• Membrane Journal
• /
• v.6 no.3
• /
• pp.157-165
• /
• 1996

Polysulfone(PS) membranes were prepared from homogeneous PS solutions by the phase inversion technique. When propionic acid(PA) was added into a casting solution of n-methylpyrrolidone(NMP) and PS, precipitation rate of the solution film was accelerated. This kind of acceleration was consistent, even though a precipitating nonsolvent was changed from water to isopropanol. These phenomena were caused by decrease of nonsolvent tolerance in the casting solution due to addition of PA. PS powder was prepared by precipitation of a 3wt% solution in dimethylformamide(DMF) using ethanol as nonsolvent. Gas adsorption analysis of the powder showed that the capillary condensation sites were found in the powder structure. Membranes prepared from PS solution(15wt%) in NMP had the following characteristics of gas adsorption and water permeation. In gas adsorption analysis, the membrane precipitated using isopropanol showed low uptake of nitrogen gas and the capillary condensation sites were not found. On the contrary, a significant amount of the capillary condensation sites was found in the membrane coagulated by water, which was related to increase of nitrogen uptake. tn the membrane prepared froin the solution including PA, an increase of the Henry's law sites and the Langmuir sites was not found clearly. However, the capillary condensation sites were significantly increased, and the water transport also increased.

• Membrane Journal
• /
• v.17 no.3
• /
• pp.219-232
• /
• 2007

The polyethersulfone(PES)-titanium oxide($TiO_2$) hybrid membranes were prepared by immersion precipitation phase inversion method. The casting solution for the preparation of $PES-TiO_2$ hybrid membrane was provided by adding $TiO_2$ nano particles into the basis polymer solution of 14 wt% and 20 wt% PES/N-methyl-2-pyrrolidone(NMP). The $TiO_2$ loading [wt% ($TiO_2/NMP$)] in eating solution was varied from 0 to 60 wt%. Membrane performance and morphological change of the resulting $PES-TiO_2$ hybrid membranes were discussed in aspect of $TiO_2$ loading, by viscosity, coagulation value and light transmittance of the casting solution, measurement of tensile strength, pore size and contact angle, surface and cross sectional SEM images of the hybrid membrane, and ultrafiltration experiments using the hybrid membrane. According as increase of $TiO_2$ loading in the casting solution, viscosity is increased and coagulation value becomes lower, therefore the thermodynamic instability of the casting solution is increased. It is found that when $TiO_2$ loading is increased, 1) precipitation rate becomes faster while instantaneous demixing is maintained, 2) pure water flux, membrane pore size and compaction stability of the resulting membranes are increased, 3) tensile strength and contact angle are decreased. Dead-end ultrafiltration of bovine serum albumin(BSA) solution using the hybrid membrane shows that membrane performance(flux of BSA solution) enhanced up to 7 times compared with the results obtained using the pure PES membrane(not containing $TiO_2$ particle), due to the increase of hydrophilicity.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1996.04a
• /
• pp.36-37
• /
• 1996

폴리술폰을 이용한 분리막의 제조에 있어서 용매 및 조성의 변화에 따른 상도의 작성은 매우 큰 정보를 제공한다. 즉 상도를 통해서 상분리 현상을 예측할 수 있게 되어서 막의 미세구조를 조절할 수 있게 되고, 막의 미세구조를 조절함으로써 투과 분리 특성을 향상시킬 수 있게 된다. 본 실험에서 사용된 고분자는 폴리술폰(Udel P-3500)이며, 용매로는 NMP와 THF를 사용하였다. 실험적으로 흐림점을 측정하여 binodal line을 얻었으며 문헌값, 계산값, 실험값 등을 통한 interaction parameter 값들로 부터 binodal line과 spinodal line을 구하여 실험값과 비교 하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1038-1039
• /
• 2004

We developed a new photoresist which was composed of polyaniline, uv-curing agent, N-methyl-2- pyrrolidine (NMP) and N-Butyl alcohol (BuOH) as solution. The photoresist is characterized by the capability of being developed in water. We successfully patterned pentacene thin film, which was vulnerable to organic solvent and thus could not be patterned by the conventional photolithography process, with the water soluble photoresist and the minimum feature size was found to be 2um.

• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.279-281
• /
• 1992

In this paper, an LQG/LTR procedure for stable nonminimum phase systems is suggested using predictor scheme. In the method, the performance of the target feedback loop can be easily adjusted and the recovery error is less dependent on the location of NMP zeros than previous methods. The gain and phase margin and the robust ness for modeluncertainty of the suggested control system are obtained.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.208-212
• /
• 1991

LQG/LTR method cannot applied to nonminimum phase plant. In this paper, we present a new approximation method which guaratee the approximation error equal to zero and exact loop transfer recovery. Zero structure of plant and approximated plant are considered in approximation procedure. It is shown that the properties of plant and approximated plant at pole and zero frequency response are exactly same. It is shown by example that the suggested method can avoide the NMP plant constraint arised in designing LQG/LTR.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2010.03a
• /
• pp.79-79
• /
• 2010

In this work a PMTA(poly m-phenylene terephthal amide) polymer was synthesized by using new solvent to produce film composite. This Film composite membrane based on PMTA were prepared with 1,3-phenylenediamine(MPD), terephthaloyl chloride (TPC) and Co-solvent (NMP with added $CaCl_2$) was adopted for synthesize PMTA polymer. A series of synthetic experiments were done, aimed to find the optimum condition of polymerization.

• Elastomers and Composites
• /
• v.58 no.1
• /
• pp.26-31
• /
• 2023

Aromatic diamine containing ortho catenation and methyl group was synthesized from 4-methyl catechol and 4-nitrobenzoyl chloride. Subsequently, a poly(amic acid) was prepared by reacting 4-methyl-1,2-phenylene bis(4-aminobenzoate) with 4,4'-hexafluoroisopropylidenediphthalic anhydride (6FDA). The resulting poly(amic acid) was transformed into a polyimide through chemical imidization. The polyimide formed was soluble in N-methyl-2-pyrrolidone (NMP) and could be cast into a flexible, transparent film. Furthermore, the polyimide exhibited a 5% weight loss at 380 ℃ in the nitrogen atmosphere.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.93-97
• /
• 2010

Polyaniline doped with ionic liquid (1,3-dimethylimidazolium methylsulfate, I-DMS) soluble in polar solvents (NMP, DMSO, DMF, m-cresol etc.) were synthesized by nucleophilic addition. Solubilities of PAN/I-DMS powder in polar solvents were observed in the range of 3~6 wt%/vol., respectively. The electrical conductivities of PAN/I-DMS films appeared in the range of $10^{-2}{\sim}7S/cm$. Polyaniline doped with I-DMS (PAN/I-DMS) showed improved thermal stability and conductivity compared to that of HCl doped polyaniline (PAN/HCl) and dimethylsulfate (DMS) doped polyaniline (PAN/DMS) upon heat treatment at $160^{\circ}C$. These improved conductivity and solubility in organic polar solvents was explained with the interactions between the polar sulfonate group and polar solvents.

• Membrane Journal
• /
• v.26 no.6
• /
• pp.463-469
• /
• 2016

In this research, a new expectation in enhancing the PES (polyethersulfone) polymer phase inversion membrane performances with nanoparticles is proposed by using ZnO. This paper investigated the synthesis of PES phase inversion membranes including ZnO nanoparticles and evaluates the performance of these mixed matrix membranes. The PES-ZnO mixed matrix membranes were fabricated by phase inversion method using the PES-ZnO-NMP(N-methyl-1-pyrrolidone) casting solutions with low ZnO nanoparticles content of 0.375 wt%. The influence of ZnO nanoparticles on the characteristics of PES-ZnO mixed matrix membranes was investigated with scanning electron microscope observations of membrane cross-sections, contact angle measurements, tensile strength measurements, pure water flux measurements and ultrafiltration experiments of BSA solution. Those results showed that the performance advancements in comparison with the pure PES membrane without ZnO in terms of increasing hydrophilicity as well as reducing membrane fouling by adding ZnO nanoparticles even in low concentration.