• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.215-215
• /
• 2014

Composites layer of Al-Cr-Ni-O system was prepared on a steel plate by hydro-thermal process at $700^{\circ}C$ for 12 hours, which phase identification and thermal conductivity were determined. The composites layer consisted of aluminum nitride, alumina, chromium carbide and aluminium, which density was $3.7kg/m^3$. The thermal conductivity of the coating layer determined by thermal data acquisition system was about 98.0 W/m/ which depended on the AlN content. Numerical modelling of the heat transfer behavior of the coating layer was well agreement with the empirical data.

• Nuclear Engineering and Technology
• /
• 제45권5호
• /
• pp.689-694
• /
• 2013

A duplex stainless steel sheet with 1 wt.% gadolinium was fabricated for a neutron absorbing material with high strength, excellent corrosion resistance, and low cost as well as high neutron absorption capability. The microstructure of the as-cast specimen has typical duplex phases including 31% ferrite and 69% austenite. Main alloy elements like chromium (Cr), nickel (Ni), and gadolinium (Gd) are relatively uniformly distributed in the matrix. Gadolinium rich precipitates were present in the grains and at the grain boundaries. The solution treatment at $1070^{\circ}$ for 50 minutes followed by the hot-rolling above $950^{\circ}$ after keeping the sheet at $1200^{\circ}$ for 1.5 hours are important points of the optimum condition to produce a 6 mm-thick plate without cracking.

• Corrosion Science and Technology
• /
• 제7권1호
• /
• pp.61-67
• /
• 2008

In this paper, electrochemical and microstructural characteristics of nickel-plated Alloy 600 were investigated in order to identify the performance of electroless Ni-plating on Alloy 600 in high-temperature aqueous condition with the comparison of electrolytic nickel-plating. For high temperature corrosion test of nickel-plated Alloy 600, specimens were exposed for 770 hours to typical PWR primary water condition. During the test, open circuit potentials (OCP's) of all specimens were measured using a reference electrode. Also, resistance to flow accelerated corrosion (FAC) test was examined in order to check the durability of plated layers in high-velocity flow environment at high temperature. After exposures to high flow rate aqueous condition, the integrity of surfaces was confirmed by using both scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). For the field application, a remote process for electroless nickel-plating was demonstrated using a plate specimen with narrow gap on a laboratory scale. Finally, a practical seal design was suggested for more convenient application.

• Journal of Welding and Joining
• /
• 제18권6호
• /
• pp.74-82
• /
• 2000

The fluxless wetting properties of UBM-coated Si-wafer to the binary lead-free solders(Sn-Ag, Sn-Sb, Sjn-In, Sn0Bi) were estimated by wetting balance method. With the new wettability indices from the wetting curves of one side coated specimen, the wetting property estimation of UBM-coated Si-wafer was possible. For UBM of Si-chip, Au/Cu/Cr UBm was better than au/Ni/TI in the point of wetting time/ At general reflow process temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) was better than that of low melting point one(Sn-Bi, Sn-In). The contact angle of the one side coated Si-plate to the solder could be calculated from the force balance equation by measuring the static state force and the tilt angle.

• 한국표면공학회지
• /
• 제36권2호
• /
• pp.184-193
• /
• 2003

Cyclic sweep voltametry was performed to investigate the electrochemical behavior of heavy metal ions and the organic additives in surface finishing process. And electrolysis using parallel plate electrode electrolyzer was carried out to simulate the treatment of real waste water. Results showed that more than 99 percent of Cu was recovered and selective recovery of Cu in mixed waste water was possible, but the possibility of economical recovery of Ni and Cr were very low due to the evolution of hydrogen gas. Electrochemical oxidation of cyanide and organic additives on anode showed very excellent removal rate. The complete removal of several hundred ppm of cynide was possible within several tens minutes and organics within 2 or 3 hours. Even in case of concentrate waste water, the complete removal of COD by using NaCl and air stirring seemed to be possible.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.17-20
• /
• 2006

A flat plate-column connection is susceptible to brittle punching shear failure, which may result in the necessity of shear reinforcement. In previous, experimental tests were performed to study the capacity of slab-column connections strengthened with various shear reinforcement, and the capacity of the specimens with lattice reinforcement are superior to the others. In present study, to study for effects of details of lattice reinforcement, experimental studies was performed. Main parameters are the amount of lattice shear reinforcement, arrangement of lattice and the effect of flexural re-bar. And capacity of the specimen with small amount of lattice reinforcement was higher than the capacity of other shear reinforcement.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.711-714
• /
• 2000

