• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1595-1597
• /
• 2003

This paper presents the deposition of ${\mu}c$-Si:H thin-film and fabrication of a solar cell by VHF-PECVD method. The ${\mu}c$-Si:H thin films and pin-type solar cells are fabricated using multi-chamber cluster tool system. A 7.4% conversion efficiency was achieved from ${\mu}c$-Si:H thin film solar cells with total thickness less than $5{\mu}m$. The physical characteristic was measured by Raman spectroscopy, Solar cell characteristic was measured under AM1.5 illumination.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.171-174
• /
• 1994

The drive towards ultra-large-scale integrated circuits a continuous intermetal dielectric films for multi layer interconection. Optimum condition of remote plasma enhanced chemical vapour deposition(RPECVD) was achieved by orthogonal array method. Chracteristics of SiO$_2$ films deposited by using remote PECVD with N$_2$O gas were investigated. Etching rate of SiO$_2$ films in P-echant was about 6[A/s] that was the same as the thermal oxide. The films a showed high breakdown voltage of 7(MV/cm) and a resistivity of Bx10$\^$13/[$\Omega$cm] at 7(MV/cm). The interface Trap density of SiO$_2$ has been shown excel lent properties of 5x10$\^$10/[/$\textrm{cm}^2$eV]. It was observed that the dielectric constant dropped to a value of 4. 29 for 150 [W] RF power.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.430-430
• /
• 2008

Using multi plasma enhanced chemical vapor deposition system (Multi-PECVD), p-a-Si:H deposition layer as a $p^+$ region which was annealed by laser (Q-switched fiber laser, $\lambda$ = 1064 nm) on an n-type single crystalline Si (100) plane circle wafer was prepared as new doping method for single crystalline interdigitated back contact (IBC) solar cells. As lots of earlier studies implemented, most cases dealt with the excimer (excited dimer) laserannealing or crystallization of boron with the ultraviolet wavelength range and $10^{-9}$ sec pulse duration. In this study, the Q-switched fiber laser which has higher power, longer wavelength of infrared range ($\lambda$ = 1064 nm) and longer pulse duration of $10^{-8}$ sec than excimer laser was introduced for uniformly deposited p-a-Si:H layer to be annealed and to make sheet resistance expectable as an important process for IBC solar cell $p^+$ layer on a polished n-type Si circle wafer. A $525{\mu}m$ thick n-type Si semiconductor circle wafer of (100) plane which was dipped in a buffered hydrofluoric acid solution for 30 seconds was mounted on the Multi-PECVD system for p-a-Si:H deposition layer with the ratio of $SiH_4:H_2:B_2H_6$ = 30:120:30, at $200^{\circ}C$, 50 W power, 0.2 Torr pressure for 20 minutes. 15 mm $\times$ 15 mm size laser cut samples were annealed by fiber laser with different sets of power levels and frequencies. By comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 50 mm/s of mark speed, 160 kHz of period, 21 % of power level with continuous wave mode of scanner lens showed the features of small difference of lifetime and lowering sheet resistance than before the fiber laser treatment with not much surface damages. Diode level device was made to confirm these experimental results by measuring C-V, I-V characteristics. Uniform and expectable boron doped layer can play an important role to predict the efficiency during the fabricating process of IBC solar cells.

• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.331-340
• /
• 2010

3D fluid based numerical modelling is done for a VHF multi hollow cathode array plasma enhanced chemical vapor deposition system. In order to understand the fundamental characteristics of it, Ar plasma is analyzed with a condition of 40 MHz, 100 Vrf and 1 Torr. For hole array of 6 mm diameter and 20 mm inter-hole distance, plasma is well confined within the hole at an electrode gap of 10 mm. The peak plasma density was $5{\times}10^{11}#/cm^3$ at the center of the hole. When the substrate was assumed at ground potential, electron temperature showed a peak at the vicinity of the grounded walls including the substrate and chamber walls. The reaction rate of metastable based two step ionization was 10 times higher than the direct electron impact ionization at this condition. For $H_2$, the spatial localization of discharge is harder to get than Ar due to various pathways of electron impact reactions other than ionization.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.9
• /
• pp.423-430
• /
• 2002

The fabrication and experimentation of multi-channel electrodes which enable detecting and recording of multi-site neuronal signals have been investigated. A multi-channel electrode array was fabricated by depositing 2000${\AA}$ thick Au layer on the 1000${\AA}$ thick Ti adhesion layer on a glass wafer. The metal paths were patterned by wet etching and passivated by depositing a PECVD silicon nitride insulation layer to prevent signals from intermixing or cross-talking. After placing a thin slice of rat cerebellar granule cell in the culture ring located in central portion of the multi-channel electrode plate, a neuronal signal from an electrode which is in contact with the cerebellar granule cell has been detected. It was found that the electrode impedance ranges 200㏀∼1㏁ and the impedance is not changed by cleaning with nitric acid. Also, the impedance is inversely proportion to the exposed electrode area and the cross-talk is negligible when the electrode spacing is bigger than 600$\mu\textrm{m}$. The amplitude and frequency of the measured action potential were 38㎷ and 2㎑, which are typical values. From the experimental results, the fabricated multi-channel electrode array proved to be suitable for multi-site neuronal signal detection for the analysis of a complicated cell network.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.600-605
• /
• 2010

