system was developed to maintain the cleanliness of the switchgear when detecting the movement of the track through the switchgear. To develop this system, an air tank, valve block, and spray nozzle were designed, and the safety was secured through the pressure test of the prototype after designing the air tank. Furthermore, the environmental aspect was considered by minimizing the use of lubricant by enabling the mixing of air and lubricant through the production of a valve using the Venturi principle. The performance evaluation was conducted by implementing (producing) the injection system, and the product developed in this study was deemed installable in actual switchgear. It is expected that the proposed system will enable the maintenance of the cleanliness of the track during switching and reduce faults and malfunctions caused by switchgear defects.