In this study, the physical properties of the acoustic element and case with metal-piezoelectric ceramics were analyzed. The dielectric and piezoelectric properties of 0.5 wt% MnO$_2$and NiO doped 0.1Pb(Mg$\_$1/3Nb$\_$2/3)O$_3$-0.45PbTiO$_3$-0.45PbZrO$_3$ceramics were investigated aiming at acoustic transducer applications. The vibration characteristics for the laminated circular plate was analyzed for the various thickness and diameter of the piezoceramic layer and metal layer. Also, the acoustic characteristics for the geometrical form of case have been investigated. The design and fabrication method worked in this paper can be utilized in development of actuator and acoustic device.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.413-416
• /
• 2000

In this study, the physical properties of the acoustic element and case with metal-piezoelectric ceramics were analyzed. The dielectric and piezoelectric properties of 0.5 wt% MnO$_2$ and NiO doped 0.1Pb(Mg$_{1}$3/Nb$_{2}$3/)O$_3$-0.45PbTiO$_3$-0.45PbZrO$_3$ceramics were investigated aiming at acoustic transducer applications. The vibration characteristics for the laminated circular plate was analyzed for the various thickness and diameter of the piezoceramic layer and metal layer. Also, the acoustic characteristics for the geometrical form of case have been investigated. The design and fabrication method worked in this paper can be utilized in development of actuator and acoustic device.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.423-427
• /
• 1999

Electroplating of 80%Ni permalloy thin plate for magnetic core materials. was studied The convected flow of electrolyte was used for stirring methode. The current density could be increased up to 250mA/$\textrm{cm}^2$ by flow cell. The composition of electroplated layer with vespect to current density and flow rate was investigated and experimental equation to predict the composition was made. How cell yielded more uniform thickness distribution than paddle cell did. The composition distribution was also studied. The thickness was the most important factor to the permeability. The permeability of 5$\mu\textrm{m}$plated permalloy was over 2000 at 1 MHz.

• 암석학회지
• /
• 제11권1호
• /
• pp.17-28
• /
• 2002

제주도 남동부 태흥리 용암류에 대한 암석학적, 지구화학적 특징에 대해 고찰하였다. 본 역의 용암류는 알칼리 현무암과 쏠리아이트 현무암으로 구분된다. 하층부에는 4매 이상의 쏠리아이트 현무암이 나타나고, 그 위를 2매의 알칼리 현무암이 덮고 있다. 쏠리아이트 현무암은 알칼리 현무암에 비해, 동일한 MgO 조성에서 $K_2O$, $P_2O_{5}$, Ba과 Ta은 낮은 값을 가지고, $SiO_2$와 CaO는 높은 값을 가진다. 미량원소의 조성 특징을 원시맨틀 값으로 규정화한 거미 성분도에서 모든 현무암질 마그마의 Ba과 Rb은 원시맨틀에 비하여 부화되어 있고, Ni 과 Cr은 결핍되어 있다. 희토류 원소를 콘드라이트 값으로 표준화했을 때 LREE가 HREE에 비해 더 부화된 패턴을 가진다. 변화 패턴은 나란한 변화를 보이며, 알칼리 현무암이 쏠리아이트 현무암보다 더 부화된 경향을 보인다. 조구적 위치 판별도에서 본 역의 용암류는 지판 내부 현무암 영역에 도시된다. 쏠리아이트 현무암의 Zr/Nb, Y/Nb, $Al_2O_3$/$P_2O_{5}$ 비는 알칼리 현무암에 비해 크며, K/Ba비는 알칼리 현무암과 쏠리아이트 현무암간에 거의 차이가 없이 일정한 값을 나타낸다. 본 연구지역의 화산암류에 대한 일련의 지화학적 특징은 알칼리 현무암과 쏠리아이트 현무암의 모마그마가 동질의 맨틀 근원암으로부터 부분용융 정도의 차이에 의해 생성되었음을 지시하며, 쏠리아이트 현무암이 알칼리 현무암보다 더 큰 정도의 부분용융으로 형성되었음을 의미한다.