• Proceedings of the Acoustical Society of Korea Conference
• /
• 1997.06a
• /
• pp.68-74
• /
• 1997

Ship radiated noise is an infortant parameter which dtermines Anti Submarine Warfare(ASW) countermeansure or passive Sonar detection and classification performance. Its measurement should be performed under controlled ocean acoustic environment. In data reduction of the measured data from hydrophone array, theeffect fo ambient noise, surface reflection and bottom reflection etc. should be compensated to obtain the source level of the ship radiated noise. This study describes the measurement hydrophone array design criteria based on the analysis of transimission anomaly due to the surface reflection.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.4
• /
• pp.396-402
• /
• 2014

The measurement of air-borne noise in a naval ship is a crucial element. Because the noise in a naval ship interferes with a communication between crews and finally it causes to reduce the combat power. Thus, most of newly built ships have to satisfy the criteria of air-borne noise in the stage of delivery of a naval ship. In order to evaluate success or failure of criteria, uncertainty of the measurement should be considered. This study introduces the test method for the measurement of the air-borne noise in a naval ship and is concerned with the evaluation of uncertainty. The uncertainty results which was from the measurement of air-borne noise in 7 naval ships newly built satisfy the error tolerance(2dB). Therefore, it is need to reduce the error tolerance for the reliable measurement result.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.6 s.99
• /
• pp.738-748
• /
• 2005

The ship radiated noise level fluctuates by the difference of interference and reverberation according to measurement methods and environmental conditions. These phenomena cause error of the source level estimation even in the same environment conditions. This paper describes a quantitative analysis and a reduction method for an error value to the source level estimation in spatial and temporal interference environment. The design criteria of the radiated noise measurement array composed of omni-directional hydrophones and the source level accuracy in the deep water range are given. The source level accuracy in the shallow water range is also derived based on the statistical model of the multiple reflection paths. The results are verified using the water tank experiment and the sea trial.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.782-788
• /
• 2008

In this paper, a comparison about two representative Transfer Path Analysis(TPA) methods for air-borne noise based on, matrix inversion method and pressure transmissibility, are presented on the view point of crosstalk effect between sources. In order to assess accuracy of two methods according to path models between virtual airborne noise sources, experiments are made for two cases, weak and strong crosstalk effect condition, by using acrylic vehicle model. Based on this assessment, the paper presents a reasonable application criteria for TPA method according to the circumstances of air-borne noise sources.

• Journal of Environmental Health Sciences
• /
• v.16 no.1
• /
• pp.9-19
• /
• 1990

To evaluate the degree of traffic noise at the main shopping districts, 30 sites, in Pusan and produce the basic data of traffic noise counterplan, this research was conducted. Noise rating methods utilized were Leq(equivalent continuous sound level), Lr (rating sound level) and TNI (traffic noise index). As the results, all sites passed beyond Korean Environmental Noise Standard 70 dB(A) in Leq and 46.7% sites fell under 'widespread complaints'step, 40.0% 'threat of community' action'step, 13.3% 'vigorous community action'step by Lr ratings, and 30.0% sites were over acceptable TNI criteria of 74. Therefore, traffic noise at Pusan shopping districts was very severe.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.849-854
• /
• 2001

A study on performance of the sound absorbing noise barrier is presented. Noise barrier of sound absorbing type is composed of the front panel, sound absorbing material, and back panel. For allowing sound path, front panel is usually perforated. The performance of the noise barrier is governed by the opening ratio of the perforated panel, sound absorption coefficient of the sound absorbing material. In this study, the effects of the opening ratio, diameter of the hole, thickness of the sound absorbing material are investigated. It is found that the thickness of the sound absorbing material must be at least 50 mm to ensure the required minimum NRC value 0.70, and the opening ratio is greater than 0.2. It is shown that the thickness of the back panel is crucial in providing required STL (Sound Transmission Loss) value. The performance of the developed noise barrier is measured, where its sound absorbing coefficient and sound transmission loss satisfy the criteria.

• ETRI Journal
• /
• v.45 no.2
• /
• pp.226-239
• /
• 2023

Challenges in cognitive radio and tactical communications include recognizing anonymously received signals and estimating parameters in a blind or semi-blind manner. In this paper, we examine this issue for orthogonal frequency division multiplexing (OFDM) signaling. There are several parameters in OFDM signaling, and the blind receiver must extract and consider the synchronization issue. We assume that the blind receiver is aware of modulation type, OFDM, and not aware of chip duration and the length of cyclic prefix. First, we present new criteria based on kurtosis to estimate these parameters and compare their performance at different levels of additive white Gaussian noise with methods based on correlation, kurtosis, maximum likelihood, and matched filter. Then, we perform synchronization and estimate the start time based on these criteria and several new criteria in two steps: fine and coarse synchronization. Finally, in a more practical setup, we present the idea of jointly estimating the mentioned parameters and the signal start time as coarse synchronization. We compare different criteria and show that one of the proposed criteria has the highest efficiency.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.11
• /
• pp.1021-1027
• /
• 2007

A construction noise is the main reason for people's petition among the pollution. The purpose of this study is to develop the noise prediction program to see the level of the noise on the construction site more accurately. For this purpose, the database of the power level on the various equipments was made. The noise reduction by distance and the noise reduction by diffraction of barrier were mainly considered and calculated. The simple noise prediction program will provide the information about proper height and length of the potable barrier which satisfies noise criteria of the construction sites from a construction planning stage. To investigate the reliability of this program, the predicted data was compared with the measured data. An average of difference between measured data and predicted data is $0.1{\sim}2.8\;dB(A)$ and a coefficient of correlation is about $0.85{\sim}0.95$.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.10 s.115
• /
• pp.1005-1013
• /
• 2006

A survey and auditory experiment on multiple residential noises such as floor impact, airborne, bathroom, drainage and traffic noises were conducted to develop a combined rating system and to establish criteria for multiple residential noises. Subjective reactions such as annoyance, activity disturbance, sleep disturbance, and satisfaction to overall noise environment and each residential noise were recorded. The effect of individual noise perception on the evaluation of the overall noise environment was also investigated. The survey results showed that satisfaction for floor impact noise most greatly affects the overall satisfaction for overall noise environment and annoyance most greatly affects the satisfaction for individual noise sources. Auditory experiments were undertaken to determine the percent satisfaction for individual noise levels. Result of auditory experiment showed that the noise level corresponding to 40 % satisfaction is 49 dB $(L_{i,Fmax,AW})$ for floor impact and is about 40 dB(A) for airborne, drainage and traffic noise. From the results of the survey and the auditory experiments, an equation for predicting the overall satisfaction for multiple noises was developed and a classification of multiple residential noises was proposed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.560-563
• /
• 1997

Sound intensity method is well known as a visualization technique of sound field and sound propagation in noise control. Sound intensity is a vector quantity that describes the magnitude and the direction of net flow of acoustic energy at a given position. The current measuring method is expensive and difficult to identify the noise source exactly. In this paper, we have studied the noise source identification and the characteristics of noise source of rotary compressor for air conditioner using complex sound intensity method. The new method for instantaneous sound intensity is also proposed and it is useful for transient state and steady state. The criteria of these states select auto correlation coefficient. The advantage, simplicity and economic attribution of this method are verified by analyzing the characteristics of noise source with instantaneous sound intensity compared to mean sound intensity.