• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.385-386
• /
• 2007

We prepared the Al doped ZnO coating Ag multilayer thin films on glass without substrate heating using FTS system. The structure of multilayer thin films has Al doped ZnO/Ag/Al doped ZnO(AZO/Ag/AZO). The thickness of top and bottom AZO thin films were fixed to 50 nm, respectively and controlled the thickness of Ag thin films with deposition time. As-doped multilayer thin films were prepared at 1mTorr and input power (DC) of 100W at room temperature. To investigate the film properties, we employed four-point probe, UVNIS spectrometer, X-ray diffractometer (XRD), scanning electron microscopy (SEM), Hall Effect measurement system and Atomic Force Microscope (AFM).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.510-514
• /
• 2013

In order to prevent heat loss that occurs through the glass, low-emissivity (Low-E) coating methods with good insulating properties and high transmittance were used. InGaZnO/Ag/InGaZnO (IGZO/Ag/IGZO) multilayer thin films have been deposited on XG glass substrate by RF magnetron sputtering. Depending on the different thickness of Ag in multilayer films, the structural and optical properties of Low-E multilayer films were analyzed. By XRD analysis results, the multilayer thin films were observed to be amorphous structure regardless of Ag thickness. According to the AFM results, surface morphology of the multilayer films was observed and compared. Using UV-VIS spectroscopy, low emissivity property has been observed clearly with the transmittance of higher than 85% at visible range and lower than 30% at IR range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.12
• /
• pp.1044-1048
• /
• 2007

With development of electronic products the demands for miniaturization and weight-lightening have increased until a recent date. Accordingly, The effort to substitute glass substrates was widely made. However, polymer substrates have weak point that substrates were damaged at high temperature. In this paper, we deposited transparent conductive film at low temperature. And we inserted Au thin film between oxide to compensate for deteriorated electrical characteristics. Ga-doped ZnO(GZO) multilayer coatings were deposited on glass substrate by DC sputtering. The optimization of deposition conditions of both AZO and Au layers were performed to obtain better electrical and optical characteristics in advance. We presumed that the properties of multilayer were affected by the deposition process of both GZO and Au layers. The best multilayer coating exhibited the resistivity of $2.72{\times}10^{-3}\;{\Omega}-cm$ and transmittance of 77 %. From these results, we can confirm a possibility of the application as transparent conductive electrodes.

• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.187-193
• /
• 2010

Chromium nitride (CrN) samples with two different layer structures (multilayer and single layer) were coated on bipolar plates of polymer electrolyte membrane fuel cells (PEMFC) using the reactive sputtering method. The effects with respect to layer structure on corrosion resistance and overall cell performance were investigated. A continuous and thin chromium nitride layer ($Cr_{0.48}\;N_{0.52}$) was formed on the surface of the SUS 316L when the nitrogen flow rate was 10 sccm. The electrochemical stability of the coated layers was examined using the potentiodynamic and potentiostatic methods in the simulated corrosive circumstances of the PEMFC under $80^{\circ}C$. Interfacial contact resistance (ICR) between the CrN coated sample and the gas diffusion layer was measured by using Wang's method. A single cell performance test was also conducted. The test results showed that CrN coated SUS316L with multilayer structure had excellent corrosion resistance compared to single layer structures and single cell performance results with $25\;cm^2$ in effective area also showed the same tendency. The difference of the electrochemical properties between the single and multilayer samples was attributed to the Cr interlayer layer, which improved the corrosion resistance. Because the coating layer was damaged by pinholes, the Cr layer prevented the penetration of corrosive media into the substrate. Therefore, the CrN with a multilayer structure is an effective coating method to increase the corrosion resistance and to decrease the ICR for metallic bipolar plates in PEMFC.

• Polymer(Korea)
• /
• v.35 no.2
• /
• pp.130-135
• /
• 2011

Along with the fast development of electronics, the demands of portable electronics and wireless sensors are growing rapidly. The need for self-powering materials capable of powering the electrical devices attached to them is increasing, The piezoelectric effect of polyvinylidene fluoride (PVDF) can be used for this purpose. PVDF has a special crystal structure consisting of a ${\beta}$-phase that can produce piezoelectricity. In this paper, multilayer PVDF films were fabricated to increase the ${\beta}$-phase content. A solution of 10% concentration N;N-dimethylacetamide (DMAc) in PVDF (PVDF/DMAc) was used to fabricate the films via spin coating technique with the following optimum process parameters: a spin rate of 850 rpm, spin time of 60 s, drying temperature of $60^{\circ}C$, and drying time of 30 min, Compared with single-layer PVDF films, the multilayer films exhibited higher ${\beta}$-phase content. The ${\beta}$-phase content of the films increased gradually with increasing number of layers until 4, Maximum ratio of ${\beta}$-phase content was 7.72.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1253-1258
• /
• 2014

