• E2M - 전기 전자와 첨단 소재
• /
• 제10권7호
• /
• pp.645-650
• /
• 1997

We manufactured CoNbZr/Cu/CoNbZr multi-layer films by rf magnetron sputtering methods and formed the patterns on the deposited multi-layer films. In this study, we fabricated a new etchant for forming the patterns by the wet etching with etchant and we searched for the best etching conditions and the etchant composition. Cu was etched selectively independent on the concentration of iron chloride solution, but amorphous CoNbZr thin film did not. The etchant was achieved by iron chloride solution(17.5 mol%) mixed with HF (20 mol%) during 150 sec, which etched CoNbZr/Cu/CoNbZr multi-layer films at the same time. Also, the etchant etched CoNbZr/Cu/CoNbZr multi-layer films by the three-step. It was shown that the cross-section had the isotropic structure and excellent etching characteristics with the above etchant.

• 한국분말재료학회지
• /
• 제28권4호
• /
• pp.317-324
• /
• 2021

High-strength low-alloy (HSLA) steels show excellent toughness when trace amounts of transition elements are added. In steels, prior austenite grain size (PAGS), which is often determined by the number of added elements, is a critical factor in determining the mechanical properties of the material. In this study, we used two etching methods to measure and compare the PAGS of specimens with bainitic HSLA steels having different Nb contents These two methods were nital etching and picric acid etching. Both methods confirmed that the sample with high Nb content exhibited smaller PAGS than its low Nb counterpart because of Nb's ability to hinder austenite recrystallization at high temperatures. Although both etching approaches are beneficial to PAGS estimation, the picric acid etching method has the advantage of enabling observation of the interface containing Nb precipitate. By contrast, the nital etching method has the advantage of a very short etching time (5 s) in determining the PAGS, with the picric acid etching method being considerably longer (5 h).

• 한국전기전자재료학회논문지
• /
• 제16권8호
• /
• pp.731-735
• /
• 2003

Ti-indiffused LiNbO$_3$waveguide have been used to various high speed optical device based on electro-optic effect such as modulators, switches, and sensor, etc. In order to high speed modulation of optical modulator have, one of the further devices, needed to increasing of electrode surrounding air by LiNbO$_3$dry etching because of impedance matching for optical and RF phase velocity between waveguide and electrode. We studied property of LiNbO$_3$dry etching after waveguide patterning lot optical modulation by using neutral loop discharge (NLD) plasma.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2009년도 동계학술발표회 논문집
• /
• pp.133-134
• /
• 2009

Cold temperature development (CTD) of electron beam (EB) patterned resists and subsequent dry etching were investigated for fabrication of nano-patterned Niobium (Nb). Bulky Nb fims on GaAs substrates were deposited with EB evaporation. Line patterns on Nb cathode were fabricated by EB patterning and reactive ion etching (RIE). Size deviations of nano-sized line patterns from CAD designed patterns are dependent on the EB total exposure, but it can be improved by CTD of EB-exposed resist. Line patterns of 10 to 300 nm widths of EB-exposed resist patterns were drawn under various exposure conditions of $0.2{\mu}s$/dot (total 240,000 dot) with a constant current (50 pA). Compared with room temperature development (RTD), the CTD improves pattern resolution due to the suppression of backscattering effect. RIE with $CF_4$ was performed for formation of several nano-sized line patterns on Nb. Each EB-resist patterned samples with RTDs and CTDs were etched with two different $CF_4$ gas pressures of 5 Pa. Nb etching rate increases while GaAs (or ZEP) etching rate decreases as the chamber pressure increases. This different dependent of the etching rate on the $CF_4$ pressure between Nb and GaAs (or ZEP) has a significant meaning because selective etching of nano-sized Nb line patterns is possible without etching of the underlying active layer.

• 한국세라믹학회지
• /
• 제40권9호
• /
• pp.886-890
• /
• 2003

단결정 LiNbO$_3$를 helicon wave plasma 방법으로 식각시 bias power와 CF$_4$, HBr, SR$_{6}$가 혼합된 gas 유량에 따른 식각 속도와 rms roughness 값의 특성을 관찰하였다. 식각된 깊이는 surface profiler로 관찰하였으며 rms roughness 값은 Atomic Force Microscopy (AFM)으로 측정하였다. Bias power 증가함에 따라 500W에서 가장 높은 식각 속도와 가장 평탄한 표면형상을 얻을 수 있었으며, CF$_4$, HBr, SF$_{6}$ gas 유량을 각각 10～30 sccm으로 증가시킴에 따라 식각 속도는 CF$_4$, HBr, SF$_{6}$ gas 유량이 10 sccm, 30 sccm, 10 sccm에서 가장 높게 나타났으며, rms roughness 값은 CF$_4$, HBr, SF$_{6}$ gas 유량이 30 sccm, 10 sccm, 30 sccm에서 가장 낮은 표면 조도를 나타내었다.

