• Journal of the Korean Geosynthetics Society
• /
• v.13 no.2
• /
• pp.1-10
• /
• 2014

In this study, two different types of dredged fill injection methods are introduced and filling experiments were conducted to analyze the impact of each technique to the distribution and deposition of dredged soil fill and how it influence the final tube shape. Two transparent plastic tubes were fabricated to observe the deposition behavior of the deposited fill material. Both tubes measured 4.0 meters in length (L) and has vinyl tube diameters (D) of 0.5m and 0.7m. T-type and I-type inlet system are also introduced in this paper. The influence of this inlet systems to the distribution and deposition behavior of dredged soil fill inside the vinyl tubes were observed during the experiment. After the sedimentation of the slurry mixture, the water on top of the soil sediments are removed and the slurry mixture was re-injected into the vinyl tube, this process was carried out repeatedly. The shape changes of the vinyl tube, e.g. the changes in both tube height and width, are constantly monitored after each slurry injection and water draining phases. Crater formation was observed in the case of I-Type inlet system and a non-uniform sediment distribution occurred. For the diffusion deposit of soil particles to long distance are minimal shape technique using the T-Type inlet system. Therefore the undrain filling height ratio ($H/D_0$) was found to be around 0.54 to 0.64 and the horizontal strain ratio ($W/D_0$) ranges from 1.45 to 1.54. The filling soil height is proportional to dredged-material filling phases, but, horizontal strain ratio is constant or inversely reduced so that the center of tube body is raised in the upward direction.

• Journal of Food Hygiene and Safety
• /
• v.26 no.1
• /
• pp.64-69
• /
• 2011

Steamed rice is usually used as an essential ingredient when Takju or Yakju is brewed in Korea. Alternatively, non-steamed rice can be used to keep thermolabile nutrients and fresh tastes richer in Takju or Yakju. In this study, therefore, the physicochemical properties (ethanol and sugar contents, pH, total acidities, and turbidities) and the fermentative microbial profiles (aerobic mesophillic bacteria (AMB), fungi, lactic acid bacteria (LAB), acetic acid bacteria (AAB), and Escherichia coli and coliforms) have been compared among 4 Takju and 1 Yakju samples brewed using steamed or non-steamed rice. Yakju brewed using non-steamed rice has approximately 2-3 times higher ethanol and sugar contents than other 4 Takjus brewed using steamed or non-steamed rice. The pH and total acidity values of all the 5 samples ranged 3.77-4.30 and 0.12-0.35, respectively. As for turbidities, Yakju brewed using nons-teamed rice was transparent, but other 4 Takjus were not. The AMB and fungal counts for Yakju brewed using nons-teamed rice were approximately $10^4$-fold less than those for 4 Takjus. The LAB counts for Takju and Yakju brewed using non-steamed rice were $10^3$-fold less than those for Takjus brewed using steamed rice. The AAB counts ranged $2-6\;log_{10}\;CFU/mL$ for all the 5 samples. E.coli and coliforms were not detected. Overall, there was no significant difference in microbial counts among 4 Takjus brewed using steamed or non-steamed rice, but Takju has higher microbial counts than Yakju. All the 5 samples were conclusively considered to be hygienically brewed and processed containing plenty of beneficial microorganisms.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.12
• /
• pp.909-914
• /
• 2013

CIGS is one of thin film solar cell and has been studied so much, because of the possibility of low price and high efficiency. Until now, co-evaporation and sputtering were typical method to prepare CIGS absorption layer, and a few company commercialized solar cell by these method. However, non-vacuum process which has been studied for long time has not been progressed, though the merit of low price. Especially, aerosol deposition method has not been reported, because it is difficult to prepare a large quantity of various CIGS powder. In this study, CIGS powder was synthesized by mechanochemical method and CIGS absorption layer was deposited by aerosol deposition method. The thickness of the CIGS layer was controlled by the number of deposition and the surface roughness of it was affected by the amount of flow gas. And, also, I-V curve of it appeared metallic property in the case of 'as deposition'. After heat treatment in Se-rich atmosphere, the electrical property of it changed to a semiconductor. CdS and transparent conduction layer were formed by a typical method on it for solar cell. The efficiency of cell was appeared 0.19%. Though the efficiency was low because of the disharmony in the after-process, it was conformed that CIGS solar cell could be prepared by aerosol deposition.