The tribological properties of TiC, TiN and TiC/TiN coatings on steels prepared by the cathodic-arc (CA) ion plating technique were investigated. Experiments were carried out on a tribo-test machine using a Falex journal V block system. The friction and wear characteristics of the coatings were determined by varying the applied load and sliding speed. The TiC, TiN and TiC/TiN coatings markedly increased the tribological characteristics of the surface. As far as a single layer coating was concerned, TiN goes better results than TiC. However, the TiC/TiN multilayer coating performed better than either single layer coating. The major factor in the improved performance of the multilayer coating was the role of TiC in improving the adhesion between the external TiN layer and the substrate steel.

• Journal of Powder Materials
• /
• v.29 no.3
• /
• pp.226-232
• /
• 2022

In this study, a new manufacturing process for a multilayer-clad electrical contact material is suggested. A thin and dense BCuP-5 (Cu-15Ag-5P filler metal) coating layer is fabricated on a Ag plate using a high-velocity oxygen-fuel (HVOF) process. Subsequently, the microstructure and bonding properties of the HVOF BCuP-5 coating layer are evaluated. The thickness of the HVOF BCuP-5 coating layer is determined as 34.8 ㎛, and the surface fluctuation is measured as approximately 3.2 ㎛. The microstructure of the coating layer is composed of Cu, Ag, and Cu-Ag-Cu3P ternary eutectic phases, similar to the initial BCuP-5 powder feedstock. The average hardness of the coating layer is 154.6 HV, which is confirmed to be higher than that of the conventional BCuP-5 alloy. The pull-off strength of the Ag/BCup-5 layer is determined as 21.6 MPa. Thus, the possibility of manufacturing a multilayer-clad electrical contact material using the HVOF process is also discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.11-17
• /
• 2001

Industrial use of physical vapor deposition(PVD) has been widely expanded during last two decades, and in the mean time plasma assistance in PVD has become an essential tool in preparing compound films with dense microstructure. The principles of electron beam-based plating, balanced and unbalanced magnetron sputtering and cathodic arc deposition. consisting three basic configuration of plasma assisted PVD(PAPVD)process, were reviewed. Recent technical development in PVD coating process were discussed. This paper tries to show tendency for developing new coating film on cutting tools.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.11
• /
• pp.895-899
• /
• 2011

Multiferroic BFO/PZT(5/95) multilayer films were fabricated by spin-coating method on the Pt/Ti/$SiO_2$/Si substrate alternately using BFO and PZT(9/95) alkoxide solutions. The structural and dielectric properties were investigated with variation of the solvent and the number of coatings. All films showed the typical XRD patterns of the perovskite polycrystalline structure without presence of the second phase such as $Bi_2Fe_4O_3$. BFO/PZT multilayer thin films showed the typical dielectric relaxation properties with increase an applied frequency. The average thickness of 6-coated BFO/PZT multilayer film was about 600 nm. The dielectric properties such as dielectric constant, dielectric loss and remnant polarization were superior to those of single composition BFO film, and those values for BFO/PZT multilayer film were 1199, 0.23% and 12 ${\mu}C/cm^2$.

• Journal of Ceramic Processing Research
• /
• v.23 no.5
• /
• pp.583-588
• /
• 2022

KTN/BFO multilayer films were manufactured using the spin-coating method on Pt/Ti/SiO2/Si substrate with KTN(62/38) andBFO metal alkoxide solutions. The mean thickness of the multilayer films was about 420-450 nm. A rough interfacial layerwas observed at the interface between the lower substrate and the film when sintered at 650oC. Dense microstructures withoutpores inside of the films were shown via TEM analysis, and an interface between the KTN and BFO layers was clearlyobserved. The Curie temperature was about 16oC. Dielectric constant and dielectric loss were 1380 and 0.384 at 20oC,respectively. Coercive field of the 2-layer and 6-layer films were 72.6 and 80.4 kV/cm at room temperature, respectively. ΔTand EC coefficient of the 6-layer films sintered at 630oC were 1.96oC and 0.13×10-6 oCmV-1, respectively.