• 열처리공학회지
• /
• 제19권3호
• /
• pp.176-185
• /
• 2006

• Advances in nano research
• /
• 제10권5호
• /
• pp.493-507
• /
• 2021

This article focused on studying the buckling behavior of two-dimensional functionally graded (2D-FG) nanosize tubes, including porosity based on first shear deformation and higher-order theory of tube. The nano-scale tube is simulated based on the nonlocal gradient strain theory, and the general equations and boundary conditions are derived using Hamilton's principle for the Zhang-Fu's tube model (as higher-order theory) and Timoshenko beam theory. Finally, the derived equations are solved using a numerical method for both simply-supported and clamped boundary conditions. The parametric study is performed to study the effects of different parameters such as axial and radial FG power indexes, porosity parameter, nonlocal gradient strain parameters on the buckling behavior of di-dimensional functionally graded porous tube.

• Structural Engineering and Mechanics
• /
• 제68권2호
• /
• pp.203-213
• /
• 2018

This paper presents a study of geometric nonlinear forced vibration of carbon nano-tubes (CNTs) reinforcement composite plates on nonlinear elastic foundations. The plate is bonded with piezoelectric layers. The von Karman geometric nonlinearity assumptions with classical plate theory are employed to obtain the governing equations. The Galerkin and homotopy perturbation method (HPM) are utilized to investigate the effect of carbon nano-tubes volume fractions, large amplitude vibrations, elastic foundation parameters, piezoelectric applied voltage on frequency ratio and primary resonance. The results indicate that the carbon nano-tube volume fraction, applied voltage and elastic foundation parameters have significant effect on the hardening response of carbon nanotubes reinforced composite (CNTRC) plates.

• 한국응용과학기술학회지
• /
• 제34권3호
• /
• pp.595-601
• /
• 2017

In vivo assay of glucose detection was described using a skin tattoo film electrode (STF), and the probe was made from carbon nano tube paste modification film paper. Here in the square-wave stripping anodic working range obtained of $20-100mgL^{-1}$ within an accumulation time of 0 seconds only in sea water electrolyte solutions of pH 7.0. The relative standard deviations of 50 mg glucose that were observed of 0.14 % (n=12), respectively, using optimum stripping accumulation of 30 sec, the low detection limit (S/N) was pegged at 15.8 mg/L. The developed results can be applied to the detect of in vivo skin sensing in real time. Which confirms the results are usable for in vitro or vivo diagnostic clinical analysis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.211-212
• /
• 2005

Semiconductor fabrication technique has been increasingly developed virtue of greater demands, and supplies and applied semiconductor components in respective processes under development for minuteness. Now semiconductor having a line-width of 75nm was commercialized, and it is possible to scale down to 25nm. Accordingly, to cover with limitations, alternatives are actively investigated. In this paper, we overview the trend and applications of carbon nano tube (CNT) and present the future and technology based on existed theories.

• 한국응용과학기술학회지
• /
• 제31권4호
• /
• pp.679-687
• /
• 2014

본 연구에서는 캐비테이션에 의한 부식에 강한 도료를 개발하기 위하여 고탄성의 우레탄 수지에 내마모 성능을 향상시키기 위한 첨가제로서 Multi wall과 Single wall type의 Carbon nano tube(CNT)와 Spherical과 Fiber type의 Graphite 나노 입자를 첨가하여 물성과 캐비테이션에 대한 저항성, 작업성 등을 비교 평가하였다. 나노 입자로서 Graphite에서는 캐비테이션 저항성($t_{50}$)이 Spherical type($t_{50}$ 182min)보다는 Fiber type($t_{50}$ 292min)이 높은 캐비테이션 저항성을 갖는 것으로 관찰되었다. 또한 CNT에서는 Single wall type의 캐비테이션 저항성($t_{50}$ 286min)이 Multi wall보다는 더 높은 것으로 관찰되었다. 나노 입자중에서 가격 및 캐비테이션 저항성을 감안하면 가장 최적의 나노 입자는 Fiber type의 Graphite로 관찰되었다. 도료의 작업성 평가에서 수동 작업에 의해 제작된 표면은 매끈한 표면을 가지고 있으나 Spray 작업에 의해 제작된 표면은 표면이 균일하지 않으며 Spray시 발생된 Dust가 표면에 고착된 형태로 관찰되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.415-415
• /
• 2012

ZnO nanostructures were synthesized by a vapor phase transport process in a single-zone furnace within a horizontal quartz tube with an inner diameter of 38 mm and a length of 485 mm. The ZnO nanostructures were grown on Au-catalyzed Si(100) substrates by using a mixture of zinc oxide and graphite powders. The growth of ZnO nanostructures was conducted at $800^{\circ}C$ for 30 min. High-purity Ar and $O_2$ gases were pushed through the quartz tube during the process at a flow rate of 100 and 10 sccm, respectively. The sequence of ON/OFF cycles of the Ar gas flow was repeated, while the $O_2$ flow is kept constant during the growth time. The Ar gas flow was ON for 1 min/cycle and that was OFF for 2 min/cycle. The structure and optical properties of the ZnO nanostructures were investigated by field-emission scanning electron microscope, X-ray diffraction, temperature-dependent photoluminescence. The preferred orientation of the ZnO nanostructures was along c-axis with hexagonal wurtzite structure.

• 한국정밀공학회지
• /
• 제22권9호
• /
• pp.49-59
• /
• 2005

This paper describes a development of the extrusion process and estimation of the weldability for multi cell tubes used to cooling system of automobiles. A study on extrusion process is performed through the 3D FE simulation in non-steady state and extrusion experimentation. Also, nano-indentation test is employed to estimate the weldability of tubes. Especially, An evaluation of the weldability using the nano-indentation is accomplished as compared with nano-hardness in welded part and in the others. Finally, the pattern of the mandrel defection is investigated according to shapes of the porthole and/or chamber.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.867-869
• /
• 2003

Vacuum tube arrays (VTA) with a submicron dimension were fabricated by using anodic aluminum oxide (AAO) nano-templates. The field emission characteristics of Ni nanowires show a turn-on voltage in the range of 11.0-14.0 V and a field enhancement factor in the range of 560-2790. The distance between the tips of Ni nanowires and the anode was much smaller than that between the tips and the anode of conventional designs.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2005년도 추계학술강연 및 발표대회강연 및 발표논문 초록집
• /
• pp.100-101
• /
• 2005