• Journal of the Society of Disaster Information
• /
• v.3 no.2
• /
• pp.55-78
• /
• 2007

Currently, the departments related to security and secretary service exist in 18 universities and 30 colleges in Korea in order to raise professional security and secretary personnel. Among the 18 four-year colleges in Korea, only two of them have the ethics course include in their curriculum. Also, among the 31 two-year colleges, only three of them have the ethics course included in their curriculum. Besides, as some private security and guardian companies were recently utilized in illegal actions of the rich and ruling class, contradicting their original purpose of existence, many people point out their downfall as a ?forced private army.? As a professional job, if security secretaries take advantage of the knowledge and top-secret technologies and use them for non-ethical purposes, the effect of the damage is far more serious than other fields of jobs. Therefore, taking this event as a turning point, the contract contents and the task area between the client and the security and secretary company must become more transparent in order to prevent illegal actions, and also for the people working in the security and secretary service area, it is necessary to establish a firm ethical consciousness in order to behave appropriately in their working environment. Therefore, this study examines the proper direction of work ethics of the people working in the security and secretary service according to the professionalization of their field, and also aims to propose an appropriate work ethic system such that they will not become an unfortunate victim of various scandals anymore. To do so, the concept of work ethics in professional jobs was examined; and after the code of ethics that reflect the ethical value system of each professional job was reviewed, the study suggested a specific solution for establishing the codes of ethics for security and secretary service.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.235.2-235.2
• /
• 2015

The front transparent conductive oxide (TCO) films must exhibit good transparency, low resistivity and excellent light scattering properties for high efficiency amorphous silicon (a-Si) thin film solar cells. The light trapping phenomenon is limited due to non-uniform and low aspect ratio of the textured glass [1]. We present the low cost electrochemically deposited uniform zinc oxide (ZnO) nanorods with various aspect ratios for a-Si thin film solar cells. Since the major drawback of the electrochemically deposited ZnO nanorods was the high sheet resistance and low transmittance that was overcome by depositing the RF magnetron sputtered AZO films as a seed layer with various thicknesses [2]. The length and diameters of the ZnO nanorods was controlled by varying the deposition conditions. The length of ZnO nanorods were varied from 400 nm to $2{\mu}m$ while diameter was kept higher than 200 nm to obtain different aspect ratios. The uniform ZnO nanorods showed higher haze ratio as compared to the commercially available FTO films. We also observed that the scattering in the longer wavelength region was favored for the high aspect ratio of ZnO nanorods and much higher aspect ratios degraded the light scattering phenomenon. Therefore, we proposed our low cost and uniform ZnO nanorods for the high efficiency of thin film solar cells.

• Journal of the Korea Convergence Society
• /
• v.6 no.3
• /
• pp.103-109
• /
• 2015

TOLED(Transparent, Organic Light Emitting Diodes) based edutainment system has been studied to solve the actual feeling training and educational experience problem of e-learning. However, edutainment system using TOLED has a problem for the non-detection of multi marker array and rotate marker array, and it has problem for the dissonance phenomena caused by Illumination Environment between real world and virtual object. It also has a do not provide services through a variety of devices problem. Therefore, in this paper, we designed a system that provides a realistic actual feeling edutainment contents by recognizes the marker array rotation and a plurality of marker arrangement via an improved marker detection technique. And to unify the real space and virtual space of the lighting environment through a nested block layer.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.695-698
• /
• 2007

