• 한국수소및신에너지학회논문집
• /
• 제20권2호
• /
• pp.161-167
• /
• 2009

The regulation of the $CO_2$ emit from vehicles have become much more stringent in recent years. This stringent regulation is more request vehicle manufacturers to develop the alternative fuel vehicles for reducing exhaust emissions. LPG fuel is more clean energy compares with gasoline and diesel fuel. Especially, $CO_2$ emission of LPG Vehicle is less than gasoline vehicle and almost equal to diesel vehicle. For this reason, recently korean government is extending LPG fuel for hybrid car and light duty vehicle. In domestic, Propane is mixing $15{\sim}30%$ to butane for improvement of cold start at winter season. Therefore, In this paper was investigated that the characteristics of emissions according to propane mixing rate with 0, 10, 20, 30% were compared and analyzed by the vehicle test using LPG vehicle according to the FTP75 mode. It was also investigated the characteristics of nano-particle emit with propane mixing rate.

• 한국수소및신에너지학회논문집
• /
• 제29권5호
• /
• pp.458-465
• /
• 2018

This study reports the fabrication of anion exchange membranes (AEMs) containing two kinds of functional groups: i) trimethylphosphite (TMP) and ii) trimethylamine (TMA). We carried out the synthesis of polymers to enhance thermal stability and ion conductivity. The alternative polymer was prepared using 2,2-bis(4-hydroxy-3-methylphenyl)propane and decafluorobiphenyl. The membrane was fabricated by solution casting method. The thermal stability of membranes was examined by TGA. The physiochemical properties of membranes were also investigated in terms of water uptake, swelling ratio, ion exchange capacity, and ion conductivity. The hydroxide ion conductivity of the membranes reached about 20.2 mS/cm for quaternary ammonium poly(arylene ether) (QA-PAE) containing TMA moiety and 5.1 mS/cm for quaternary phosphonium PAE (QP-PAE) containing TMP moiety at $90^{\circ}C$.

• 한국수소및신에너지학회논문집
• /
• 제27권4호
• /
• pp.357-364
• /
• 2016

Recently, the world faces the environmental problem such as air pollution due to harmful gas discharged from car and abnormal climate due to the green-house gases increased by the discharge of $CO_2$. Compressed Natural Gas (CNG), one of alternative for this problem, is less harmful, compared to the existing fossil fuel, as gaseous fuel, and less carbon in fuel ingredients and carbon dioxide generation rate relatively favorable more than the existing fuel. However, CNG fuel has the weakness of slow flame propagation speed and difficult fast burn. On the other hand, hydrogen does not include carbon in fuel ingredients, and does not discharge harmful gas such as CO and HC. Moreover, it has strength of quick burning velocity and ignition is possible with small ignition energy source and it's has wide Lean Flammability Limit. If using this hydrogen with CNG fuel, the characteristics of output and discharge gas is improved by the mixer's burning velocity improved, and, at the same time, is possible to have stable lean combustion with the reduction of $CO_2$ expected. Therefore, this research tries to identify the characteristics of engine and emission gas when mixing CNG fuel and hydrogen in each portion and burning them in spark igniting engine, and grasp the combustion stability and emission gas characteristics according and use it as the basic data of hydrogen-CNG premixed engine.

• Korean Chemical Engineering Research
• /
• 제54권4호
• /
• pp.519-526
• /
• 2016

Biomass derived jet fuel is proven as a potential alternative for the currently used fossil oriented energy. The efficient production of jet fuel precursor with special molecular structure is prerequisite in producing biomass derived jet fuel. We synthesized a new jet fuel precursor containing branched $C_{15}$ framework by aldol condensation of furfural (FA) and ethyl levulinate (EL), where the latter of two could be easily produced from lignocellulose by acid catalyzed processes. The highest yield of 56% for target jet fuel precursor could be obtained at the optimal reaction condition (molar ratio of FA/EL of 2, 323 K, 50 min) by using KOH as catalyst. The chemical structure of $C_{15}$ precursor was specified as (3E, 5E)-6-(furan-2-yl)-3-(furan-2-ylmethylene)-4-oxohex-5-enoic acid ($F_2E$). For stabilization, this yellowish solid precursor was hydrogenated at low temperature to obtain C=C bonds saturated product, and the chemical structure was proposed as 4-oxo-6-(tetrahydrofuran-2-yl)-3-(tetrahydrofuran-2-yl)-methyl hexanoic acid ($H-F_2E$). The successful synthesis of the new jet fuel precursors showed the significance that branched jet fuel could be potentially produced from biomass derived FA and EL via fewer steps.

