• Journal of Power System Engineering
• /
• v.5 no.2
• /
• pp.63-70
• /
• 2001

To obtain the optimal condition of heat treatment of wear-resistant alloy, hardness and Charpy V-notch test have been performed with Co-based Stellite No.4, No.6 and Tribaloy 800 alloys, following by heat treatment at the various conditions. Heat treatment at $1250^{\circ}C$ for 1 hours caused the as-casted Tribaloy 800 with FCC crystal structure to transform to HCP structure and lamellar eutectic structure was disappeared, which did not influence on the hardness. Aging at $800^{\circ}C$ for 20 hours, following by $1250^{\circ}C$ for 2 hours heat treatment has enhanced hardness significantly, which is due to the precipitation of large amounts of Laves-phase. The hardness of Stellite alloys was increased by the aging at $800^{\circ}C$ to 5 hours, and was nearly constant by the aging over 5 hours. The toughness of Stellite alloys was a few influenced by the aging treatment.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.5
• /
• pp.17-26
• /
• 2021

It is challenging to estimate the fatigue life of construction equipment consisting of a welded joint using field structure test owing to the uncertainty of the S-N curve. IIW recommends different S-N curves for various welded joint types. However, there is no way to define an appropriate curve considering complex design shape and strain gauge characteristics. This paper proposes an equivalent S-N curve method based on the relationship between IIW effective notch stress and virtual stress using finite element analysis. Moreover, a case study was conducted for the excavator fuel tank. The proposed method is expected to enhance accuracy and consistency in calculating the fatigue life for the welded structure of construction equipment.

• Smart Structures and Systems
• /
• v.4 no.3
• /
• pp.343-365
• /
• 2008

In this study, the frequency domain method which utilizes the evaluation of changes in the structural mode shape is adopted to identify regions which contain localized damages. Frequency response function (FRF) values corresponding to the modal frequency, analogous to the mode shape coefficients, are used since change in natural frequency of the system is usually insignificant for localized damage. This method requires only few sensors to obtain the dynamic response of the structure at specific locations to determine the FRF via fast-Fourier transform (FFT). Numerical examples of an aluminum plate, which includes damages of varying severity, locations and combinations of multiple locations, are presented to demonstrate the feasibility of the method. An experimental verification of the method is also done using an aluminum plate with two different degrees of damage, namely a half-through notch and a through notch. The inconsistency in attaining the FRF values for practical applications due to varying impact load may be overcome via statistical averaging, although large variations in the loading in terms of the contact duration should still be avoided. Nonetheless, this method needs special attention when the damages induce notable changes in the modal frequency, such as when the damages are of high severity or cover more extensive area or near the boundary where the support condition is modified. This is largely due to the significant decrease in the frequency term compared to the increase in the vibration amplitude. For practical reasons such as the use of limited number of sensors and to facilitate automation, extending the resolution of this method of identification may not be efficient. Hence, methods based on wave propagation can be employed as a complement on the isolated region to provide an accurate localization as well as to trace the geometry of the damage.

• Journal of Korean Neurosurgical Society
• /
• v.47 no.3
• /
• pp.174-179
• /
• 2010

Objective : Cricothyrotomy and tracheostomy are performed by physicians in various disciplines. It is important to know the comprehensive anatomy of the laryngotracheal region. Hemorrhage, esophageal injury, recurrent laryngeal nerve injury, pneumothorax, hemothorax, false passage of the tube and tracheal stenosis after decannulation are well known complications of the cricothyrotomy and tracheostomy. Cricothyrotomy and tracheostomy should be performed without complications and as quickly as possible with regards the patients' clinical condition. Methods : A total of 40 cadaver necks were dissected in this study. The trachea and larynx and the relationship between the trachea and larynx and the surrounding structures was investigated. The tracheal cartilages and annular ligaments were counted and the relationship between tracheal cartilages and the thyroid gland and vascular structures was investigated. We performed cricothyrotomy and tracheostomy in eleven cadavers while simulating intensive care unit conditions to determine the duration of those procedures. Results : There were 11 tracheal cartilages and 10 annular ligaments between the cricoid cartilage and sternal notch. The average length of trachea between the cricoid cartilage and the suprasternal notch was 6.9 to 8.2 cm. The cricothyroid muscle and cricothyroid ligament were observed and dissected and no vital anatomic structure detected. The average length and width of the cricothyroid ligament was 8 to 12 mm and 8 to 10 mm, respectively. There was a statistically significant difference between the surgical time required for cricothyrotomy and tracheostomy (p < 0.0001). Conclusion : Tracheostomy and cricothyrotomy have a low complication rate if the person performing the procedure has thorough knowledge of the neck anatomy. The choice of tracheostomy or cricothyrotomy to establish an airway depends on the patients' clinical condition, for instance; cricothyrotomy should be preferred in patients with cervicothoracal injury or dislocation who suffer from respiratory dysfunction. Furthermore; if a patient is under risk of hypoxia or anoxia due to a difficult airway, cricothyrotomy should be preferred rather than tracheostomy.

