• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.53-61
• /
• 2004

In this paper, we proposed a new architecture of MAC(Multiplier-Accumulator) to operate high-speed multiplication-accumulation. We used the MBA(Modified radix-4 Booth Algorithm) which is based on the 1's complement number system, and CSA(Carry Save Adder) for addition of the partial products. During the addition of the partial product, the signed numbers with the 1's complement type after Booth encoding are converted in the 2's complement signed number in the CSA tree. Since 2-bit CLA(Carry Look-ahead Adder) was used in adding the lower bits of the partial product, the input bit width of the final adder and whole delay of the critical path were reduced. The proposed MAC was applied into the DWT(Discrete Wavelet Transform) filtering operation for JPEG2000, and it showed the possibility for the practical application. Finally we identified the improved performance according to the comparison with the previous architecture in the aspect of hardware resource and delay.

• Journal of Bio-Environment Control
• /
• v.23 no.4
• /
• pp.391-400
• /
• 2014

The number of large scale greenhouses has recently been increasing to cope with mass consumption of agricultural product. Korean government announced a new development plan for constructing greenhouse complex in reclaimed lands for the purpose of improvement in exports and activation of domestic market of agricultural product. Wind environment in the reclaimed land is totally different from that of inland area, and it can give a strong influence on ventilation performance of naturally ventilated greenhouse facilities. In this study, internal airflow analysis of naturally ventilated greenhouse built on a reclaimed land was conducted using wind tunnel and PIV for validation research. Later, the PIV measured results will be used to improve the accuracy of 3 dimensional CFD simulation in the future. Wind profile at a reclaimed land was produced using ESDU program and it was applied to the wind tunnel. The calculated error was only 5% and 0.96 of correlation coefficient, implying that the computed profiles were designed properly. From the measured results, when external wind speed changed from $1m{\cdot}s^{-1}$ to $1.5m{\cdot}s^{-1}$, air velocities inside the greenhouse which PIV measured were also increased proportionately in case of both side vent open and side-roof vent open. Considering reduced ratio of air velocity inside the greenhouse, it was measured a minimum of 40% in case of side vent and 30% in case of side-roof vent compared with external wind speed from each vent type. From the quantitative and qualitative PIV analysis, the PIV measured results indicated that there were well ventilated and stagnant areas in the greenhouse according to external wind condition as well as ventilation design.

• Journal of Convergence for Information Technology
• /
• v.7 no.3
• /
• pp.111-116
• /
• 2017

This study offers the possibility as a new product of souvenirs from cultural tourist sites with virtual reality contents, instead of a simple exhibit. Users can watch augmented reality contents on souvenirs, and use the virtual experience service of cultural tourist sites with VR viewer. It has 4K-class high-quality $360^{\circ}$ image capture to increase the immersion of users in virtual space, implement virtual reality space and intuitive UI interaction with users using IMU (Inertial Measurement Unit). It is also possible to apply various add-on functions, including 3D contents, through technical development to increase its marketability, and apply in other industries. In addition, the prototype of the souvenir and VR viewer will be made by using a 3D printer and such in order to apply the contents which will be introduced in this study. Various product expansions can be considered through consultation with the relevant companies for the use of ready-made products.

• Economic and Environmental Geology
• /
• v.46 no.6
• /
• pp.593-602
• /
• 2013

Biodiesel is an important new alternative transportation fuel and it can be produced by chemically reacting a fat or oil with an alcohol, in the presence of a catalyst. The product of the reaction is a mixture of methyl esters, which are known as biodiesel, and glycerol, which is a high value co-product. The process is known as transesterification. Biodiesel can be used neat and when used as a pure fuel it is known as BD100. However, it is often blended with petroleum-based diesel fuel and when this is done the blend is designated BD5 or BD20(BD20 is a blend of 20% biodiesel and 80% petroleum diesel fuel). Adherence to a quality standard is essential for proper performance of the fuel in the engine and will be necessary for widespread use of biodiesel. In this study, we analyzed 4,144 papers of biodiesel by category, country, institution, keyword etc. from 2001 to 2013 years.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.1
• /
• pp.98-115
• /
• 2012

New trend called ubiquitous leads the recent business by standardization and integration. It should be the main issue how to guarantee the integration and accountability on each business, especially in mission critical system which is mainly supported by M2M (Machine to Machine) control mechanism. This study is from the analysis of digital forensics case study that is from the M2M Sensing Control Mechanism problem of the "Imjin River" case in 2009, where a group of family is swept away to death by water due to M2M control error. The ubiquitous surroundings bring the changes in the field of criminal investigation to real time controls such as M2M systems. The needs of digital forensics on M2M control are increasing on every crime scene but we suffer from the lack of control metrics to get this done efficiently. The court asks for more accurately analyzed results accounting high quality product development design. Investigators in the crime scene need real-time analysis against the crime caused by poor quality of mission critical systems. It seems to be every need of Real-Time-Enterprise, so called ubiquitous society on the case. We try to find the efficiency and productivity in discovering non-functional design defects in M2M convergence products focusing on three metrics in study model with quick implementation. Digital forensics system in present status depends on know-how of each investigator and is hard to expect professional analysis on every field. This study set up a hypothesis "Co-working of professional investigators on each field will qualify Performance and Integrity" especially in mission critical system such as M2M and suggests "Online co-work analysis model" to efficiently detect and prevent mission critical errors in advance. At the conclusion, this study proved the statistical research that was surveyed by digital forensics specialists around M2M crime scene cases with quick implementation of dash board.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.16 no.6
• /
• pp.267-276
• /
• 2021

