• 공업화학
• /
• 제25권2호
• /
• pp.209-214
• /
• 2014

SDA (Solvent deasphalting)를 이용한 오일샌드 역청의 부분경질화 공정을 개발하기 위해 수행된 본 연구에서는 말텐에 대하여 포화탄화수소 용매의 종류, 용매 투입 비율, 온도, 전단속도 등에 따른 유변학적 거동과 비뉴톤 특성을 살펴보았다. 오일샌드 역청은 전단속도가 $50sec^{-1}$이고, 온도가 $25{\sim}85^{\circ}C$인 조건에서 $800{\sim}150000mPa{\cdot}s$의 겉보기 점도를 보이며, $35^{\circ}C$ 이하에서는 0.1~0.3 Pa의 항복응력을 나타냈다. 오일샌드와 말텐은 모두 Pseudoplastic의 특성을 보이고 포화탄화수소 용매의 탄소 수가 낮아질수록 말텐의 겉보기 점도는 감소하였다. 겉보기 점도와 온도와의 상관관계는 Guzman-Andrade식으로 나타낼 수 있었으며, n-Pentane의 투입 비율이 커짐에 따라 말텐의 점도가 감소하였다. 또한 온도가 높아질수록 말텐은 뉴톤 유체에 접근하였고, 용매로 사용된 포화탄화수소의 탄소 수가 작아질수록 비뉴톤 성질은 증가하였다.

• 문화기술의 융합
• /
• 제9권4호
• /
• pp.331-335
• /
• 2023

혈액의 점도가 높아질수록 혈액은 더 끈적하고 흐름이 어려워지므로 혈전의 발생 가능성이 높아져 허혈성 뇌경색의 발생 확률이 증가한다. 혈액 점도 측정은 최근 순환기계 질환의 예방을 위하여 그 중요성이 강조되고 있으며 혈액의 점도를 쉽고 정확하게 측정할 수 있는 점도계의 필요성이 대두되고 있다. 본 연구에서는 평행판 점도계 ARS-Medi에 의한 점도표준액과 인공혈액의 측정값들을 국제적으로 정확성과 신뢰성을 인정받는 TA instrument의 Ares-G2로 측정한 값들과 비교하였다.. 뉴턴성 용액인 N44 표준용액의 점도는 모든 전단율에서 두 기기 간에 거의 완벽하게 일치하였다, 비뉴턴성 용액인 인공혈액의 경우 가장 낮은 전단율인 1 rad/s 에서는 약 10%의 차이를 보였으나, 임상적으로 유의한 전단율인 10 rad/s 이상에서는 두 기기간의 측정값이 오차범위 내에서 모두 일치하였다. 우리는 새로 개발한 혈액 전용 평행판형 점도계 ARS-Medi가 1회용 평행판을 사용하므로 혈액 점도 측정의 편의성과 위생성이 향상되어 임상에 매우 유용할 것으로 기대한다.

• Journal of applied mathematics & informatics
• /
• 제25권1_2호
• /
• pp.51-66
• /
• 2007

A layer of compressible, rotating, elastica-viscous fluid heated & soluted from below is considered in the presence of vertical magnetic field to include the effect of Hall currents. Dispersion relation governing the effect of viscoelasticity, salinity gradient, rotation, magnetic field and Hall currents is derived. For the case of stationary convection, the Rivlin-Erickson fluid behaves like an ordinary Newtonian fluid. The compressibility, stable solute gradient, rotation and magnetic field postpone the onset of thermosolutal instability whereas Hall currents are found to hasten the onset of thermosolutal instability in the absence of rotation. In the presence of rotation, Hall currents postpone/hasten the onset of instability depending upon the value of wavenumbers. Again, the dispersion relation is analyzed numerically & the results depicted graphically. The stable solute gradient and magnetic field (and corresponding Hall currents) introduce oscillatory modes in the system which were non-existent in their absence. The case of overstability is discussed & sufficient conditions for non-existence of overstability are derived.

• Tribology and Lubricants
• /
• 제20권5호
• /
• pp.225-230
• /
• 2004

Most studies of elsatohydrodynamic lubrication are oriented only to the measurement of film thickness itself with optical interferometer. In order to exactly investigate the tribological characteristics of a certain lubricant, it is also important to get the information of traction behaviors as well. In this work, we developed a device for measuring the friction force of ehl contact condition as well as the film thickness. To verify the validity of the measuring system, the friction forces and film thicknesses under ehl condition are simultaneously measured with the variations of additive ratios of viscosity index improvers which cause non-linear tendencies of film thickness to contact velocity.

