• 한국세라믹학회지
• /
• 제31권10호
• /
• pp.1089-1098
• /
• 1994

The effect of Si3N4 addition on the microstructure and PTCR characteristics of BaTiO3 was studied. When 0.1 mol% Sb2O3-doped BaTiO3 codoped with Si3N4 (0.1, 0.25, 0.5, 0.75, and 1 wt%, respectively) were sintered, their microstructures were changed by the amount of the liquid phase as a result of eutectic reaction at 126$0^{\circ}C$. By these microstructural changes, the specific resistivity ratio($\rho$max/$\rho$min) with Si3N4 content variation of 0.1 mol% Sb2O3-doped BaTiO3 ceramics sintered at 130$0^{\circ}C$ for 1 hour varied between 3.70$\times$102(0.1 wt% Si3N4) to 1.16$\times$103 (1wt% Si3N4).

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.386-391
• /
• 2000

It is known that Si$_3$N$_4$ceramic insert has less hardness than A1$_2$O$_3$ceramic insert. But Si$_3$N$_4$ceramic insert has not only high toughness and strength but also low thermal expansion coefficient, which makes it has longer tool life under thermal stress condition. In this study, commercial Si$_3$N$_4$ ceramic insert and home-made SiC-Si$_3$N$_4$ceramic insert which has different sintering time and chemical composition is tested under various cutting conditions. The experimental result is compared in terms of tool life and cutting force. Generally, As the cutting speed and the feed rate increased, the cutting force and the flank wear increased too. The performance of SiC-Si$_3$N$_4$ceramic insert shows the possibility to be a new ceramic tool.

• 한국분말재료학회지
• /
• 제8권3호
• /
• pp.174-178
• /
• 2001

The microstructure and mechanical properties of $Si_3N_4/BN $nanocomposites synthesized by chemical processing were investigated. The nanocomposites containing 15 vol% hexagonal BN (h-BN) were fabricated by hot-pressing $\alpha-Si_3N_4$powders covered with turbostratic BN (t-BN). The t-BN coating on $\alpha-Si_3N_4$particles was prepared by heating $\alpha-Si_3N_4$ particles covered with a mixture of boric acid and urea in hydrogen gas. TEM observations of this nanocomposite revealed that nano-sized h-BN particles were homogeneously dispersed within $Si_3N_4$grains as well as at grain boundaries. The strength and thermal shock resistance were significantly improved in comparison with the $Si_3N_4/BN$ microcomposites.

• 한국세라믹학회지
• /
• 제31권9호
• /
• pp.1021-1029
• /
• 1994

SiC ultrafine particles of 1, 10, 20 and 30 vol% were dispersed in $\alpha$-Si3N4 matrix and hot-pressed under the condition of 30 MPa at 1800 and 190$0^{\circ}C$ respectively. Physical, mechanical properties and microstructures of sintered Si3N4-SiC nanocomposites were investigated. Flexural strength and density of Si3N4-10 vol% SiC nanocomposites hot-pressed at 190$0^{\circ}C$ represented the 1002 MPa and 97.9%T.D respectively, and it was confirmed as a remarkable improvement of 67% compared to Si3N4 monolith. Fracture toughness was shown as 7.2 MPa.m1/2 when the same composition was hot pressed at 180$0^{\circ}C$. This effect was supposed to be due to the improvement of microstructure by the adequate suppression of the excessive growth of Si3N4 grain with SiC nano-particles.

• 한국세라믹학회지
• /
• 제30권12호
• /
• pp.999-1006
• /
• 1993

Si3N4(p)-SiC(p) composites were prepared by gas pressure sintering at 190$0^{\circ}C$ for 1 hour. $\alpha$-SiC with average particle size of 0.48${\mu}{\textrm}{m}$ were dispersed from zero to 50vol% in $\alpha$-Si3N4 with average particle size of 0.5${\mu}{\textrm}{m}$. Y2O3-Al2O3 system was used as sintering aids. When 10vol% of SiC was added to Si3N4, optimum mechanical properties were observed; relative density of 98.8%, flextural strength of 930MPa, fracture toughness of 5.9MPa.m1/2 and hardness value of 1429kg/$\textrm{mm}^2$. Grain growth of $\beta$-Si3N4 was inhibited as the amount of added SiC was increased. SiC particles were found inside the $\beta$-Si3N4 intragrains in case of 10, 20 and 30vol%SiC added composites.

