• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.10
• /
• pp.61-70
• /
• 1996

In this paper, we find the values of near-end crosstalk coefficient in striplines of a FR-4 multilayer PCB by an analytic method and a HSPICE simulation method, and define calcualtion errors in an analytic method and define the application range, and simualte near-end crosstalk coefficients of the FCT (fast CMOS TTL) in complicated striplines by HSPICE and analyze near-en crosstalk coefficients in relation to dielectric thickness and trace spaces of striplines. As a result, we analyze coupling structure of the near-end crosstalk in the coplicated sstriplines that are impedance matched and define a coupling formula of near-end crosstalk coefficients in general complicated striplines. Especially, it is approximated in the layout grade rule.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.115-118
• /
• 2002

This paper presents the design method and performance characteristics of a chip-type quadrature hybrid using LTCC-MLC technology. The design method for a chip-type quadrature hybrid is based on lumped element equivalent circuit of quarter-wave transformer. The chip-type quadrature hybrid was miniaturized to a greater extent using multilayer structure and lumped element. The proposed design method can also reduce the undesirable parasitic effects of the chip-type quadrature hybrid. The proposed chip-type quadrature hybrid was designed and fabricated using the proposed design method and the equivalent circuit model of a quarter-wave transformer. Fabrication and measurement of designed chip-type quadrature hybrid show much smaller size than a conventional distributed quadrature hybrid and a good agreement with simulated results.

• The Korean Journal of Ceramics
• /
• v.4 no.1
• /
• pp.43-46
• /
• 1998

We have investigated the formation and thermal stability of cobalt aluminide(CoAl) thin films on GaAs. In order to obtain cobalt-aluminide thin films, we deposited a multilayer of Co/Al on GaAs, and subsequently annealed the samples at 80$0^{\circ}C$ for 30 min. After annealing, single-phase cobalt aluminide was produced showing a flat and uniform interface with GaAs. which indicates that cobalt aluminide (CoAl) is thermally stable with GaAs. In addition, the adherence and mechanical properties of the as-deposited, and annealed Co/Al multilayer structure on GaAs are compatible with those required for device fabrication processes. The electrical property of the CoAl/GaAs contact shows rectifying characteristics, indicating that the diodes were usable as rectifying gate electrodes.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.07a
• /
• pp.237-238
• /
• 2007

A new strain analysis model, so called the stress matched model, in an epitaxial multilayer system is proposed. The model makes it possible to know the strain, the stress, the elastic strain energy in each epitaxial layer. Analytical formulas of strain parameters in each epitaxial layer are derived under assumptions that the substrate thickness is finite and the in-plane lattice constant is the same for all epitaxial layers for dislocation free growth. As an example, the model is applied to a 405nm InGaN/InGaN multiple quantum well laser diode. Analysis result shows that AlxGa1-xN layer with Al mole fraction of 0.06 and the thickness of 6${\mu}m$ is one of good templates for a laser. In fact, this layer structure coincides with experimentally optimized one.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2009.03a
• /
• pp.118-119
• /
• 2009

As the rapid development of the electronics, the demand for portable electronics and wireless sensors is growing faster, also with the increased needs of one material which can power it automatically, and then power the electrical devices. The piezoelectric effect of the PVDF material can be used for this. So in this paper, PVDF multilayer films were made for this aim. Make the PVDF / DMAc solution in the 10% concentration; use the spin coater technique to make films with the optimum process parameters: the spin rate is 1260rpm; the spin time is 70s; the dry temperature is 100$^{\circ}C$; the dry time is 30mins. And also, for obtaining the higher $\beta$-phase crystallinity, put the Ca(NH3)2.4H2O into the PVDF / DMAc solution system.

• Journal of Sensor Science and Technology
• /
• v.15 no.1
• /
• pp.47-52
• /
• 2006

This paper describes the design, fabrication and characteristics of a buckling microvalve using a MCA (multilayer ceramic actuator). The mechanical and fluidic analysis are done by finite element method. The designed structure is normally closed microvalve using buckling effect, which is consist of three separate structures; a valve seat die, an actuator die and a small piezoelectric actuator. The flow rate of the fabricated MCA valve was 0-8.13 ml/min at the applied pressure of 0-50 kPa. Maximum non-linearity was 2.24 % FS at a duty cycle of 50 %. The maximum pressure was 230 kPa and the leak rate was $3.03{\times}10^{-8}\;Pa{\cdot}m^{3}/cm^{2}$ at a supply voltage of 100 V.

• Applied Chemistry for Engineering
• /
• v.7 no.6
• /
• pp.1142-1146
• /
• 1996

Cholesterol-containing surfactant was synthesized, and it was sonicated with monomer in water to form a vesicle solution. This vesicle solution was dried to construct a membrane which had a molecular multilayer structure. Using UV irradiation the monomer in this membrane were polymerized, and then surfactant was extracted by organic solvent. Using a X-ray diffractometer, the thickness of one layer and the regularity of the multilayer were measured. And scanning electron microscopy was conducted for fractured polymer film.

• Korean Journal of Materials Research
• /
• v.17 no.2
• /
• pp.86-90
• /
• 2007

The organic-capped Ba-Ti-O nanolayers were coated uniformly on spherical Ni particles for multilayer ceramic capacitor (MLCC) applications via the formation of Ti-hydroxide nano-coating layers and their subsequent reaction with Ba-stearate at $180^{\circ}C$. The capping of organic shell on oxide coating layer changed the hydrophilic surface structure into hydrophobic one, which significantly improved the dispersion behavior in hydrophobic solvents such as terpineol and butanol. In addition, the uniform coating of Ba-Ti-O layer was advantageous to prevent Ni oxidation. This method provides a useful chemical route to fabricate organic-soluble Ba-Ti-O coated Ni particles for a highly integrated passive component.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.4
• /
• pp.20-29
• /
• 1998

In this paper, we find the values of near-end crosstalk coefficients in dual-offset stripline of a FR-4 multilayer PCB by an analytic method and a HSPICE simulation method, define calculation errors inananlytic method and the application range, simulate near-end crosstalk coefficients of the FCT(Fast CMOS TTL) in complicated dual-offset stripline by HSPICE and analyze near-end crosstalk and far-end crosstalk coefficients in dual-offset stripline. So, we analyze coupling structure of the near-end crosstalk and far-end crosstalk in the complicated dual-offset striplines that are 1[pF] capacitors termainated, and define a coupling formula of near-end crosstalk and far-end crosstalk coefficients dual-offset striplines.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.4
• /
• pp.553-563
• /
• 1994

This paper presents a filtering method using neural networks to extract fundamental frequency components of the transient wave signals in power systems. Based on the ability of multilayer feedforward neural networks to approximate any continuous function, a neural networks mapping filter is proposed for the protective distance relaying systems to extract the effective components efficiently. A characteristic feature of this mapping filter is composed of the multilayer perceptron neural networks which are trained by using random signals and those are mapped to the DFT filtering computational structure by GDR(Generalized Delta Rule). The advantage of this approach is demonstrated by the random waves and the fault transient wave signals of EMTP(electromagnetic transients program) in power systems fault conditions. The proposed method is compared with the conventional method and the simulation results show the efficiency of the neural networks.