• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.913-916
• /
• 2005

This paper describes the design, fabrication and characteristics of a piezoelectric valve using MCA(Multilayer ceramic actuator). The MCA valve, which has the buckling effect, consists of three separate structures; MCA, a valve actuator die and an a seat die. The design of the actuator die was done by FEM modeling and displacement measurement, respectively. The valve seat die with 6 trenches was made, and the actuator die, which is driven to MCA under optimized conditions, was also fabricated. After Si-wafer direct bonding between the seat die and the actuator die, MCA was also anodic bonded to the seat/actuator die structure. PDMS sealing pad was fabricated to minimize a leak-rate. It was also bonded to seat die and SUS package. The MCA valve shows a flow rate of 9.13 sccm at a supplied voltage of 100 V with a 50 % duty cycle, maximum non-linearity was 2.24 % FS and leak rate was $3.03{\times}10^{-8}pa$. $m^3/cm^2$.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제10권1호
• /
• pp.1-17
• /
• 2016

The separated management and operation of commercial IP/optical multilayer networks makes network operators look for a unified control plane (UCP) to reduce their capital and operational expenditure. Software-defined networking (SDN) provides a central control plane with a programmable mechanism, regarded as a promising UCP for future optical networks. The general control and scheduling mechanism in SDN-based optical burst switching (OBS) networks is insufficient so the controller has to process a large number of messages per second, resulting in low network resource utilization. In view of this, this paper presents the burst-flow scheduling mechanism (BFSM) with a proposed scheduling algorithm considering channel usage. The simulation results show that, compared with the general control and scheduling mechanism, BFSM provides higher resource utilization and controller performance for the SDN-based OBS network in terms of burst loss rate, the number of messages to which the controller responds, and the average latency of the controller to process a message.

• 한국자기학회지
• /
• 제10권5호
• /
• pp.210-219
• /
• 2000

질화철(FeN)막을 이용한 FeN/Co/Cu/Co와 FeN/Co/Cu/Co/Cu/Co/FeN 다층막의 자기저항효과를 조사하였다. 질소유량이 0.4 sccm 이상인 조건에서 제작한 FeN막의 결정구조는 $\alpha$-Fe와 $\varepsilon$-Fe$_3$N상의 혼합상이며 침상구조인 $\varepsilon$-Fe$_3$N상에 의해 유도되는 형상자기이방성 때문에 자기저항효과가 관찰된다. 자기저항효과는 FeN막의 질소 유량과 두께에 따라서 달라지며 이는 FeN막의 $\varepsilon$-Fe$_3$N상에 의해 유도되는 형상자기이방성이 자유층과 고착층에 미치는 범위가 질소유량과 두께에 따라 달라지기 때문이다. 자유층인 Co막의 두께가 70 $\AA$인 조건에서 가장 우수한 자기저항비와 자기저항감도를 나타내며 자기저항비는 질소유량이 0.5 sccm이고 두께가 250 $\AA$인 조건에서 제작된 FeN/Co/Cu/Co/Cu/Co/FeN 다층막에서 3.2 %로 최대값을 나타낸다. 이 다층막의 3개의 자성층은 각기 다른 보자력을 갖고 있으므로 자기저항곡선상에 각각의 보자력 차이에 의한 step을 형성하며 MRAM 등으로 응용시 4개의 신호를 동시에 구현할 수 있을 것으로 기대된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.129-132
• /
• 2004

This paper describes the design, fabrication and characteristics of a piezoelectric valve using MCA(Multilayer ceramic actuator). The MCA valve, which has the buckling effect, consists of three separate structures; MCA, a valve actuator die and an a seat die. The design of the actuator die was done by FEM modeling and displacement measurement, respectively. The valve seat die with 6 trenches was made, and the actuator die, which is driven to MCA under optimized conditions, was also fabricated. After Si-wafer direct bonding between the seat die and the actuator die, MCA was also anodic bonded to the seat/actuator die structure. PDMS sealing pad was fabricated to minimize a leak-rate. It was also bonded to seat die and SUS package. The MCA valve shows a flow rate of 9.13 sccm at a supplied voltage of 100 V with a 50 % duty cycle, maximum non-linearity was 2.24 % FS and leak rate was $3.03{\times}10^{-8}\;pa{\cdot}m^3/cm^2$. Therefore, the fabricated MCA valve is suitable for a variety of flow control equipment, a medical bio-system, automobile and air transportation industry.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제6권9호
• /
• pp.2170-2190
• /
• 2012

There are nowadays strong demands for intelligent surveillance systems, which can infer or understand more complex behavior. The application of crowd density estimation methods could lead to a better understanding of crowd behavior, improved design of the built environment, and increased pedestrian safety. In this paper, we propose a new crowd density estimation method, which aims at estimating not only a moving crowd, but also a stationary crowd, using images captured from surveillance cameras situated in various public locations. The crowd density of the moving people is measured, based on the moving area during a specified time period. The moving area is defined as the area where the magnitude of the accumulated optical flow exceeds a predefined threshold. In contrast, the stationary crowd density is estimated from the coarseness of textures, under the assumption that each person can be regarded as a textural unit. A multilayer neural network is designed, to classify crowd density levels into 5 classes. Finally, the proposed method is experimented with PETS 2009 and the platform of Gangnam subway station image sequences.

