• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.11-20
• /
• 2002

This paper describes the magnetic flux leakage(MFL) type non-destructive testing(NDT) system to detect the 3D defects on underground gas pipe. Magnetic systems with permanent magnets and yokes are analyzed by 3D non-lineal finite element method(FEM) with optimum design. In case of under-saturation of gas pipe, sensing signals are too weak to detect. In case of over-saturation, the changes of the sensing signals are too low to detect the defects sensitively. So, the operating points of the magnetic system are optimized to increase the changes of the MFL signals. The effects of the depth and size of the defects on the sensing signals are analyzed to define the range and resolution of the MFL sensors. To increase the sensor's sensitivity, the back-yoke sensors are introduced and tested.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.4
• /
• pp.491-497
• /
• 2010

The magnetic polishing is the useful method to finish some machinery fabrications by using magnetic power. This method is one of the precision techniques and has an aim for clean technology in the clean pipes. The magnetic abrasive polishing method is not so common in the field of machine that it is not known to widely. There are rarely researcher in this field because of non-effectiveness of magnetic abrasive. This paper deals with mediocritizing magnetic polishing device into regular lathe and this experiment was conducted in order to get the best surface roughness at low cost. This paper contains the result of experiment to acquire the best surface roughness, not using the high-cost polishing material in processing. In this paper, We could have investigated into the changes of the movement of magnetic abrasive grain. In reference to this result, we could have made the experiment which is set under the condition of the magnetic flux density, polishing velocity according to the form of magnetic brush.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.6
• /
• pp.265-272
• /
• 2008

In this paper, AC losses of long wire Bi-2223 tapes with different twist pitch of superconducting core were fabricated, measured and analyzed. These samples produced by a powder-in-tube method are multi-filamentary tape with Ag matrix. Also, it's produced by non-twist. The critical current measurement was carried out under the environment in Liquid nitrogen and in zero field by 4-prob method. And the Magnetic measurement was carried out under the environment of applied time-varying transport current by transport method. From experiment, the susceptibility measurements were conducted while cooling in a magnetic field. Flux loss measurements were conducted as a function of ramping rate, frequency and field direction. The AC flux loss increases as the twist-pitch of the tapes decreased, in agreement with the Norris Equation. Neutron-diffraction measurements have been carried out investigate the crystal structure, magnetic structures, and magnetic phase transitions in Bi-2223([Bi, Pb]:Sr:Ca:Cu:O).

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.99-100
• /
• 2015

Significant amount of bottom ash has been produced in the power plant located at southeast region of Korea, but those were abandoned in the pond site without any treatment. In these days, there is a strong move to enforce environmental regulations to protect surrounding nature, a lot of pressure is given to the power plant industry to remove hazardous chemicals from their waste material before landfill or site storage. The overall objective of this research is to separate hazardous chemicals from the bottom ash, and use it safely as sustainable construction material. In this specific study, magnetic separation of bottom ash was applied, and used as a fine aggregates to make mortar specimens. According to the results, it was found that the use of bottom ash decreased 28-day compressive strength. However, using non-magnetic bottom ash provides best results in terms of thermal conductivity, showing strong possibility to be used as heat insulating material.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.06a
• /
• pp.220-221
• /
• 2003

Equiatomic FePt and CoPt alloy thin films have received considerable attention as possible magnetic and magneto-optic recording because of their high magnetic anisotropy energy and high coercivity. The high coercivity in these thin films is due to the presence of finely dispersed ordered FePt phase mixed with disordered FePt phase. However, a high temperature treatment, either substrate heating during deposition or post annealing, is needed to obtain the ordered L1$\_$0/ phase with high value of magneto crystalline anisotropy. Recent microstructural studies on these films suggest that the average grain size ranges from 10-50 nm and the grains are magnetically coupled between each other. On the other hand, the ultrahigh-density magnetic recording media with low media noise imposes the need of a material, which consists of magnetically isolated grains with size below 10 nm. The magnetic grain isolation can be controlled by the amount of additional non-magnetic element in the system which determines the interparticle separation and therefore the interparticle interactions. Recently, much research work has been done on various non-magnetic matrices. Preliminary studies showed that the samples prepared in B$_2$O$_3$ and Carbon matrices have shown strong perpendicular anisotropy and fine grain size down to 4nm, which suggest these nanocomposite films are very promising and may lead to the realization of a magnetic medium capable of recording densities beyond 1 Tb/in$^2$. So, in this work, the effect of Carbon doping on the magnetic properties of FePt nanoparticles were investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.136-139
• /
• 1997

