• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1385-1387
• /
• 1998

In this paper, we studied the electro-optical(EO) performance of photo-aligned twisted nematic(TN)-liquid crystal display(LCD) with oblique non-polarized ultraviolet (UV) light irradiation on polyimide (PI) surface. The monodomain alignment of photo-aligned TN-LCD is obtained with an angle of incidence of $85^{\circ}$ on PI surface. Also, we observed that the voltage transmittance and response time characteristics of photo-aligned TN-LCD is almost same compared to rubbing treated TN-LCD. Finally, we measured that the voltage-holding-ratio(VHR) of photo-aligned TN-LCD is almost same compared to rubbing treated TN-LCD.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.398-398
• /
• 2007

The Liquid Crystal (LC) alignment uniformity is very important in LC devices. The alignment mechanism of LC molecules on a rubbed polyimide (PI) surface is very important for both LC fundamental research and application. So, Generally a rubbing method to align LC has been widely used to mass-produce LCD panels. But because rubbing method is contact method between rubbing fabric and indium-tin-oxide glass or flexible substrate, rubbing method has some defects, such as the electrode charges and the creation of contaminating particles. Thus we strongly recommend a non-contact alignment technique for getting rid of some defects of rubbing method. Most recently, the LC aligning capabilities achieved by ion-beam exposure on the organic and nonorganic thin film surface have been reported successfully. In this research, we studied the tilt angle generation and electro-optical performances for a NLC on homeotropic polyimide surfaces with ion-beam exposure. The LC aligning capabilities of a nematic liquid crystal (NLC) on a homeotropic PI surface using a new ion-beam method were studied. On the homeotropic PI surface, the tilt angle of the NLC by exposure ion-beam had a tendency to decrease as increased ion-beam energy density. And, on the homeotropic PI surface, the alignment character of the NLC with respect to ion-beam energy was good. And we achieved satisfactory result for EO character.

• Tribology and Lubricants
• /
• v.22 no.3
• /
• pp.119-126
• /
• 2006

In this paper, the contact behavior characteristics of a primary sealing components such as a seal ring and a seal seat has been presented for a small hydro-power turbine. Using the non-linear FEM analysis, the maximum temperature, the axial displacement, radial differences between a seal ring and a seal seat, and maximum contact normal stress have been analyzed for three optimized sealing profiles in which are designed based on the FEM analysis and Taguchi's experimental method. The three primary sealing profiles between a seal ring and a seal seat are strongly related to a leakage of a water for a hydro-power turbine and wear of a primary sealing component. The computed results show that the contact rubbing area between a seal ring and a seal seat is very important for reducing a friction heating and wear in a sealing gap, and increasing a contact normal stress in primary sealing components. Based on the FEM computation, models II and III in which have a small rubbing surface of seal rings show low dilatation of primary sealing components, and high normal contact stress between a seal ring and a seal seat. Thus, the FEM computed results recommend a short contacting width of a primary sealing component for reducing a leakage and thermal distortions, and expanding a seal life. This means that a conventional primary sealing component may be switched to a reduced sealing face of seal rings.

• Tribology and Lubricants
• /
• v.20 no.6
• /
• pp.314-321
• /
• 2004

Thermal distortion of non-contacting mechanical seals with inclined rubbing surfaces is affected by friction heat between seal ring and seal seat. The circulation fluid along the inclined rubbing surfaces maintains cooling friction heat and lubrication between the sealing surfaces of mechanical seal with an inclined surface. Mechanical seals with inclined sealing surfaces may be useful for reducing the frictional heating and power loss because of the introduction of cooling fluids to the sealing gap between seal ring and seal seat. From the FEM computed result shows that the thermal behavior and von Mises stress of sealing faces with an inclined angle 60 are much reduced in comparison of the conventional mechanical face seal with rectangular sealing surfaces.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.180-182
• /
• 1996

In this study, we have investigated the characteristics of the response time and the viewing angle on twisted nematic (TN)-liquid crystal display (LCD) and amorphous (a) TN-LCD without rubbing. To measure the transmission-voltage, response time, and viewing angle characteristics, we prepared three kinds of LC cells and then studied the surface liquid crystal alignment effect. We studied that the response time on a-TN-LCD is fast compared to the TN-LCD. We suggest that the weak anchoring strength is attributed to the fast response time on a-TN-LCD. Also, we obtained the uniform viewing angle characteristics on a-TN-LCD. From these results, we consider that the liquid crystal alignment on LCD device are very important factor for electro-optical characteristics.

• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.15-19
• /
• 1997

The characteristics of the response time and the viewing angle on twisted nematic (TN) liquid crystal display (LCD) and amorphous (a)-TN-LCD without rubbing were investigated. To measure the tansmission-voltage, response time, and viewing angle characteristics, we prepared three kinds of LC cells and then studied the surface liquid crystal alignment effect. It was found that the response time on A-TN-LCD was fast compared to the TN-I-CD, and the weak anchoring strength was attributed to the fast response time on a-TN-LCD. Also, we obtained the wide viewing angle characteristics on a-TN-LCD. The liquid crystal alignment of LCD device for electro-optical characteristics is discussed in the present paper.

• Electrical & Electronic Materials
• /
• v.9 no.7
• /
• pp.733-744
• /
• 1996

본 논문에서는 최근 LCD소자에 있어서 큰 이슈로 등장한 표면 액정배향기술 및 광시야각 기술에 관하여 설명하였다. 표면 액정배향기술에 있어서는 종래의 러빙법에 대신하여 편광된 자외선을 조사하여 액정분자를 배열시키는 광배향제어법이 큰 기대를 모으고 있으며, 이 기술은 프리틸트 각 발생제어기술과 신뢰성이 과제로 남아있다. 광시야각 기술에 있어서는 최근까지 여러 방식이 제안되어왔으며 그 중에서도 현재로는 광학보상법, IPS방식 등이 실용화가 진행되고 있다. 그러나 향후 다른 방식의 기술발전 여부에 따라 상황이 변화될 것으로 예상된다. 각각의 방식에 따라 서로 장단점을 지니고 있어 향후 이용분야에 따라 용도를 나누어서 응용될 것으로 기대되어진다. LCD소자는 이러한 기술개발의 결과로 평판디스플레이 소자 중에서 더욱 확고한 위치를 확보할 것이며 더 많은 시장성을 점유할 것으로 전망된다. 이상으로 본 논문에서는 LCD소자의 표면액정 배향기술 및 광시야각 기술에 관하여 해설하였으며 표면액정 배향기술에 관하여는 간단히 소개하였으나 이 내용에 관하여는 다음 기회에 상세히 소개하기로 한다.

• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.52-60
• /
• 2013

Partially hydrolyzed cellulose acetate (CA) fibers were prepared by treating CA fibers in aqueous $Na_2CO_3$ solutions of various concentrations. The deacetylation of CA fibers was confirmed through FTIR spectra and WAXD patterns. The hydrolysis was confined to the surface part of the CA fiber by controlling the treatment conditions. The resultant fibers had a sheath-core structure with a sheath component of regenerated cellulose and a core of non-hydrolyzed cellulose acetate. The SEM images of the surface-hydrolyzed CA fibers, the core of which was dissolved out using acetone as the solvent, showed that the sheath thickness increased with increasing alkaline concentration, indicating an increase in the hydrolyzed fiber, i.e., regenerated cellulose. Polarized FTIR analysis of the polyimide film rubbed with velvet fabrics of surface-hydrolyzed CA fibers showed that polyimide molecules were preferentially oriented to the rubbing direction.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.513-514
• /
• 2008

The potential of non-rubbing technology for applying to display devices was demonstrated by irradiating a high density argon ion beam (IB) on a polyimide (PI) as a liquid crystal alignment layer. The superior electro-optical characteristics were obtained, compared to rubbed PI, Although the low pretilt angle was created on the IB irradiated PI.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.953-956
• /
• 2002

We successfully developed new photo-alignment materials which can be treated with linearly polarized UV (LPUV) light in near UV region. The alignment films were also shown to provide with surface anchoring as strong as that on rubbed polyimide when exposed to the LPUV light with warming up the substrate. It can be also able to control pretilt angle by introduction of alkyl side chain.