• 공업화학
• /
• 제17권3호
• /
• pp.327-330
• /
• 2006

Si nanodot 배열을 형성하기 위하여 $NbO_{x}$ nanopillar를 건식식각 공정의 식각마스크로써 이용하기 위한 가능성이 조사되었다. $NbO_{x}$ nanopillar는 Al과 Nb의 양극산화 공정을 이용하여 준비되었다. $NbO_{x}$ nanopillar의 식각속도와 식각프로파일은 고밀도 플라즈마를 이용한 반응성 이온 식각법에 의해서 식각가스의 농도와 coil rf power, 그리고 dc bias voltage를 각각 변화시키면서 조사 되었다. $Cl_{2}$ 가스의 농도가 증가할수록 $NbO_{x}$ nanopillar의 식각속도는 감소하였고 coil rf power와 dc bias voltage의 증가는 식각속도의 상승을 초래했다. 선택된 식각조건에서 식각시간을 변화하여 $NbO_{x}$ nanopillar의 식각특성 및 식각메커니즘이 조사되었다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.783-786
• /
• 2003

A simple fabrication method of self-aligned ridge waveguides with dielectric side buffers is demonstrated on +Z- cut LiNbO$_3$. The ridge waveguide is fabricated by a combination of the annealed proton exchange process and the proton-exchanged wet etching technique. The self-aligned process is achieved by wet etching of aluminum.

• Journal of Magnetics
• /
• 제14권2호
• /
• pp.71-74
• /
• 2009

The magnetic and structural properties of FINEMET (the Hitachi product name of the Fe-Si-B-Nb-Cu alloy) nanopowder with a composition of $Fe_{73.5}Si_{13.5}B_9Nb_3Cu_1$ atomic percent were investigated after annealing, chemical etching, and mechanical milling. The primary and secondary crystallization temperatures were 523 and $550^{\circ}C$, respectively. The grain size of the particles was adjusted by annealing time. Optimally annealed particles exhibited a homogenous microstructure composed of nanometer-sized crystalline grains. The grain boundary of the annealed particles was etched preferentially by chemical etching. Chemically etched particles were broken at the grain boundary by high-energy ball milling. As a result, a nanometer-sized FINEMET powder with a uniform size of crystalline grains was fabricated.

• 공업화학
• /
• 제25권1호
• /
• pp.53-57
• /
• 2014

본 연구에서는 micro-contact printing을 통하여 니오븀 호일 표면 위에 균일한 에칭 pits를 형성하였다. 균일한 보호층을 형성하고자 전해연마의 효과를 확인하였으며, 기존의 $O_2$ 플라즈마 공정 없이 손쉽게 균일한 에칭 pits를 형성시킬 수 있는 조건을 확인하였다. 메탄올 혼합 전해질을 사용하여 10 min 동안 에칭을 진행한 결과 니오븀 호일 표면 위에 지름과 간격이 각각 $10{\mu}m$와 $5{\mu}m$로 잘 정렬된 에칭 pits를 관찰하였다.

• 한국세라믹학회지
• /
• 제42권4호
• /
• pp.232-236
• /
• 2005

$LiNbO_{3}$ optical waveguide 구조를 neutral loop discharge plasma 방법으로 식각시 As과 $C\_{3}F_{8}$가 혼합된 가스 유량에 따른 식각속도와 표면조도 값의 특성을 관찰하였다. 식각 후 식각속도와 식각단면은 scanning electron microscopy로 비교 분석하였으며, 표면조도는 atomic force microscopy로 측정하였다. Ar과 $C_{3}F_{8}$가 혼합된 가스 유량비를 각각 0.1-0.5로 증가시킴에 따라 식각속도와 표면조도는 0.2에서 가장 높게 나타났으며, bias power를 증가함에 따라 300W에서 가장 우수한 식각속도와 가장 평탄한 표면 형상을 얻을 수 있었다.