• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.1
• /
• pp.75-83
• /
• 2020

This study investigated the degradation characteristics and biodegradability of phenol, refractory organic matters, by injecting MgO and CaO-known to be catalyst materials for the ozonation process-into a Dielectric Barrier Discharge (DBD) plasma. MgO and CaO were injected at 0, 0.5, 1.0, and 2 g/L, and the pH was not adjusted separately to examine the optimal injection amounts of MgO and CaO. When MgO and CaO were injected, the phenol decomposition rate was increased, and the reaction time was found to decrease by 2.1 to 2.6 times. In addition, during CaO injection, intermediate products combined with Ca²⁺ to cause precipitation, which increased the COD (chemical oxygen demand) removal rate by approximately 2.4 times. The biodegradability of plasma treated water increased with increase in the phenol decomposition rate and increased as the amount of the generated intermediate products increased. The biodegradability was the highest in the plasma reaction with MgO injection as compared to when the DBD plasma pH was adjusted. Thus, it was found that a DBD plasma can degrade non-biodegradable phenols and increase biodegradability.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.619-623
• /
• 1998

The influences of reaction temperature, HF/DCM mole ratio, contact time and catalyst type on activity and selectivity of difluoromethane synthesis via hydrofluoriation of dichloromethane over fluorinated catalyst have been studied. It has been found that fluorinated $Cr/Al_2O_3$ catalysts, show better performance compared to pure fluorinated $Al_2O_3$ catalyst and then, non-treated catalysts demonstrate better than catalysts pretreated with hydrogen and air. The results show that the optimum reaction conditions are found as follows : reaction temperature at $340^{\circ}C$, mole ratio of HF/DCM 5 or above and contact time 20 sec. or above. With these conditions the maximum attainable yield of difluoromethane has been found to be greater than 80%. In particular, the activity and the selectivity of difluoromethane do not change with the reaction time on stream up to 8 hours.

• Journal of Environmental Science International
• /
• v.28 no.11
• /
• pp.983-991
• /
• 2019

This study investigated the use of a hydroxyl-radicals-generated microbubble/catalyst (MB/Cat) system for removing organic pollutants, nitrogen, and phosphorous from liquid fertilizer produced by livestock wastewater treatment. Use of the MB/Cat system aims to improve the quality of liquid fertilizer by removing pollutants originally found in the wastewater. In addition, a reduction effect has been reported for antibiotics classified as representative non-biodegradable matter. Samples of liquid fertilizer produced by an aerobic biological reactor for swine wastewater treatment were first analyzed for initial concentrations of pollutants and antibiotics. When the MB/Cat system was applied to the liquid fertilizer, TCOD, TOC, $BOD_5$, and $NH_3-N$, and $PO_4-P$ removal efficiencies were found to be approximately 52%, 51%, 30%, 21%, and 66%, respectively. Additionally, Amoxicillin hydrate was removed by 10%, and Chlortetracycline HCl and Florfenicol were not present at detectable levels These findings confirm that the MB/Cat system can be used with livestock wastewater treatment to improve liquid fertilizer quality and to process wastewater that is safe for agricultural re-use.

• Ceramist
• /
• v.21 no.4
• /
• pp.388-405
• /
• 2018

In this paper, we review about current development of electrode materials for Li-ion batteries and catalysts for fuel cells. We scrutinized various electrode materials for cathode and anode in Li-ion batteries, which include the materials currently being used in the industry and candidates with high energy density. While layered, spinel, olivine, and rock-salt type inorganic electrode materials were introduced as the cathode materials, the Li metal, graphite, Li-alloying metal, and oxide compound have been discussed for the application to the anode materials. In the development of fuel cell catalysts, the catalyst structures classified according to the catalyst composition and surface structure, such as Pt-based metal nanoparticles, non-Pt catalysts, and carbon-based materials, were discussed in detail. Moreover, various support materials used to maximize the active surface area of fuel cell catalysts were explained. New electrode materials and catalysts with both high electrochemical performance and stability can be developed based on the thorough understanding of earlier studied electrode materials and catalysts.

• Advances in environmental research
• /
• v.3 no.2
• /
• pp.151-162
• /
• 2014

Among the combination of 4 different second metals and 3 different noble metals, Ni 10%-Pd 1%/hematite (Ni(10)-Pd(1)/H) showed best tetrachloroethylene (PCE) removal (75.8%) and production of non-toxic products (39.8%) in closed batch reactors under an anaerobic condition. The effect of environmental factors (pH, contents of Ni and Pd in catalyst, and hydrogen gas concentration) on the reductive dechlorination of PCE by Pd-Ni/hematite catalysts was investigated. PCE was degraded less at the condition of Ni(5)/H (13.7%) than at the same condition with Ni(10)/H (20.6%). Removals of PCE were rarely influenced by the experimental condition of different Pd amounts (Pd(1)/H and Pd(3)/H). Acidic to neutral pH conditions were favorable to the degradation of PCE, compared to the alkaline condition (pH 10). Increasing Ni contents from 1 to 10% increased the PCE removal to 89.8% in 6 hr. However, the removal decreased to 74.2% at Ni content of 20%. Meanwhile, increasing Pd contents to 6% showed no difference in PCE removal at Pd content of more than 1%. Increasing H2 concentration increased the removal of PCE until 4% H2 which was maximumly applied in this study. Chlorinated products such as trichloroethylene, 1,1-dichloroethylene, cis-1,2-dichloroethylene, trans-1,2-dichloroethylene, and vinyl chloride were not observed while PCE was transformed to acetylene (24%), ethylene (5%), and ethane (11%) by Ni(10)-Pd(1)/H catalyst in 6hr.