• 한국세라믹학회지
• /
• 제25권6호
• /
• pp.615-622
• /
• 1988

To develope good slip and microstructure of Si3N4 the knowledge of the interaction of particles in liquid systems is required. In this work polyethyleneimines was tested as a stabilizer for Si3N4-water system. The stability of slip dispersed with polyethyleneimines was good over a wide range of pH and concentrated slips with low viscosity could be cast. This work comprises a systematic investigation including determination of electrical mobility in order to estimate the particle surface charge, determination of sedimentation rate, as well as measurements of the viscosity as a function of dispersants, pH and shear rates. The influence of deflocculation on the microstructure of slip cast Si3N4 was discussed.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2004년도 춘계학술대회 발표 논문집
• /
• pp.67-71
• /
• 2004

400~450nm 파장 범위의 청색광을 검출하는 Si 포토다이오드에서 $SiO_2$, $Si_{3}N_{4}$, $SiO_{2}/Si_{3}N_{4}$를 광반사 방지막으로 사용하는 경우 광반사 방지막의 두께에 따른 표면 광반사 손실을 이론적으로 계산하였다. 400~450nm 청색 파장에서 $SiO_2$, $Si_{3}N_{4}$ 단일막에 대한 최소 광반사 손실은 각각 $d(SiO_2)=700~750{\AA}$ 와 $d(Si_{3}N_{4})=500${\AA}$에서 나타났으며, $SiO_{2}/Si_{3}N_{4}$ 이중막에 대한 최소 광반사 손실은 $d(SiO_{2}/Si_{3}N_{4})=750{\AA}/(180~200){\AA}$에서 나타났다.

• 수산해양기술연구
• /
• 제14권2호
• /
• pp.79-87
• /
• 1978

기관밸브용접 SCr4-21-4N 및 SUH3-21-4N을 연구선정된 최적마찰압접조건 하에서 마찰압접을 하고 이때 생기는 압접부의 잔류응력 및 경도의 peak 등 압접결함의 제거 및 압접성능개선을 위한 열처리에 관하여 실험연구한 결과 다음과 같은 결론을 얻었다. (1) 배기 valve용강 SCr4-21-4N 및 SUH3-21-4N의 마찰압접을 위한 최적조건으로서 회전수 3,000rpm, 마찰가열압 p 하(1)=8 kg/mm 상(2), upset 압 p 하(2)=20 kg/mm 상(2), 압접가열시간 t 하(1)=3초, upset 시간 2.5초를 선정한 것이 매우 타당함이 실험적으로 입증되었다. (2) 이종재질 SUH3-SUH31, SCr4-SUH31, SCr4-SUH3, SUH3-CRK22, SCr4-21-4N 및 SUH3-21-4N의 마찰압접에 관한 저자의 종래 연구와 본연구 결과는 압접부의 압접 특성이 서로 매우 일치하였다. (3) SCr4-21-4N 및 SUH3-21-4N의 마찰압접부의 잔류응력 및 전도의 peak를 제거하기 위한 최적열처리조건은 $600^{\circ}C$$\times$30min.$\times$room air cooling의 normalizing임이 확인되었다. (4) 이때 열처리 후에는, 열처리전의 인장강도의 약 20%가 감소했으나, 파단 위치는 열영향부로부터 모재 SCr4 및 SUH3 측으로 이동하였다. (5) 상기 최적조건 하에서 마찰압접되고 열처리된 압접부의 현미경 조직검사 결과, 압접부가 매우 좁고 압접결함이 없으며, 치밀하고 조밀한 조직의 우수한 압접이었음이 확인되었다. (6) 상기 최적조건은, 기관 valve 생산을 위한 타이종재질의 마찰압접조건으로도 응용될 수 있을 것이다.