In this paper, we inveatigate frequency dependance of inductance effects of FeCoB amorphous magnetic films. First, amorphous magnetic film having near zero magnetostriction is the basic composition of (Fe$_{1-x}$ / $Co_{x}$)$_{79}$Si$_2$B$_{19}$ with x=0.94, 0.95 and in order to decrease magnetio . anisotropy, the film was annealed in 28$0^{\circ}C$/30min, 40$0^{\circ}C$/30min, 40$0^{\circ}C$/1hr with near crystallization temperature under non-magnetic field. As result of investigation, in case of x=7.95 than x=0.94, we could have obtained high values, which inductance ratios in the low frequency was 488%. And Quality factor Q was under 0.7 in all sample, in case of annealed in 28$0^{\circ}C$/30min, we could have obtained highest value, which x=0.9fl is about 0.62 in 400[kHz], and in case of x=0.95 was about 0.35 in 1[MHz].z].].

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2535-2537
• /
• 2000

In order to detect and monitor the broken cords of steel-cord belt from being damaged by impact of large lump of materials and the corrosion of steel cord, we developed a non-contact magnetic coil detection system. This measures the deterioration of reinforcing cables in steel cord conveyor belt which transport the ores in raw material plant. In this research, magnetic coil sensor of broken-cord detection system has exciting part and sensing part. The broken-cord detection system is operated by supplying a transmitter coil with electric power to generate magnetic field, and then the change of induced voltage is detected in each receiver coils due to resultant magnetic flux effected by the broken steel cords at the inside of the conveyor belt. By the informations such as the position and size of the broken steel cords obtained by SCBMS(Steel Cord Belt Monitoring System), it is expected that not only the span of belt life will be lengthened, but also this system can enable operators to plan scheduled maintenance and prevent the enlargement of damaged parts in steel cord belt at an early stage

• Journal of the Korean Magnetics Society
• /
• v.3 no.2
• /
• pp.108-114
• /
• 1993

This paper presents a study on the effects of silica coating in the production of ${\gamma}-Fe_{2}O_{3}$ powders suitable for magnetic recording media. Emphasis has been put on investigating the relationship between the powder characteristics and the effects of silica coating in the heat-treatment stage of ${\gamma}-Fe_{2}O_{3}$ production. After we prepared non-coated ${\gamma}-Fe_{2}O_{3}$ and silica coated ${\gamma}-Fe_{2}O_{3}$ with coating water glass on the surface of goethite and heattreatment process, we compared and investigated powder characteristics. As silica coated layer played a role of preventing the powders from overreduction to metal iron and rapid oxidation, silica coated ${\gamma}-Fe_{2}O_{3}$ showed superior magnetization value due to inhibiting t!1e adulteration of ${\alpha}-Fe_{2}O_{3}$ into the final product. When silica coated layer acted as a sintering restrainer, silica coated ${\gamma}-Fe_{2}O_{3}$ showed high coercivity and specific sur-face area due to good acicularity.

• Journal of Power System Engineering
• /
• v.8 no.3
• /
• pp.52-57
• /
• 2004

A new non-destructive inspection technique has been developed. One characteristic of the technique is that defects are visualized by laser ray. Magnetic domains and domain walls of a magneto-optical sensor(MO sensor) are varied by the magnetic flux leaked by defects, and the variations are observed by the reflected light of the laser ray. The information of defect can remotely be inspected by this technique in a real time. This paper describes the results estimated on the 2-dimensional surface defects and opposite-side defects in a ferromagnetic material and the natural surface defect in a clutch disk wheel. The light region of a visible image and the magnitude of a reflected light increases as the input current of the magnetizer increases. The natural surface defect, that has not the width of crack's open mouth, can be also visualized like as 2-dimensional artificial defects.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1555-1557
• /
• 1998

In order to investigate the core material for over-head transmission line with non-magnetic and high strength nitrogen steel, microstructure and several basic properties of Fe-Mn-Cr-Ni-N steel have been studied. It is necessary that core material have a $\gamma$ phase to have a non-magnetic characteristics. To acquire a $\gamma$ phase, Mn, Ni and C are added as a alloying element. It was found that Fe-25Mn-16Cr-1Ni-N alloy have a stable $\gamma$ phase. The precipitate from this alloy system was $(Cr, Fe)_7C_3$. High Mn and N steel satisfies Sievert's relation that solubility of nitrogen increases with the square root of partial pressure of gas in metal-gas system and the hardness have proportional relation with nitrogen concentration.