• Corrosion Science and Technology
• /
• v.16 no.3
• /
• pp.100-108
• /
• 2017

In this investigation corrosion behavior of newly developed high-pressure die cast Al-Ni (N15) and Al-Ni-Ca (NX1503) alloys was studied in 3.5% NaCl solution. The electrochemical corrosion behavior was evaluated using open circuit potential (OCP) measurement, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. Potentiodynamic polarization results validated that NX1503 alloy exhibited lower corrosion current density ($i_{corr}$) value ($5.969{\mu}A/cm^2$) compared to N15 ($7.387{\mu}A/cm^2$). EIS-Bode plots revealed a higher impedance (${\mid}Z{\mid}$) value and maximum phase angle value for NX1503 than N15 alloy. Equivalent circuit curve fitting analysis revealed that surface layer ($R_1$) and charge transfer resistance ($R_{ct}$) values of NX1503 alloy was higher compared to N15 alloy. Immersion corrosion studies were also conducted for alloys using fishing line specimen arrangement to simultaneously measure corrosion rates from weight loss ($P_W$) and hydrogen volume ($P_H$) after 72 hours and NX1503 alloy had lower corrosion rate compared to N15 alloy. The addition of Ca to N15 alloy significantly reduced the Al3Ni intermetallic phase and further grain refinement may be attributed for reduction in the corrosion rate.

• Korean Journal of Materials Research
• /
• v.30 no.5
• /
• pp.262-266
• /
• 2020

In this paper, we investigated the effect of the passivation stack with Al₂O₃, hydrogenated silicon nitride (SiN_x:H) stack and Al₂O₃, silicon oxynitride (SiON_x) stack in the n type bifacial solar cell on monocrystalline silicon. SiNx:H and SiON_x films were deposited by plasma enhanced chemical vapor deposition on the Al₂O₃ thin film deposited by thermal atomic layer deposition. We focus on passivation properties of the two stack structure after laser ablation process in order to improve bifaciality of the cell. Our results showed SiN_x:H with Al₂O₃ stack is 10 mV higher in implied open circuit voltage and 60 ㎲ higher in minority carrier lifetime than SiON_x with Al₂O₃ stack at Ni silicide formation temperature for 1.8% open area ratio. This can be explained by hydrogen passivation at the Al₂O₃/Si interface and Al₂O₃ layer of laser damaged area during annealing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.300-300
• /
• 2010

후면 패시베이션, back contact의 가변, 후면 접촉면적의 가변 등으로 Laser Fired Contact 태양전지의 효율을 증가 시킬 수 있다. 이 중 spacing의 가변으로 후면 접촉 면적을 가변 할 수 있으며, 이로 인하여 LFC 태양 전지의 효율을 높일 수 있을 것으로 전망된다. 본 연구에서는 후면 접촉 면적을 가변하였으며 이에 따른 효과를 확인하였다. series resistance가 작고, open circuit voltage 가 높은 최적의 조건을 찾는 것에 그 목적을 두었다. 실험 순서는 texturing 후, 후면에 SiNx를 10nm 증착하였으며, drive-in 방법으로 $POCl_3$을 도핑하였다. ARC후, spacing 조건 가변으로 접촉 면적을 가변시키면서 소자의 특성 변화를 비교하였다. 접촉 면적 및 spacing 조건은 5개의 set에 대하여 reference, 50%의 접촉 면적을 가지는 $150{\mu}m$ line, 10%의 접촉 면적을 가지는 $700{\mu}m$ line, 1%의 접촉 면적을 가지는 $700{\mu}m$ dot, 그리고 0.2%의 접촉 면적을 가지는 $1500{\mu}m$ dot으로 하였다. 각각의 경우에 대한 short circuit current density, fill factor, seris resistance, sheet resistance, open circuit voltage를 측정하였으며, 특히 series resistance는 각각의 경우에 대하여 $6.1m{\Omega}$, $5.1m{\Omega}$, $7.8m{\Omega}$, $10.1m{\Omega}$, 그리고 $15.7m{\Omega}$으로 측정되었다. wafer의 외각 테두리를 접촉 면적이 증가함에 따라서 sheet resistance가 증가하는 것을 확인 할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.470.2-470.2
• /
• 2014