• Korea-Australia Rheology Journal
• /
• 제21권2호
• /
• pp.119-126
• /
• 2009

A numerical analysis is performed to investigate the effect of rotation on the blood flow characteristics with four different angular velocities. The artery has a cylindrical shape with 50% stenosis rate symmetrically distributed at the middle. Blood flow is considered a non-Newtonian fluid. Using the Carreau model, we apply the pulsatile velocity profile at the inlet boundary. The period of the heart beat is one second. In comparison with no-rotation case, the flow recirculation zone (FRZ) contracts and its duration is reduced in axially rotating artery. Also wall shear stress is larger after the FRZ disappears. Although the geometry of artery is axisymmetry, the spiral wave and asymmetric flow occur clearly at the small rotation rate. It is caused that the flow is influenced by the effects of the rotation and the stenosis at same time.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권7호
• /
• pp.779-784
• /
• 2005

This paper presents the theory of similarity transformations applied to the momentum and energy equations for laminar, forced, external boundary layer flow over a horizontal flat plate which leads to a set of non-linear, ordinary differential equations of phase change material slurry(PCM Slurry). The momentum and energy equation set numerically to obtain the non-dimensional velocity and temperature profiles in a laminar boundary layer are solved. The heat transfer characteristics of PCM slurry was numerically investigated with similar method. It is clarified that the similar solution method of Newtonian fluid can be used reasonably this type of PCM slurry which has low concentration. The data of local wall heat flux and convective heat transfer coefficient of PCM slurry are higher than those of water more than 150$\~$200$\%$, approximately.

• 대한수학회지
• /
• 제57권5호
• /
• pp.1079-1101
• /
• 2020

This work is concerned with a geometric inverse problem in fluid mechanics. The aim is to reconstruct an unknown obstacle immersed in a Newtonian and incompressible fluid flow from internal data. We assume that the fluid motion is governed by the Stokes-Brinkmann equations in the two dimensional case. We propose a simple and efficient reconstruction method based on the topological sensitivity concept. The geometric inverse problem is reformulated as a topology optimization one minimizing a least-square functional. The existence and stability of the optimization problem solution are discussed. A topological sensitivity analysis is derived with the help of a straightforward approach based on a penalization technique without using the classical truncation method. The theoretical results are exploited for building a non-iterative reconstruction algorithm. The unknown obstacle is reconstructed using a levelset curve of the topological gradient. The accuracy and the robustness of the proposed method are justified by some numerical examples.

• Korea-Australia Rheology Journal
• /
• 제21권4호
• /
• pp.289-297
• /
• 2009

We numerically analyzed flow characteristics of the polymer melt in the screw equipment using a proper modeling and investigated design parameters which have influence on the mixing performance as the capability of the screw equipment. We considered the non-Newtonian and non-isothermal flow in a single rotor equipment to investigate the mixing performance with respect to screw dimensions as shape parameter of the single rotor equipment and screw speed as process parameter. We used Bird-Carreau-Yasuda model as a viscous model of the polymer melt and the particle tracking method to investigate the mixing performance in the screw equipment and considered four mixing performance indexes: residence time distribution, deformation rate, total strain and particle standard deviation as a new mixing performance index. We compared these indexes to determine design parameters and object function. On basis of the analysis results, we carried out the optimal design by using the response surface method and design of experiments. In conclusion, the differences of results between the optimal value and numerical analysis are about 5.0%.

• Korea-Australia Rheology Journal
• /
• 제18권3호
• /
• pp.143-151
• /
• 2006

We analyzed the non-Newtonian and non-isothermal flow in a single screw extruder system and investigated the mixing performance with respect to the screw speed and the screw pitch. The viscosity of polymer melt was described with Carreau-Yasuda model. The mixing performance was computed numerically by tracking the motions of particles in the screw element system. The extent of mixing was characterized in terms of the deformation rate, the residence time distribution, and the strain. The results revealed that the high screw speed reduces the residence time but increases the deformation rate while the small screw pitch increases the residence time. It is concluded that the high screw speed increases the dispersive mixing performance and the small screw pitch increases the distributive mixing performance.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1995년도 추계학술대회 논문집
• /
• pp.64-67
• /
• 1995

Transfer Molding is currently the most widely used process for encapsulation integrated circuits(;IC). Although the process has been introduced over 20 years ago, generating billions of parts each year, it is far from being optimized. With each new mold, epoxy mold, epoxy mold compound, and lead-frame, lengthy period and expensive qualification runs have to be performed to minimized defects ranging from wire sweep, incomplete fill, and internal voids etc. This studies describes how simulation can be applied to transfer molding to yield acceptable design and processing parameter. The non-isothermal filling of non-newtonian reactive epoxy molding compound(;EMC) in a multi-cavity mold is analyzed. Sensitivity analysis is conducted to investigate the influence of process deviations on the final molded profile. This study trend is carried out by following some heuristic process guidelines.