• 한국대기환경학회지
• /
• 제22권4호
• /
• pp.440-450
• /
• 2006

PM10, NOx, and $O_3$ were measured at six locations, of which each three is horizontally and vertically distributed respectively, in an apartment complex around the heavily traffic road. Those were measured seven times a day with two hours interval starting from 8 o'clock in the morning for 15 days during May 2005 $\sim$ September 2005. PM10 and NOx showed high concentrations in rush hours while low concentrations in midday due to the direct emissions from automobiles in operation. Temporal variations of 01 showed very much similar trend appeared in normal urban atmospheres. The spatial distributions of PM10, NOx and $O_3$ showed that almost all of concentrations were higher in a row of Roadside > Surface at 130 m apart from the road > Surface at 230 m apart from the road > 3rd floor of apartment building > 15th floor of apartment building > 27th floor of apartment building. Model equations, which can project spatial concentration distributions, were constructed by combining the horizontal and the vertical linear regression equations derived from six mean values corresponding to six measuring locations. According to inter-comparison of PM10, NOx, and $O_3$ with the constructed model equations, concentration gradients were higher in a row of Vertical direction of NOx > Vertical direction of PM10 > Horizontal direction of NOx > Horizontal direction of PMIO > Vertical direction of $O_3$ > Horizontal direction of $O_3$. Why concentration gradient of particulate PM10 is lower than that of gaseous NOx is in question, and should be studied.

• 한국전기전자재료학회논문지
• /
• 제26권4호
• /
• pp.325-329
• /
• 2013

Carbon nanotubes(CNT) have excellent electrical, chemical stability and mechanical properties. These can be used in a variety of fields. MWCNT are extremely sensitive for minute changes in the ambient gas, namely, their sensing properties varies greatly with the absorption of gas such as NOx and $H_2$. We investigate the electrical properties of CNTs and make a NOx gas sensor based on Multi-walled carbon nanotubes (MWCNT) materials. We obtained the NOx gas sensor of MWCNT based on P-type Si wafer that has the resistivity of $1.667{\times}10^{-1}[{\Omega}{\cdot}cm]$. We knew that the sensitivity of sensor decreased with increasing of NOx gas concentration. And the sensitivity of sensor shows the largest value at $20^{\circ}C$. The sensitivity of sensor decrease with increasing the temperature. Also absorption energy of NOx gas molecule on the MWCNT surface decreases with increasing concentration of NOx gas.

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.75-81
• /
• 2003

In this paper, the study of effects of flow variables on flame structure and NOx emission concentration was performed in co-axial laminar partially premixed methane/air flames. the objectives are to reveal its effect as parameters were varied and to understand the correlation between flame structure and NOx emission characteristics in the reaction zone. equivalence ratio(${\Phi}$), fuel split degree(${\sigma}$), and mixing distance(x/D) were defined as a premixing degree and varied within $1.36{\sim}3.17$(equivalence ratio), $50{\sim}100$(fuel split degree), and $5{\sim}20$(mixing distance). the image of $OH{\ast}$ and $CH{\ast}$, and NOx concentration were obtained with an ICCD camera and a NOx analyzer. additionally the maximum intensity location of $OH{\ast}$ chemiluminescence and $CH{\ast}$ chemiluminescence were measured to compare each flame structures. In conclusion flame structure and NOx emission characteristics were changed from diffused to premixed flame when mixing degree was on the increase. the main effect on flame structure and NOx production was at first equivalence ratio(${\Phi}$), and next fuel split degree(${\sigma}$), and finally mixing distance(x/D).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.922-926
• /
• 2002

In this paper, in order to investigate the catalytic effect of the sludge exhausted from waterworks as heating temperature for NOx removal, we measure NO, $NO_2$ concentration as increasing temperature of sludge pellets and applying high voltage to sludge pellets in a quartz-glass reactor at the same time. NO initial concentration is 100ppm balanced with air gas in a mixing chamber. The gas flow is 5[l/min] and the heating temperature of sludge pellets in a quartz-glass reactor is adjusted from $200[^{\circ}C]$ $400[^{\circ}C]$ to investigate the effect of sludge pellets for removal NOx$(NO+NO_2)$ as increasing temperature. $BaTiO_3$ pellets is filled in a packed-bed reactor for corona discharge to measure how much NOx$(NO+NO_2)$ is removed after generating $NO_2$ from the packed-bed reactor. AC[60Hz] voltage is supplied to the reactor for discharge. In the result, $NO_2$ concentration is decreased by sludge pellets without heating temperature for sludge pellets in case of sludge pellets done heat treatment, however NO concentration is almost the same to be compared NO initial concentration. As increasing heating temperature for sludge pellets, $NO_2$ adsorbed on the sludge surface done heat treatment is converted to NO by the thermal energy, so NO concentration is extremely increased by reduction decomposition of $NO_2$. Finally, We think the sludge is possible to use for reduction catalysts, however we need to study more about the possibility and endurance of sludge as catalysts for NOx removal.