RF-PECVD 장치에 의해 증착된 실리콘 질화막(SiNx)은 결정질 실리콘 태양전지에서 반사 방지막 효과 및 우수한 표면 패시베이션 특성을 제공하는 것으로 알려져 있다. 본 논문에서는 실리콘 질화막의 패시베이션 특성을 향상시키기 위해서 공정온도를 $400^{\circ}C$로 고정하고 공정압력, 가스비, RF (radio frequency) power를 가변하였다. 이 때의 실리콘 질화막의 굴절률 및 두께는 각각 2.0, 80 nm로 증착하여 그에 따른 특성에 대해 분석하였다. 공정 압력이 감소할수록 실리콘 질화막이 증착된 결정질 실리콘 태양전지의 유효 반송자 수명이 증가함을 보였고, 반면에 증착속도는 감소하였다. 또한 RF-power 500 W에서 실리콘 질화막이 증착된 결정질 실리콘 태양전지의 유효 반송자 수명이 상대적으로 높았으며 출력이 올라갈수록 증착속도가 증가하였다. 결과적으로 결정질 실리콘 태양전지에 증착한 실리콘 질화막은 0.8torr 공정 압력과 RF-power 500 W에서 $38.8{\mu}s$로 가장 좋은 유효 반송자 수명을 확인하였다. 위의 결과를 바탕으로 결정질 실리콘 태양전지를 제작하였고 향상된 패시베이션 특성을 갖는 실리콘 질화막의 조건을 찾기 위해서 개방전압(open circuit voltage)을 비교하였다. 공정압력 0.8 torr, RF-power 500 W에서 가장 높은 결과를 보였으며 이는 유효 반송자 수명과 유사한 결과를 나타냈다. 하지만 낮은 FF (fill factor)로 인해 변환 효율이 낮은 결과를 보였다. 태양전지 제작시 낮은 fill factor를 보인 이유와 위의 단점을 보완하기 위해 추가 실험을 수행하였으며, 개선된 fill factor를 통해 18.3% 효율의 태양전지를 제작하였다.

• Korean Journal of Computational Design and Engineering
• /
• v.20 no.2
• /
• pp.104-113
• /
• 2015

In developing a tire, many CAE analyses are performed to make a better tire. But its meshing work is not easy, and it takes much time. One of the reasons of taking much time is that there are many overlapped geometric entities in CAD data that are modeled in CAD system by CAD engineers. In this study, we studied about the features of the overlapped geometric entities, and the method to find out and delete them. I developed a program using the proposed algorithm, and applied it in meshing tire pattern and tire case. I proved that the time in meshing a tire reduced dramatically by removing overlapped geometric entities by using the developed program.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.243-243
• /
• 2010

This paper two different etching, HF : HNO3 :DI and RIE were used for etching in multi-crystalline Silicon(Mc-Si) solar cell fabrication. The wafers etched in RIE texture showed low reflectance compared to the wafers etched in Acid soultion after SiNx deposition. In light current-voltage results, the cells etched in RIE texture exhibited higher short circuit current and open circuit voltage than those of the cells etched in acid solution. We have obtained 15.1% conversion efficiency in large area($156cm^2$) Multi-Si solar cells etched in RIE texture.

• The Journal of Engineering Geology
• /
• v.4 no.1
• /
• pp.13-28
• /
• 1994

Hydrogeologic characteristics of crystalline rock including discontinuities is defined by the hydraulic data from the in situ test and by analytical method. Methodology and procedure of the in situ test are used in accordance with test purpose, site condition and characteristics of host rock Hydraulic conductivities in crystalline rock including discontinuifies such as fractured zone and joint, are defined by packer test and slug test. The results indicate Hvorslev' s theory of ground water flow in NX borehole, that the shorter of test interval is, the higher hydraulic conductivity is. This is an indicafion of the fact that the hydraulic rneasured were governed by scale effect of test interval, even at same borehole. According to the result of packer tests in two boreholes, it is understood that hydraulic conductivifies show variations according to the effect of as order of tests. In the comparison of hydraulic conductivifies from both of open borehole tests, the results are relatively well correrated in values. The hydraulic conductivity in the test intervals induding hydrogeologically significant discontinuity shows relatively higher value of hydraulic conductivity in vertical distribution of full depth.