• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.1
• /
• pp.115-124
• /
• 1989

Near-threshold fatigue crack-growth behavior at room temperature for a duplex stainless steel weldments was investigated to evaluate the effect of load ratio, microstructural change, and residual stresses. Near-threshold fatigue crack propagation behavior is found to show a marked sensitivity to .alpha./.gamma. phase ratio, and little residual stress effects. Threshold values in the heat affected zones are higher than those of base metals and threshold values for crack growth decrease with increasing the load ratio in the base metals and weldments. The fractrographic features in base metals, weldments and heat affectred zones were discussed in terms mechanism of crack growth.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.3
• /
• pp.39-47
• /
• 1997

Recently developed TMCP steels, which were manufactured by controlled rolling followed by accelerated cooling process, were examined to study their characteristics and weldability. Accelerated cooling type TMCP steel's hardness test result exhibited high value on weld zone. On the contrary, base metal and HAZ exhibited comparatively the similar value. On this experiment result Softening of HAZ is not occurred. in the-heat affected zone, grain size repression be caused by chemical composition properties which a small quantity Al-Ti-B-N. Changing stress ratio near-threshold fatigue crack propagation experiments were carried out. According to this result, crack propagation velocity of the HAZ exhibited slower than the base metal and near-threshold value had increased at the HAZ. Finally accelerated cooling type TMCP steels were exhibited excellent mechanical properties in both strength and toughness.

• Journal of the Korean Society of Safety
• /
• v.15 no.3
• /
• pp.1-6
• /
• 2000

In fatigue crack growth test, it is important not only to analyze characteristics of fatigue crack growth but also to determine the threshold stress intensity factor, ${\Delta}K_{th}$. which is the threshold value of fatigue crack growth. Linear regression analysis using fatigue test data near the threshold is suggested to determine the ${\Delta}K_{th}$ in the standard test method but the ${\Delta}K_{th}$ can be affected by a fitting method. And there are some limitations on the linear regression analysis in the case of small number of test data near the threshold. The objective of this study is to investigate differences of the ${\Delta}K_{th}$ due to regression analysis method and to evaluate the relative error range of the ${\Delta}K_{th}$ in same fatigue crack growth test data.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.678-684
• /
• 2015

Near-threshold computing (NTC) is now regarded as a promising candidate for innovative power reduction, which cannot be achieved with conventional super-threshold computing (STC). However, performance degradation and vulnerability to process variation in the NTC regime are the primary concerns. In this paper, we propose a voltage- and frequency-tuning methodology for mitigating the process-variation-induced problems in NTC-based manycore architectures. To implement the proposed methodology, we build up multiple-voltage multiple-frequency (MVMF) islands and apply a voltage-frequency tuning algorithm based on the critical-path monitoring technique to reduce the effects of process variation and maximize energy efficiency in the post-silicon stage. Experimental results show that the proposed methodology reduces overall power consumption by 8.2-20.0%, compared to existing methods in variation-sensitive NTC environments.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.2
• /
• pp.159-164
• /
• 2016

A wireless communication system is required to be implemented with the low power circuits because it uses a battery having a limited energy. Therefore, the current mode circuit has been studied because it consumes constant power regardless of the frequency change. However, the clock-feedthrough problem is happened by leak of stored energy in memory operation. In this paper, we suggest the current memory circuit to minimize the clock-feedthrough problem and introduce a technique for ultra low power operation by inducing dynamic voltage scaling. The current memory circuit was designed with BSIM3 model of $0.35{\mu}m$ process and was operated in the near-threshold region. From the simulation result, the clock-feedthrough could be minimized when designing the memory MOS Width of $2{\mu}m$, the switch MOS Width of $0.3{\mu}m$ and dummy MOS Width of $13{\mu}m$ in 1MHz switching operation. The power consumption was calculated with $3.7{\mu}W$ at the supply voltage of 1.2 V, near-threshold voltage.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.157-160
• /
• 2002

