• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.946-949
• /
• 2005

In this paper, influence factors on dynamic properties of floor impact noise insulation materials are suggested. For this purpose measurements on the dynamic stiffness and the loss factor of resilient materials are carried out by Korea standard (KS F 2868) according to the change of density, thickness, design pattern, and composition of materials. As a result the values of dynamic stiffness was decreased at high density and thick thickness, and that of loss factor was increased at low density. For dynamic properties, the pattern of lattice and waffle type material is better than that of plat type, and the mixed composition of materials is better than the composition of double layer materials at same thickness.

• 한국군사과학기술학회지
• /
• 제21권6호
• /
• pp.790-798
• /
• 2018

Discrete noise signals from a small scale tactical unmanned aerial vehicle(UAV) propeller were predicted numerically using time domain approach. Two-bladed 29 inch propeller in diameter and 150 kgf in gross weight were used for main parameters of the UAV based on the actual size of the similar scale vehicle. Panel method and Farassat formula A1 were adopted for aerodynamic and aeroacoustic analysis respectively. Time domain signals of both thickness and loading noises were transformed into frequency domain to analyze the discrete noise characteristics. Directivity pattern in a plane perpendicular to the rotating disc plane and attenuation of noise intensity according to double distance were also presented.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.564-565
• /
• 2012

• 한국품질경영학회:학술대회논문집
• /
• 한국품질경영학회 2009년도 추계학술대회
• /
• pp.317-323
• /
• 2009

In this paper, we propose new methods which is to determine level of noise factor. Even Taguchi give level of noise factor which is best(or maximum) and worst(or minimum) condition, we give level of noise factor which is representative value by observing noise factor frequency. Sometimes level of noise factor is given one, two and three. We know this method is more fit in real fields.

• 품질경영학회지
• /
• 제37권4호
• /
• pp.10-15
• /
• 2009

In this paper, we propose new methods which is to determine level of noise factor. Even Taguchi give level of noise factor which is best(or maximum) and worst(or minimum) condition, we give level of noise factor which is representative value by observing noise factor frequency. Sometimes level of noise factor is given one, two and three. We know this method is more fit in real fields.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1391-1394
• /
• 2007

In order for Hypoid gear development. Gears are required to sustain heavy loads or on applications where the gear box is made or a material with a different coefficient of thermal expansion form that or the gears and shafts, it is desirable to make a deflection and contact check under load. The deflection test is performed in the actual gear mounting using completely processed gear. This test should cover the full operating range of gear loads from no load to peak load. Under peak load the contact pattern should extend to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface.

• The Journal of the Acoustical Society of Korea
• /
• 제24권2E호
• /
• pp.38-45
• /
• 2005

The noise reduction of the In-The-Ear (ITE) hearing aid (HA) can be achieved by arrays of microphones. Each of the right and the left ears was assumed to have two HA microphones. These arrays of HA microphones produce particular patterns of directivity by some time delay between two microphones. The directivity pattern geometrically increase the S/N ratio. The boundary element method (BEM) was used for the three dimensional simulation of the HA directivity pattern with the two pairs' microphone arrays. The separation between two microphones was fixed to 10 mm. The time delay between the two microphones was calculated to produce the most narrow directivity pattern in the fore front of the head. The variation of the time delay was examined in accordance with input frequencies. This numerical analysis may be then applied for the calculation of the time delay parameter of the digital hearing aid DSP chip.

• 한국군사과학기술학회지
• /
• 제10권3호
• /
• pp.43-50
• /
• 2007

A range-frequency interference pattern is analyzed in the course of the propagation of ship noise in shallow water. It has been shown to exhibit striated bands of intensity maxima and minima in the spectrogram. The slope of the striations is an invariant of the modal interference and is described by a waveguide invariant parameter $\beta$. It turns out that this interference pattern is useful for identifying the physical properties of the waveguide such as seabed properties. In this article, the interference pattern is analyzed using image processing techniques to produce the distribution of the beta and the effects of sediment types and geoacoustic parameters on beta distribution are examined and characterized by moments of the distributions.

• 한국소음진동공학회논문집
• /
• 제19권10호
• /
• pp.1012-1020
• /
• 2009

This research is focused on the experimental study of the noise induced by two-phase refrigerant flow in the evaporator. The two-phase flow in the evaporator has various flow patterns. The effects of two-phase flow pattern's characteristics on the noise of the evaporator are investigated experimentally. The experimental data shows that the generated noise is mainly related to the layout of the pipe and the certain two-phase flow patterns such as the churn and slug flow. Based on these results, we removed the unnecessary vertical pipe and changed the pipe diameter of the evaporator - inlet into small one in order to avoid the intermittent flow condition. The noise level of newly-designed inlet-pipe of the evaporator was measured experimentally by refrigerant-supplying equipment and compared with that of conventional one.

• 한국전자파학회논문지
• /
• 제18권5호
• /
• pp.539-546
• /
• 2007

본 논문에서는 온-칩 스파이럴 인덕터 해석에 대한 3차원 전자장 시뮬레이션 방법을 제시하였으며, 이 방법은 정확히 예측 가능한 CMOS VCO를 설계하는데 적용될 수 있음을 보였다. VCO는 CMOS 0.25 um 표준 공정을 이용하여 LC-공진형으로 구현하였으며, 공진기의 스파이럴 인덕터는 실리콘 기판과의 사이에 그라운드 패턴을 삽입한 경우와 그렇지 않은 경우에 대해 각각 VCO를 구현하여 인덕터의 Q값 개선에 의해 VCO의 위상 잡음이 어느 정도 개선되는지를 검증하였다. 제작된 VCO는 2.5 V 제어 전압에서 3.094 GHz, -12.15 dBm 출력을 가지며, LC 공진에 사용된 단일 인덕터의 Q는 그라운드 패턴을 삽입한 경우 3 GHz에서 8% 정도 개선됨을 시뮬레이션을 통해 검증하였으며, 이로 인한 위상 잡음은 3 MHz 오프셋 주파수에서 9 dB 개선되어짐을 실험을 통해 확인하였다.