• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.12
• /
• pp.1024-1032
• /
• 2007

The flow characteristics with the impinging angles of defrost nozzle jet inside a commercial vehicle passenger compartment were investigated experimentally by using the two-dimensional duct-nozzle model. The shape of the nozzle contraction was designed according to the curved line of cubic equation to the vertical plan of the flow direction. The impinging angles, defined as the angle between nozzle axis and a vertical line to the windshield, were varied from the $0^{\circ}\;to\;80^{\circ}$. The mean velocity distributions, the half-widths, and the momentum distributions with the cases of both the free jet and the impinging jet onto the dummy windshield were measured. The impinging jet flows similarly with wall jet from $X/b_o=20$, and the impinging angle has an effect on the half-width of the impinging jet. The momentum distributions onto the windshield increased with the increase of impinging angle, and then their inflection point was observed around the impinging angle of $60^{\circ}$.

• Design & Manufacturing
• /
• v.13 no.3
• /
• pp.41-47
• /
• 2019

In conventional machining, the use of cutting fluid is essential to reduce cutting heat and to improve machining quality. However, to increase the performance of cutting fluids, various chemical components have been added. However, these chemical components during machining have a negative impact on the health of workers and cutting environment. In current machining, environment-friendly machining is conducted using MQL (minimum quantity lubrication) or cryogenic air spraying to minimize the harmful effects. In this study, the injection nozzle that can combined injecting minimum quantity lubrication(MQL) and cryogenic gas was designed and the shape optimization was performed by using computational fluid dynamics(CFD) and design of experiment(DOE). Performance verification was performed for the designed nozzle. The diameter of the sprayed fluid at a distance of 30 mm from the nozzle was analyzed to be 21 mm. It was also analyzed to lower the aerosol temperature to about 260~270K.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.2
• /
• pp.425-432
• /
• 2019

Molecular dynamics simulations were carried out to analyze the impact on turbine rotational power based on nozzle shapes. y varying two parameters, turbine rotational velocity w and initial velocities ($V_x,V_y$) for generating molecules, turbine rotation velocities of molecules in turbine entrance arc region and turbine exit arc region were calculated. Average momentums were calculated over two regions, respectively and the differences (AMD) were compared and analyzed. The optimal range of w values to enhance AMD was investigated over 4 different nozzle shapes used, and an excellent nozzle shape to achieve more turbine rotational power was drawn.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1132-1140
• /
• 1998

The disintegration process of initial spray from high-pressure swirl injector was investigated at different injection pressures. The transient breakup phenomena that were difficult to observe at high injection pressure were easily observed at the low injection pressure of 0.4MPa. The effect of fuel remained inside a nozzle hole volume on the penetration of initial spray was also investigated. The disintegration process of initial spray could be classified four regions: the formation of mushroom shape, the first collision, the second collision, and the development of spray, The liquid film of cup shape was particularly found in the second collision region, and the growth ratio of its length and width at low and high injection pressures were compared.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.18-21
• /
• 2011

In this study, basic research on the pressure control using driven pintle of modulatable thruster is presented. For this purpose, pintle thruster and pintle shape was developed. The actuator model was selected by calculating pintle load using Fluent software. Preliminary unsteady experimental results show that huge pressure oscillation is occurred as the pintle approach toward nozzle wall. From the preliminary experimental results, we could see possibility of pressure control of the modulatable thruster.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.35-40
• /
• 1987

The experimental study, using constant pressure injection system, is carried out to investigate the effect of the geometrical shape changes of the needle valve of the effective flow area, the spray angle and the Sauter's Mean Diameter according to needle valve lift for a pintle-type injection nozzle. The results are as follows: 1) With the increase of the needle valve lift, the effective flow area is increased, the spray angle is at first increased and later decreased, and the Sauter's Mean Diameter is decreased. 2) It is also shown that the spray angle is maximum at the rapidly increased region of the effective flow area.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.1
• /
• pp.85-96
• /
• 2003

For a design of rocket engine nozzle, chemical equilibrium analysis which shares the same numerical characteristics with frozen flow analysis can be used as an efficient design tool for predicting maximum thermodynamic performance of the nozzle. 10 this study, a chemical equilibrium flow analysis code was developed for the design of hydrocarbon fueled rocket engines. 10 oder to understand the thermochemical characteristics occurring in a nozzle through the expansion process, such as recombination of chemical components and the accompanying energy recovery, chemical equilibrium flow analysis was carried out for the KSR-III rocket engine nozzles together with frozen flow and non-equilibrium flow analyses. The performance evaluation based on the present KSR-III nozzle flow analyses has provided an understanding of the thermochemical process in the nozzle and additionally, it has confirmed that the newly designed nozzle shape modified to have a reduced exit area ratio is an adequate design for obtaining an increased ground thrust.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.33-45
• /
• 2019

In this study, numerical simulations were performed to investigate the steady-state characteristics of a symmetric pintle nozzle by varying the position of the pintle and the altitude. The pintle nozzle shape was used in a linear pintle nozzle that had been analyzed prior to the study, and the boundary conditions of the chamber were considered to be according to the propellant burn-back characteristics. A software was used to perform a verification analysis of the square nozzle, pintle nozzle, and high-altitude conditions with an appropriate analytical technique. The pintle position had three different nozzle throat area conditions-: fully closed, half open, and fully open, and the altitude was set at 0, 5, and 20 km. The study compared the thrust, pintle drive load, and static stability at each condition.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.11a
• /
• pp.173-174
• /
• 1994

• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.05a
• /
• pp.344.2-344
• /
• 2001