The dosage of intra-operative BNCT using near-threshold $^{7}$ Li(p,n)$^{7}$ Be direct neutrons was evaluated with the calculation method validated with the phantom experiment. The production of both neutrons by near-threshold $^{7}$ Li(p,n)$^{7}$ Be and gamma rays by $^{7}$ Li(p,p'gamma)$^{7}$ Li in a Li target was calculated using Lee's method and their transport in the phantom was calculated with MCNP-4B. As a result, the region satisfying the requirements of the protocol in intra-operative BNCT for brain tumors in Japan was acknowledged to be comparable to present BNCT, for the proton energy of 1.900 MeV for example. A boron-dose enhancer (BDE) introduced in this study to increase $^{10}$ (n,$\alpha$)$^{7}$ Li dose in a living body was effective. The void used to increase doses in deep regions was also valid with the BDE. It was found that intra-operative BNCT using near-threshold $^{7}$ Li(p,n)$^{7}$ Be direct neutrons is feasible.

• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.2
• /
• pp.37-44
• /
• 1990

The effect of the microstructural change on the near threshold fatigue crack growth rate in SM40C steel has been studied using the ${\Delta}K$ decreasing method. Below the total strain amplitude of 0.56%, cyclic softening occured, whereas above this value cyclic hardening occurred in the pearlitic lamellar structure. However, in the spherodized structure the cyclic hardening solely occurred. The crack growth rate in the near-threshold region was decreased with increasing prior austenite grain size and this was due to surface roughness. The crack growth rate of the spherodized structure was lower than that of the pearlite lamellar structure and the ${\Delta}K_{th}$ of the former was higher than that of the latter. It was understood that the crack propagates preferentially through the ferrite phase. The intergranular facets in the near-threshold region appeared in the spherodized structure.

• Journal of Korean Physical Therapy Science
• /
• v.2 no.4
• /
• pp.771-778
• /
• 1995

The purpose of this study was to determine the effects of linear polarized near-infrared ray radiation on experimental pain threshold in healthy adult subjects. Thirty healthy adult subjects were divided into 5 groups: 1) group 1, super lizer radiation at 0 % ; 2) group 2, super lizer radiation at 10 % ; 3) group 3, super lizer radiation at 20 % ; 4) group 4, super lizer radiation at 40 % ; 5) group 5, super lizer radiation at 80 %. The polarized near-infrared ray radiation was applied on LI 4 point of subject's right hand at a fixed time for 30 second. Experimental pain threshold were measured with electrical current on the right hand at 5 intervals for each radiation: 1) pretreat; 2) posttreat ; 3) posttreat of 1/2 hr ; 4) posttreat of 1 hr ; and 5) posttreat of 2 hrs. Data were analyzed using analyses of variance with repeated measures for pain threshold. No significant interaction between power output and time for pain threshold was found. Significant effects of power output and time for experimental pain threshold were found. Significant increase was noted in experimental pain threshold in group 4 and group 5 at posttreat, posttreat of 1/2, 1 hr and 2 hrs as a result of the applications of the polarized near-infrared ray radiation. This study indicate that polarized near-infrared ray radiation with above 40 % of power output increases pain threshold, thus possibly increasing options in choosing radiation output for treating pateint with pain. Further study is needed to compare the effects of these radiation in patients with clinical pain.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.4
• /
• pp.266-277
• /
• 1997

Near-threshold fatigue crack growth characteristics was investigated on the Ni-Cr-Mo-V low alloy steel, which has the different microstructure obtained by tempering at various temperature. The specimens were austenized at $950^{\circ}C$ and then followed by tempering at $200^{\circ}C$, $530^{\circ}C$ and $600^{\circ}C$. Strain rate was obtained from strain gauge attached on the crack tip and crack opening point was observed through load-strain curve. Threshold stress intensity range(${\Delta}K_{th}$) was increased with increasing tempering tempuerature, but the effective threshold stress intensity rage (${\Delta}K_{eff,\;th}$) was not affected with the increasing temperature. Grain size increased with increasing tempering temperature.

• Journal of the Optical Society of Korea
• /
• v.20 no.3
• /
• pp.407-412
• /
• 2016

We analyzed through numerical simulations the properties of a square beam homogenizer near the target for laser shock peening. The efficiency was calculated near the target by considering the plasma threshold of the metals. We defined the depth of focus of the square beam homogenizer with a given efficiency near the target. Then, we found the relationship between the depth of focus for the laser shock peening and four main parameters of the square beam homogenizer: the plasma threshold of the metal, the number of lenslets in the array-lens, the focal length of the condenser lens and the input beam size.