• 센서학회지
• /
• 제13권3호
• /
• pp.230-235
• /
• 2004

This paper describes the design, fabrication and characteristics of a piezoelectric valve using MCA(Multilayer ceramic actuator). The MCA valve, which has the buckling effect, consists of three separate structures; MCA, a valve actuator die and an a seat die. The design of the actuator die was done by FEM modeling and displacement measurement, respectively. The valve seat die with 6 trenches was made, and the actuator die, which is driven to MCA under optimized conditions, was also fabricated. After Si-wafer direct bonding between the seat die and the actuator die, MCA was also anodic bonded to the seat/actuator die structure. PDMS sealing pad was fabricated to minimize a leak-rate. It was also bonded to seat die and SUS package. The MCA valve shows a flow rate of 9.13 seem at a supplied voltage of 100 V with a 50% duty cycle, maximum non-linearity was 2.24% FS and leak rate was $3.03{\times}10^{-8}pa{\codt}m^{3}/cm^{2}$. Therefore, the fabricated MCA valve is suitable for a variety of flow control equipment, a medical bio-system, automobile and air transportation industry.

• 반도체디스플레이기술학회지
• /
• 제22권4호
• /
• pp.26-31
• /
• 2023

We investigated the impact of NF₃ / H₂O remote plasma dry cleaning conditions on the SiO₂ etching rate at different preparation states during the fabrication of ultra-large-scale integration (ULSI) devices. This included consideration of factors like Si crystal orientation prior to oxidation and three-dimensional structures. The dry cleaning process were carried out varying the parameters of pressure, NF₃ flow rate, and H₂O flow rate. We found that the pressure had an effective role in controlling anisotropic etching when a thin SiO₂ layer was situated between Si₃N₄ and Si layers in a multilayer trench structure. Based on these observations, we would like to provide further guidelines for implementing the dry cleaning process in the fabrication of semiconductor devices having 3D structures.

• Composites Research
• /
• 제32권6호
• /
• pp.314-318
• /
• 2019

본 연구에서는 습식 코팅 방식 중 하나인 다층박막적층법의 자동화 시스템을 제작하였다. 특히, 본 연구에서 제안한 자동화 시스템은 다층박막적층법의 공정 변수(예를 들어, 증착 재료, 코팅 깊이, 코팅 및 헹굼 시간)를 제어함으로써 손으로 작업하는 것과 동일한 변수 조작이 가능하게 설계되었다. 자동화 시스템을 통해 기판을 완벽하게 용액 안으로 침액시킬 수 있으며, 이를 통해 특별한 분자간 결합(예를 들어, 정전기적 인력, 공유 및 수소 결합)을 통해 기판 위에 균일한 다층의 박막 형성이 가능하다. 두 종류 이상의 용액으로 기판이 침액될 때, 이 기판은 다른 용액으로 이동되기 전에 청소 구역에서 헹굼과 건조 과정을 거친다. 이러한 담금, 헹굼, 건조 과정은 모두 컴퓨터 프로그램에 의해 제어 가능하다. 본 연구에서는 자동화 시스템을 통해 그래핀을 기반으로 하는 다층박막 샘플을 제작하였고, 균일한 그래핀의 적층 여부를 분석하기 위해 제작된 샘플의 흡광도와 두께를 측정하였다. 기판 위에 그래핀과 고분자 층의 적층이 진행될수록 흡광도와 두께가 균일하게 증가하는 결과를 통해, 본 연구에서 제작한 자동화 시스템이 수작업을 통한 다층박막의 적층을 완벽하게 대체 가능함을 알 수 있었다.

• 한국진공학회지
• /
• 제17권2호
• /
• pp.113-116
• /
• 2008

반도체 소자 집적도의 비약적인 발전으로 인하여 반도체 공정은 더욱 다층화 되어가고 있다. 이러한 다층화 공정에서는 필수적으로 여러 단계의 패턴을 형성하기 위하여 Photoresist(PR)를 이용한 식각 공정을 사용하게 된다. 이러한 식각 공정에서 다단계 식각 공정으로 인한 공정시간 증가와 식각 후 남은 잔여 PR residue는 초고집적화된 현 반도체 산업에서는 소자에 치명적인 문제를 발생시킨다. 따라서 본 연구에서는 기존 PR strip 용액을 플라즈마에 의하여 액체 상태로 활성화하여 기존의 건식세정법과 습식세정법을 동시에 사용하여 PR을 효과적으로 제거하기 위한 방법을 연구하였다. 플라즈마에 의하여 약액을 활성화하기 위하여 먼저 플라즈마 약액활성화를 위한 장치를 simulation하여 실험 장치에서 균일한 gas흐름을 확인하였다. 이후 플라즈마의 세기를 0V에서 100V까지 증가시켜 약액을 활성화한 후 PR을 strip하여 각 플라즈마 세기에서의 식각률을 조사하였으며 80V에서 가장 빠른 식각률을 나타났다. 또한 0V와 80V의 Dilution에 대한 영향을 확인하였으며 약액을 Dilution 후에도 식각률은 더욱 향상됨을 확인할 수 있었다. 이러한 세정 시간의 단축은 여러 단계의 식각 공정 시간을 단축하여 반도체 공정에서 소자 생산을 위한 시간을 단축하게 된다. 또한 각 세정공정마다 증가한 세정 공정으로 인하여 세정액의 사용이 많아져 세정액 폐수로 인한 환경문제가 심각해지고 있다. 세정 약액 활성화 방법을 사용함으로써 세정액의 절감효과가 나타난다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제2권1호
• /
• pp.14-23
• /
• 2010

A numerical model was developed for simulating a three-dimensional multilayer hydrodynamic and thermodynamic model in domains with irregular bottom topography. The model was designed for examining the interactions between flow and topography. The model was based on the three-dimensional Navier-Stokes equations and was solved using the fractional step method, which combines the finite difference method in the horizontal plane and the finite element method in the vertical plane. The numerical techniques were described and the model test and application were presented. For the model application to the northern part of Ariake Sea, the hydrodynamic and thermodynamic results were predicted. The numerically predicted amplitudes and phase angles were well consistent with the field observations.