• Journal of Welding and Joining
• /
• v.3 no.1
• /
• pp.22-31
• /
• 1985

Hot straining embrittlement is one of the most important factors which cause the brittle fracture initiation even in the service temperature in the case of mild steel and high tensile steel. Therefore it is necessary to analyze thoroughly the hot straining embrittlement occurred in weld HAZ of the structural steels. The behaviors of plastic deformation and fracture toughness at the notch tip of the hot strained weld HAZ in structural steels (SB 41 KS, SA 588-Grade A ASTM) have been studied by the recrystallization technique and crack opening displacement (COD) test method. The obtained results are summarized as follows; 1. The plastic zone is formed at the notch tip of weld HAZ owing to nomotonic and cyclic hot stran, and the maximum plastic strain increases with the accumulated hot straining amounts. 2. The distribution of the effective strain at the plastic deformed zone in HAZ can be determined as follows; (.epsilon. over bar $_{p}$ )$_{\chi}$=.epsilon. over bar $_{cr}$ ( $R_{/chi}$/.chi.)$^{m}$ where, .epsilon. over bar $_{cr}$ : (SB 41; .epsilon. over bar $_{cr}$ = 0.2, SA 588; .epsilon. over bar $_{cr}$ = 0.1) 3. The embrittlement of weld HAZ in SB 41 and SA 588 is influenced by hot strain, and the degree of embrittlement becomes deeper with hot straining amounts. 4. The embrittlement of weld HAZ of SB 41 is not influenced by the hot straining amounts until .epsilon. over bar $_{max}$ = 0.36, $R_{\chi}$ = 0.065mm, however the embrittlement of structure in SA 588 is considerably influenced even by a small quantity of the hot straining amounts.s.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.761-767
• /
• 2012

In this paper, a novel ultra-wideband planar monopole antenna for the UHF communications and Digital-TV reception is proposed. The proposed antenna fed by a coplanar waveguide(CPW) is based on a triangular patch that has a broadband characteristic. To further increase the bandwidth of the triangular patch antenna, the top side of the regular triangular patch is loaded with a notch cut and each oblique side with a step. In addition, a slope is given to the ground plane of the CPW structure. Experimental results show that the -10 dB return loss bandwidth of the proposed antenna is 2,320 MHz from 480~2,800 MHz(5.83:1 bandwidth), which covers all the frequency bands of the various wireless communication systems and Digital TV broadcasting in the UHF band. Within the entire operating frequency range, the measured antenna gain in y-z plane(E-plane) varies from 3.01 to 4.71 dBi.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.4
• /
• pp.515-522
• /
• 2011

The purpose of this study was to evaluate the material characteristics of SHN400 steel, which is suitable as a steel material for building structures, using the experimental approach. For this purpose, the chemical composition test, tensile test, macro test, micro test, and charpy notch impact test were conducted with specimens taken from the highest, thickest, and commonly used H-beams for girder or beam members. Each test was conducted under the Korean Standard(KS) test conditions. All the test results satisfied the requirements of KS (KS D 3866) and the steel material for seismic design. The carbon equivalent value (Ceq), which is related to weldability, and the yield ratio, which is related to inelastic behavior, showed especially good results. Thus, SHN400 is definitely suitable as the steel material for building structures.

• Journal of the Korean Magnetics Society
• /
• v.26 no.1
• /
• pp.31-37
• /
• 2016

This study considered the reduction of the detent force of a permanent magnet linear synchronous generator (PMLSG). The PMLSG has a relatively large magnetic air gap. Thus, a slotted type of stator structure is generally employed. Furthermore, the detent force, which is caused by energy imbalances owing to the interaction between tooth-slot structures and the permanent magnets (PMs), must be minimized for start-up operation. Therefore, in this paper, the methods of auxiliary teeth and a notch in the teeth are applied to reduce the detent force.

• Journal of Genetic Medicine
• /
• v.18 no.2
• /
• pp.142-146
• /
• 2021

Alagille syndrome (AGS) is a rare autosomal dominant inherited disorder, with major clinical manifestations of bile duct paucity, cholestasis, cardiovascular anomaly, ophthalmic abnormalities, butterfly vertebrae, and dysmorphic facial appearance. It is caused by heterozygous mutations in JAG1 or NOTCH of the Notch signaling pathway presenting with variable phenotypic penetrance and involving multiple organ systems. The following case report describes a unique case of a 16-year-old female with AGS who presented with the primary complaint of renovascular hypertension. She had a medical history of ventricular septal defect and polycystic ovary syndrome. The patient had a dysmorphic facial appearance including frontal bossing, bulbous tip of the nose, a pointed chin with prognathism, and deeply set eyes with mild hypertelorism. Stenoocclusive changes of both renal arteries, celiac artery, lower part of the abdominal aorta, and left intracranial artery, along with absence of the left internal carotid artery were found on examination. Whole exome sequencing was performed and revealed a pathologic mutation of JAG1, leading to the diagnosis of AGS. Reverse phenotyping detected butterfly vertebrae and normal structure and function of the liver and gallbladder. While the representative symptom of AGS in most scenarios is a hepatic problem, in this case, the presenting clinical features were the vascular anomalies. Clinical manifestations of AGS are diverse, and this case demonstrates that renovascular hypertension might be in some cases a presenting symptom of AGS.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.1
• /
• pp.23-30
• /
• 2024

This paper dedcribes the design. verification, and analysis techniques for an advanced phased array antenna. When applying an active phased array antenna to an aircraft or missile, miniaturization of the array antenna and wide-angle beam steering characteristics can be unavoidable antenna design considerations. In particular, the active reflection coefficient characteristics when electronically steering a wide-angle beam is a design parameter that must be minimized in terms of system survival and system performance. As a radiator suitable for broadband characteristics and wide-angle beam steering, this paper designed an array structure using SFN and minimized the active reflection coefficient according to beam steering of up to 40° based on the spherical coordivate system angle. The bandwidth of the radiator was confirmed to be 3GHz based on active reflection in the Ka-band. In addition, the performance of the actually manufactured 8by8 array antenna wsa analyzed by measuring the single pattern of the radiator through a near-field test, mathematically synthesizing it, and predicting the Tx/TRx beam used in the seeker system.