The control of electrical appliances residing in the home network can be accomplished via Internet with the UPnP expansion without modifying an existing UPnP. In this paper, we propose the Internet Gateway that consists of an UPnP IGD(Internet Gateway Device) DCP(Device Control Protocol) and an UPnP Bridge as a system to control electrical appliances of home network. UPnP IGD DCP is to enable the configurable initiation and sharing of Internet connections as well as assuring advanced connection-management features and management of host configuration service. It also supports transparent Internet access by non-UPnP-certified devices. UPnP Bridge searches for local home network devices by sending control messages, while control point of UPnP Bridge looks up devices of interest on the Internet, subsequently furnishing the inter-networking controlling among devices which belong to different home network systems. With our approach, devices on one home network can control home electrical appliances on the other hone network via Internet through IGD DCP with control commands of UPnP.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.1-7
• /
• 1999

This paper describes the modification of hull bottom for the air lubrication technique to the passenger boat in service at the Chung-Ju lake, which has a large beam-draft ratio. From numerical analysis of 2-D cavity problem by potential theory, the cavity shape, length and the pressure in cavity are estimated for the simplified geometry of hull bottom, and the non-dimensional parameters affecting air cavity phenomena are investigated. Extensive resistance tests for the model ship which has variation of step height and side strip have been performed to investigate the formation of air cavity and the drag reduction effectiveness. And also, the development of attached cavity to the bottom were observed from the flat bottom made by transparent acrylic plate. From this survey on the modification of bottom shape and the air lubrication technique, the total resistance of model ship could be reduced by about 25% at the design speed compared to the proto type hull form.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.42.2-42.2
• /
• 2011

$TiO_2$ films were modified by adding a glass frit as a light scattering particle and applied to an anode electrode in dye-sensitized solar cells (DSSCs) to enhance the adhesion between $TiO_2$ and fluorine doped transparent oxide (FTO). Low melting point glass frits at contents of (3 to 7wt%) were added to the nano crystalline $TiO_2$ films. The light scattering properties, photovoltaic properties and microstructures of the photo electrodes were examined to determine the role of the low glass transition temperature ($T_g$) glass frit. Electrochemical impedance spectroscopy, Brunauer-Emmett-Teller method and scratch test were conducted to support the results. The DSSC with the $TiO_2$ film containing 3wt% low Tg glass frit showed optimal performance (5.1%, energy conversion efficiency) compared to the $TiO_2$-based one. The photocurrent density slightly decreased by adding 3wt% of the frit due to its large size and non conductivity. However, the decrease of current density followed by the decrease of electron transfer due to the large frit in $TiO_2$ electrode was compensated by the scattering effect, high surface area and reduced the electron transfer impedance at the electrolyte-dye-$TiO_2$ interface. The stability of the photo electrodes was improved by the frit, which chemically promoted the sintering of $TiO_2$ at relatively low temperature ($450^{\circ}C$).

• Journal of Periodontal and Implant Science
• /
• v.48 no.2
• /
• pp.84-91
• /
• 2018

Purpose: The purpose of this study was to visualize and identify peri-implant bone defects in optical coherence tomography (OCT) images and to obtain quantitative measurements of the defect depth. Methods: Dehiscence defects were intentionally formed in porcine mandibles and implants were simultaneously placed without flap elevation. Only the threads of the fixture could be seen at the bone defect site in the OCT images, so the depth of the peri-implant bone defect could be measured through the length of the visible threads. To analyze the reliability of the OCT measurements, the flaps were elevated and the depth of the dehiscence defects was measured with a digital caliper. Results: The average defect depth measured by a digital caliper was $4.88{\pm}1.28mm$, and the corresponding OCT measurement was $5.11{\pm}1.33mm$. Very thin bone areas that were sufficiently transparent in the coronal portion were penetrated by the optical beam in OCT imaging and regarded as bone loss. The intraclass correlation coefficient between the 2 methods was high, with a 95% confidence interval (CI) close to 1. In the Bland-Altman analysis, most measured values were within the threshold of the 95% CI, suggesting close agreement of the OCT measurements with the caliper measurements. Conclusions: OCT images can be used to visualize the peri-implant bone level and to identify bone defects. The potential of quantitative non-invasive measurements of the amount of bone loss was also confirmed.