• 대한치과보철학회지
• /
• 제44권6호
• /
• pp.740-750
• /
• 2006

Statement of problems. In an attempt to reduce screw loosening, dry lubricant coatings such as pure gold or tefron have been applied to the abutment screw. However, under repeated tightening and loosening procedures, low wear resistance and adhesion strength of coating material produced free particles on the surface of abutment screw and increased frictional resistance resulting in screw tightening problems. Purpose. The aim of this study was to compare friction coefficient, adhesion strength, vickers hardness and evaluate coating surface of titanium alloy specimens coated with TiN(titanium nitride), ZrN(zirconium nitride) and WC(tungsten carbide). Material and method. Titanium alloy(Ti-6Al-4V) discs of 12mm in diameter and 1mm in thickness divided into 4 groups. TiN, ZrN and WC was coated for the specimens of 3 groups respectively, and those of 1 group were not coated. Each group was made up of 4 specimens. In this study, sputtering method was used among the PVD(Physical Vapor Deposition) techniques available for TiN, ZrN and WC coatings. Friction coefficient, adhesion strength, vickers hardness and coating surface of 4 groups were measured. Results. 1. For all three coating conditions, friction coefficient was significantly decreased. Especially, ZrN coated surface showed the lowest value. $TiN(0.39{\pm}0.02)$, $ZrN(0.24{\pm}0.01)$, $WC(0.31{\pm}0.03)$. 2. TiN coating showed the highest adhesion strength, however ZrN coating had the lowest value. $TiN(25.3N{\pm}1.6)$, $ZrN(14.8N{\pm}0.6)$, $ WC(18.4N{\pm}0.7)$. 3. Vickers hardness of all three coatings was remarkably increased as compared with that of none coated specimen. TiN coating had the highest Vickers hardness, however WC coating showed the lowest value. $TiN(1865.2{\pm}33.8)$, $ZrN(1814.4{\pm}18.6)$, $WC(1008.5{\pm}35.9)$. 4. The ZrN or WC coated specimen showed a homogeneous and smooth surface, however the rough surface with defects was observed for TiN coating. Conclusions. When TiN, ZrN and WC coating applied to the abutment screw, frictional resistance would be reduced, as a result, the greater preload and prevention of the screw loosening could be expected.

• 한국재료학회지
• /
• 제8권10호
• /
• pp.890-897
• /
• 1998

n-InP(001)기판과 PECVD법으로 ${Si}_3N_4$(200nm)막이 성장된 InP 기판사이의 direct wafer bonding을 분석하였다. 두 기판을 접촉시켰을 때 이들 사이의 결합력에 크게 영향을 주는 표면 상태를 접촉각 측정과 AFM을 통해서 분석하였다. InP 기판은 $50{\%}$ 불산용액으로 에칭하였을 때 접촉각이 $5^{\circ}$, RMS roughness는 $1.54{\AA}$이었다. ${Si}_3N_4$는 암모니아수 용액으로 에칭하였을 때 RMS roughness가 $3.11{\AA}$이었다. Inp 기판과 ${Si}_3N_4$/InP를 각각 $50{\%}$ 불산 용액과 암모니아수 용액에 에칭한 후 접촉시켰을 때 상당한 크기의 초기 겹합력을 관찰할 수 있었다. 기계적으로 결합된 시편을 $580^{\circ}C$-$680^{\circ}C$, 1시간동안 수소 분위기와 질소분우기에서 열처리하였다. SAT(Scanning Acoustic Tomography)측정으로 두 기판 사이의 결합여부를 확인하였다. shear force로 측정한 InP 기판과 ${Si}_3N_4$/InP사이의 결합력은 ${Si}_3N_4$/InP 계면의 결합력만큼 증가되었다. TEM과 AES를 이용해서 di-rect water bonding 계면과 PECVD계면을 분석하였다.