The automotive industry and academic research have been continuously conducting research on standardization such as AUTOSAR (AUTomotive Open System ARchitecture) and ISO26262 to solve problems such as safety and efficiency caused by the complexity of electric/electronic architecture of automotive. AUTOSAR is an automotive standard software platform that has a layered structure independent of MCU (Micro Controller Unit) hardware, and improves product reliability through software modularity and reusability. And, ISO26262, an international standard for automotive functional safety and suggests a method to minimize errors in automotive ECU (Electronic Control Unit)s by defining the development process and results for the entire life cycle of automotive electrical/electronic systems. These design methods are variously applied in representative automotive safety-critical systems. However, since the functional and safety requirements are different according to the characteristics of the safety-critical system, it is essential to research the AUTOSAR functional safety design method specialized for each application domain. In this paper, a software functional safety mechanism design method using AUTOSAR is proposed, and a new failure management framework is proposed to ensure the high reliability of the product. The AUTOSAR functional safety mechanism consists of memory partitioning protection, timing monitoring protection, and end-to-end protection. The fault management framework is composed of several safety SWCs to maintain the minimum function and performance even if a fault occurs during the operation of a safety-critical system. Finally, the proposed method is applied to the Shift-by-Wire system design to prove the validity of the proposed method.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.21 no.3
• /
• pp.67-80
• /
• 2019

The purpose of this study was to clarify store attributes for nail stores (focusing on independent stores) by qualitative research. Even though the nail market is showing a steady increase in terms of sales amounts, and the number of stores, related studies were very rare. Meanwhile, as long as the nail market is growing, many stores are suffering from bad business performance because of new nail stores are relatively easier to open than beauty or hair stores, but the nail stores don't have a discriminated marketing strategy. As nail the market is rapidly increasing, finding factors that led to success for nail stores is very meaningful, both for academics and business. The reason that qualitative research should be done before the quantitative research is due to scant theoretical background concerning this matter. For this qualitative research, 8 experts who are operating nail stores as an owner or a manager or a professor at a university who had over 5 years of related working experience were included. The attributes for nail stores were derived using one-to-one in-depth interviews conducted from March 3 to May 31, 2019. As a result of the qualitative studon the attributes for nail stores, it turned out that there were 5 factors-physical environment, product, speed, profitability, and reliability. Physical environment, product, and profitability were mentioned in most related surveys, but some details showed that and speed and reliability have been newly highlighted. Many unknown issues that were not easy to acquire from common academic research are included. After this study, I hope that many marketers may get basic conditions to apply to real businesses and that they can use it as effective data for the following quantitative research.

• Ecology and Resilient Infrastructure
• /
• v.7 no.4
• /
• pp.248-255
• /
• 2020

In this study, we analyze the current state of domestic food waste (FW) recycling and propose a management plan for greenhouse gas (GHG) emissions. First, the composting potential of the GW demonstrates considerable promise. In particular, the GW (phytoplankton, periphyton, macrophyte, etc.) as a third-generation biomass shows strong performance as a functional additive that mitigates the disadvantages associated with composting FW and improves the quality of the final composted product. Alternatively, the final product (e.g., soil ameliorant) can be used to produce bio-filters that are effective pollutant buffers, with high applicability for green infrastructure. The proposed ecological approaches create new opportunities for FW as a resource for the reduction of GHG emissions, and are expected to contribute to the establishment of effective net-zero carbon systems in the future.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.1
• /
• pp.173-180
• /
• 2022

Approximate Computing is a promising method for designing hardware-efficient computing systems. Approximate multiplication is one of key operations used in approximate computing methods for high performance and low power computing. An approximate 4-2 compressor can implement hardware-efficient circuits for approximate multiplication. In this paper, we propose an approximate multiplier with low area and low power characteristics. The proposed approximate multiplier architecture is segmented into three portions; an exact region, an approximate region, and a constant correction region. Partial product reduction in the approximation region are simplified using a new 4:2 approximate compressor, and the error due to approximation is compensated using a simple error correction scheme. Constant correction region uses a constant calculated with probabilistic analysis for reducing error. Experimental results of 8×8 multiplier show that the proposed design requires less area, and consumes less power than conventional 4-2 compressor-based approximate multiplier.

• Journal of Intelligence and Information Systems
• /
• v.28 no.2
• /
• pp.1-18
• /
• 2022

As digital technology converges into the e-commerce market across industries, online transactions have activated, and the use of online has increased. With the recent spread of infectious diseases such as COVID-19, this market flow is accelerating, and various product information can be provided to customers online. Providing a variety of information provides customers with various opportunities but causes difficulties in decision-making. The recommendation system can help customers to make a decision more effectively. However, the previous research on recommendation systems is limited to only quantitative data and does not reflect detailed factors of products and customers. In this study, we propose an intelligent recommendation system that quantifies the attributes of products and customers by applying text mining techniques to qualitative data based on online reviews and integrates the existing objective indicators of total star rating, sentiment, and emotion. The proposed integrated recommendation model showed superior performance to the overall rating-oriented recommendation model. It expects the new business value to be created through the recommendation result reflecting detailed factors of products and customers.