• 한국자동차공학회논문집
• /
• 제3권1호
• /
• pp.76-88
• /
• 1995

The effects of exhaust gas recirculation(EGR) on the characteristics of NOx emissions and specific fuel consumption rate have been investigated using an eight-cylinder. four cycle. direct injection diesel engine operating at several loads and speeds. The theoretical NO formation concentration is calculated with the equivalence ratio as a parameter of flame temperature to study the effect of EGR on NOx emissions in the diesel combustion. The experiments in this study are conducted on the fixed fuel injection timing of $38^{\circ}$ BTDC regardless of experimental conditions. It is found that the specific fuel consumption rate is slightly increased with EGR rate. and NOx emissions are markedly reduced owing to the drop of the incoming oxygen concentratio and the increase of equivalence ratio as the EGR rate increases.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.71-76
• /
• 2003

A numerical simulation of selective catalytic reduction (SCR) for NO with $NH_3$ is conducted over the $V_2O_5/TiO_2$ and $WO_3-V_2O_5/TiO_2$ catalysts. The governing $NH_3$ and NO transport equations are considered by using the time-dependent FCT (Flux-Corrected Transport) algorithm. After a validating simulation for $NH_3$ step feed and shut-off experiments is analyzed, transient behavior of $NH_3$ and NO concentration in a SCR catalyst is investigated by changing such parameters as inflow $NH_3$ concentration, temperature of the catalyst, and $NH_3$/NOx ratios.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권8호
• /
• pp.807-811
• /
• 1997

In this paper we have investigated the removal characteristics of NOx by pulsed corona discharge with a multi-pointplane electrode where a magnetic field is applied in the discharge region. The efficiency of NOx removal was measured and analyzed as a function of pulse frequency gas flow rate NOx initial concentration magnetic flux density. In this result the highest removal efficiency of NOx was obtained at the following operating conditions; the frequency =400[Hz] gas flow =1[$\ell$/min] initial concentration= 400[ppm] and magnetic flux density=0.36[T].

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권2호
• /
• pp.248-255
• /
• 2002

Miller cycle was studied and analyzed by engine performance simulation to achieve very low fuel consumption and to meet the IMO NOx regulation on a medium speed diesel engine. Based on the performance simulation results the intake valve closing time for HYUNDAI HiMSEN 6H21/32 engine was set at 0deg.ABDC(After Bottom Dead Center). Also, the simulation results indicated that significant NOx reduction could be achieved with low reduction of fuel consumption. The performance simulation investigated the effect of compression ratio and turbocharger on fuel consumption and NOx concentration in combination with Miller cycle. The results indicated a significant reduction of fuel consumption with keeping NOx concentration. The results of performance simulation were compared with measured data to verify simulation results. The comparison showed the maximum error was 2.34% in exhaust temperature. Also, the experimental result showed that improvement in BSFC(Brake Specific Fuel Consumption) was 5.8g/kwh with keeping NOx level similar to simulation result.

• 유기물자원화
• /
• 제18권1호
• /
• pp.66-72
• /
• 2010

본 연구는 경기도 A지역 자원회수시설에서 연소온도의 변화에 따른 NOx, SOx, CO, HCL, DUST의 발생변화와 보일러 배출가스 온도, 보일러 출구산소 농도, 반건식 반응탑 출구온도, 촉매탑온도, 배출가스 온도의 변화를 분석하였다. SOx, CO, Hcl, DUST는 자원회수시설 내의 연소온도가 상승함에 따라 거의 5 ppm 미만의 일정한 값을 유지한 반면 NOx 는 40 ppm에서 70 ppm으로 증가하는 추세였다. 한편 보일러 배출가스 온도와 촉매탑 온도는 일정치를 유지하였으나 보일러 출구의 산소농도는 조금씩 감소하는 결과를 나타내었다.

• 한국대기환경학회지
• /
• 제20권5호
• /
• pp.615-623
• /
• 2004

This study was conducted for developing the emission factors of nitrogen oxide(NOx) and carbon monoxide (CO) from the combustion boilers burning liquefied natural gas (LNG). These emission factors were compared with those of U.S. EPA and European Environment Agency (EEA). NOx and CO concentration in the flow gas were measured using Kane-May, KM9106 and Thermo Environmental Instruments Inc., 42C-HL. Measurement were conducted at thirty industrial and commercial LNG boilers. Emission factors were calculated on the basis of fuel consumption (kg-pollutant/㎥-fuel burned). NOx concentration at industrial boiler was 14~125 ppm and it was measured as 35~125 ppm at commercial boiler. NOx emission factors of industrial boiler and commercial boiler were 1.84kg/$m^3$ and 2.09kg/$m^3$, respectively. NOx emission factor of commercial boiler was higher than that of industrial boiler. The NOx emission factors estimated in this study were lower than those of U.S. EPA and higher than those of EEA. Average CO emission factor of industrial boiler was 0.65 kg/$m^3$ and at commercial boiler it was 0.70kg/$m^3$, CO emission factor at industrial boiler was lower than that at commercial boiler.