• Journal of the Korean institute of surface engineering
• /
• v.55 no.3
• /
• pp.180-186
• /
• 2022

The production of hydrogen via water electrolysis (i.e., green hydrogen) using renewable energy is key to the development of a sustainable society. However, most current electrocatalysts are based on expensive precious metals and require the use of highly purified water in the electrolyte. We demonstrated the preparation of a non-precious metal catalyst based on CuCo₂O₄ (CCO) via simple electrodeposition. Further, an optimization process for electrodeposition potential, solution concentration and electrodeposition method was develop for a catalyst-substrate integrated electrode, which indicated the highly electrocatalytic performance of the material in electrochemical tests and when applied to an anion exchange membrane water electrolyzer.

• Journal of Energy Engineering
• /
• v.10 no.4
• /
• pp.370-378
• /
• 2001

Characteristics and synergistic effects of the coliquefaction of Alaskan subbituminous coal, wasted tire, and polypropylene were investigated in a tubing-bomb reactor at 41$0^{\circ}C$, and the coliquefaction reactions were performed at 37$0^{\circ}C$~45$0^{\circ}C$ to evaluate the coliquefaction mechanism. The coliquefaction kinetic model based on the free-radical theory was proposed and simulated by the non-linear parameter estimation method. Simulated results represented experimental ones successfully with the correlation coefficient of 0.99. When a catalyst was not used, the conversions were decreased as tetralin increase due to the decrease of liquefaction of polypropylene. When naphthenate catalysts of Mo, Co, and Fe were used, the coliquefaction conversions were increased with the increase of the liquefaction of polypropylene. When Co-naphthenate catalyst was used, the increase of the coliquefaction conversion were as high as 21~23%.

• Journal of Powder Materials
• /
• v.21 no.2
• /
• pp.119-123
• /
• 2014

Pt has been widely used as catalyst for fuel cell and exhausted gas clean systems due to its high catalytic activity. Recently, there have been researches on fabricating composite materials of Pt as a method of reducing the amount of Pt due to its high price. One of the approaches for saving Pt used as catalyst is a core shell structure consisting of Pt layer on the core of the non-noble metal. In this study, the synthesis of Pt shell was conducted on the surface of $TiO_2$ particle, a non-noble material, by applying ultraviolet (UV) irradiation. Anatase $TiO_2$ particles with the average size of 20~30 nm were immersed in the ethanol dissolved with Pt precursor of $H_2PtCl_6{\cdot}6H_2O$ and exposed to UV irradiation with the wavelength of 365 nm. It was confirmed that Pt nano-particles were formed on the surface of $TiO_2$ particles by photochemical reduction of Pt ion from the solution. The morphology of the synthesized Pt@$TiO_2$ nano-composite was examined by TEM (Transmission Electron Microscopy).

• Korean Chemical Engineering Research
• /
• v.53 no.6
• /
• pp.746-754
• /
• 2015

In this study, we investigated the effects of the temperature on the coal/biomass $char-CO_2$ gasification reaction under isothermal conditions of $700{\sim}900^{\circ}C$ using the lignite(Indonesia Eco coal) with biomass (korea cypress). Ni catalysts were impregnated on the coal by the ion-exchange method. Four kinetic models which are shrinking core model (SCM), volumetric reaction model (VRM), random pore model (RPM) and modified volumetric reaction model (MVRM) for gas-solid reaction were applied to the experimental data against the measured kinetic data. The Activation energy of Ni-coal/biomass, non-catalyst coal/biomass $Char-CO_2$ gasification was calculated from the Arrhenius equation.

• Journal of Electrochemical Science and Technology
• /
• v.9 no.3
• /
• pp.229-237
• /
• 2018

The electrochemical sensing performance of metal-graphene hybrid based sensor may be significantly decreased due to the dissolution and aggregation of metal catalyst during operation. For the first time, we developed a novel large-area high quality three dimensional graphene foam-incorporated gold nanoparticles (3D-GF@Au) via chemical vapor deposition method and employed as free-standing electrocatalysis for non-enzymatic electrochemical glucose detection. 3D-GF@Au based sensor is capable to detect glucose with a wide linear detection range of $2.5{\mu}M$ to 11.6 mM, remarkable low detection limit of $1{\mu}M$, high selectivity, and good stability. This was resulted from enhanced electrochemical active sites and charge transfer possibility due to the stable and uniform distribution of Au NPs along with the enhanced interactions between Au and GF. The obtained results indicated that 3D-GF@Au hybrid can be expected as a high quality candidate for non-enzymatic glucose sensor application.