• 한국수소및신에너지학회논문집
• /
• 제27권5호
• /
• pp.604-611
• /
• 2016

This paper describes the characteristics of n-Butane fuel for the homogeneous charge compression ignition (HCCI) engine for a new concept. HCCI engines are being considered as a future alternative for diesel and gasoline engines. From the experimental observations, the effect of n-Butane fuel in HCCI engine on CO, HC and NOx are analysed. The objective of this paper is to clear the effects of equivalence ratio and inlet temperature with n-Butane on the HCCI. For this purpose, a 4-cylinder, compression ignition engine was converted into a HCCI engine This work has been run with n-butane fuel at a constant speed.

• 한국수소및신에너지학회논문집
• /
• 제23권3호
• /
• pp.227-235
• /
• 2012

Finding an alternative fuel and reducing environmental pollution are the main goals for future internal combustion engines. The purpose of this study is to obtain low-emission and high-efficiency by hydrogen enriched LPG fuel in constant volume chamber. An experimental study was carried out to obtain fundamental data for the combustion and emission characteristics of pre-mixed hydrogen and LPG in a constant volume chamber (CVC) with various fractions of hydrogen-LPG blends. To maintain equal heating value of fuel blend, the amount of LPG was decreased as hydrogen was gradually added. Exhaust emissions were measured using a HORIBA exhaust gas analyzer for various fractions of hydrogen-LPG blends. The results showed that the rapid combustion duration was shortened, and the rate of heat release elevated as the hydrogen fraction in the fuel blend was increased. Moreover, the maximum rate of pressure rise also increased. These phenomena were attributed to the burning velocity which increased exponentially with the increased hydrogen fraction in the $H_2$-LPG fuel blend. Exhaust HC and $CO_2$ concentrations decreased, while NOX emission increased with an increase in the hydrogen fraction in the fuel blend. Our results could facilitate the application of hydrogen and LPG as a fuel in the current fossil hydrocarbon-based economy and the strict emission regulations in internal combustion engines.

• 신재생에너지
• /
• 제4권2호
• /
• pp.81-86
• /
• 2008

Rotary kiln in cement work has been evaluated for a wide variety of organic wastes such as wood, used tyres, plastic wastes and automobile shredder residue (ASR). However the presence of chlorine hampers the use of ASR as fuel in rotary kiln. Therefore, the behavior characteristics of chlorine components in rotary kiln should be considered to develop an effective method for ASR treatment to recovery energy resources. The aim of this paper is to present the chlorine control system applied to a cement manufacturing process for ASR use as an alternative fuel. In this work, the simulation of bypass unit and cyclones for chlorine control in rotary kiln has been studied and compared with the operation results of field test.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1998년도 춘계학술발표회논문집(2)
• /
• pp.1026-1031
• /
• 1998

A licensing approach for new fuel design is propose. It includes the possible licensing options to be taken according to the level of significance of design changes. This approach can be applied on legal grounds of the AEA, Article 44.3 and Article 21, but implies that the related ERAEAs should be revised or other alternative regulatory guidelines should be prepared. However, it is not intended to invoke additional requirements but rather to streamline and formulate the current practice by using one of supplementary provisions of the AEA, Article 104.2 which is recently enacted for approval of the technical report on a special topic.

• 한국수소및신에너지학회논문집
• /
• 제14권4호
• /
• pp.291-297
• /
• 2003

As an alternative bipolar plate material for polymer electrolyte membrane fuel cell (PEMFC), TiN-coated 316 stainless was evaluated in terms of electrical contact resistance and water contact angle. Performance and lifetime of the TiN-coated 316 bipolar plates were measured in comparison with those of graphite and bare 316 bipolar plates. At a cell voltage of 0.6 V, current density of the single cells using graphite, AISI 316, and TiN/316 bipolar plates was 996, 796, and $896mA/cm^2$, respectively. By coating 316 stainless steel with TiN layer, performance degradation rate determined to be the voltage degradation rate at a cell voltage of 0.6 V was reduced from 2.3 to 0.43 mV/h.

• 한국수소및신에너지학회논문집
• /
• 제27권4호
• /
• pp.386-403
• /
• 2016

Biofuels produced from biomass can be substituted for petroleum fuels due to GHG reduction, sustainability and environmental friendly. The process technologies that convert biomass into biofuels are varied and depend on the feedstocks. Microalgae are considered to be one of the most promising alternative source to the conventional feedstocks for biofuel. Microalgae can be converted to biodiesel, bioethanol, biogas and biojet fuel via thermolchemical and biochemical production technologies. This reviews discusses recent advance in understanding the effects of the characteristics of various processes on the production of biofuels using microalgae. The performances of microalgae based biofuel are compared.