In order to meet the requirements of faster speed and higher packing density for devices in the field of semiconductor manufacturing, the development of Cu/Low k device material is explored for use in multi-layer interconnection. SiOC(-H) thin films containing alkylgroup are considered the most promising among all the other low k candidate materials for Cu interconnection, which materials are intended to replace conventional Al wiring. Their promising character is due to their thermal and mechanical properties, which are superior to those of organic materials such as porous $SiO_2$, SiOF, polyimides, and poly (arylene ether). SiOC(-H) thin films containing alkylgroup are generally prepared by PECVD method using trimethoxysilane as precursor. Nano voids in the film originating from the sterichindrance of alkylgroup lower the dielectric constant of the film. In this study, methyltriphenylsilane containing bulky substitute was prepared and characterized by using NMR, single-crystal X-ray, GC-MS, GPC, FT-IR and TGA analyses. Solid-state NMR is utilized to investigate the insoluble samples and the chemical shift of $^{29}Si$. X-ray single crystal results confirm that methyltriphenylsilane is composed of one Si molecule, three phenyl rings and one methyl molecule. When methyltriphenylsilane decomposes, it produces radicals such as phenyl, diphenyl, phenylsilane, diphenylsilane, triphenylsilane, etc. From the analytical data, methyltriphenylsilane was found to be very efficient as a CVD or PECVD precursor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.409-409
• /
• 2010

솔라셀은 차세대 대체 에너지 소스로 최근 큰 각광을 받고 있다. 솔라셀의 제조에 있어 가장 중요한 공정은 마이크로 결정질 및 비결정질 실리콘(uC-Si:H and a-Si:H) 박막을 증착하는 PECVD (Plasma Enhanced CVD)공정이다. 현재까지 이 증착공정을 위한 플라즈마 소스로 CCP(Capacitively Coupled Plasma)가 주로 사용되어 왔다. 그러나, CCP를 플라즈마 소스를 사용한 경우 솔라셀 대량 생산 적용시 다른 방법들에 비해 긴 공정 시간이 해결해야 할 문제점으로 대두되었다. 본 발표에서는 솔라셀의 대량 생산을 위한 마이크로 결정질 실리콘 박막 증착에 있어 현 시점에서 해결되어야 할 문제점에 대해 고찰해 보고자 한다. 현재까지 이러한 문제점들을 해결하기 위해 적용되어 왔던 플라즈마 소스들을 나열하고 이러한 플라즈마 소스에 대한 특성 및 문제점들을 고찰한다. 또한, PECVD 공정상의 문제점을 해결하기 위한 플라즈마 조건을 플라즈마 벌크에서의 전자에너지 분포를 기준으로 제시하고자 한다. 솔라셀용 결정질 실리콘 박막 증착용 플라즈마 소스로 hollow cathode 방전이 가장 유력시되고 있다. 본 연구에서는 CCP 플라즈마에서 hollow cathode 방전시 발생되는 플라즈마 특성에 대한 기초 연구를 제시한다. 기초 연구를 위해 다양한 불활성 가스인 아르콘, 헬륨, 크립톤 가스에 13.56 MHz의 RF 파워를 인가하고 방전되는 플라즈마 밀도 변화를 관찰하였다. 특히, 다양한 hole diameter에서 발생되는 플라즈마 밀도의 변화를 기존 평면 CCP 플라즈마의 밀도에 비교하여 분석함으로써 hole diameter에 따른 효과를 관찰하였다. 이러한 결과는 PIC 시뮬레이션을 통해 얻은 전자에너지 분포함수를 바탕으로 메커니즘을 논의하고자 한다. 마지막으로 솔라셀용 PECVD공정을 위해 고밀도 플라즈마 소스의 필요성뿐 만 아니라 대면적 소스의 구현에 대한 문제점을 고찰하였다. 대면적 공정에서 가장 중요한 핵심 연구 이슈는 공정 균일도를 높이는 것이다. CCP 플라즈마 소스에서 전극의 크기가 대면적화 됨에 따라 발생되는 전자기파 효과에 의한 불균일도에 대해 RF 전자기장 시뮬레이션을 통해 확인하고, 균일도 확보를 위한 방안에 대한 논의하고자 한다.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.105-111
• /
• 1999

This paper presents experimental results on the electrical properties of hydrogenated amorphous carbon films(a-C:H) prepared by PECVD. DC conductance of a-C:H was measured as a function of temperatures in the range of 100 to 423K. We studied two a-C:H films: one was well explained by the Mott's Variable Range Hopping(VRH) rule, but the other sample did not follow it. However, the conduction data of second sample were well fitted to Shimakawa's Multi-Phonon Hopping(MPH) model according to which conductivity is proportional to $T^M$ with m=15-17. but, in our samples, m was 10-12. Also a-C:H showed several bias effects like relaxation of conductance, bias-dependent conductance and the change of conductance slope in 1n(${\sigma}{\sqrt{T}}$) vs. $T^{1/4}$ plot. In this study we interpret these data by bias-dependent detrapping model.

• Journal of Korean Ophthalmic Optics Society
• /
• v.2 no.1
• /
• pp.103-110
• /
• 1997

This work presents experimental results on the electrical properties of hydrogenated amorphous carbon films(a-C : H) prepared by PECVD. Conductance of a-C: H was measured as a function of temperatures in the range of 100 to 423K. We studied two a -C: H films: one was well explanied by the Mott's variable range hopping(VRH) rule. But the other sample did not follow it. The conduction data of second sample were well fitted to Shimakawa's multi-phonon hopping(MPH) model according to which conductivity is proportional to Tm with m= 15~17. But, in our samples, m was 10~12.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.692-693
• /
• 2002

Well-aligned multi-wall carbon nanotubes (MWNTs) were fabricated by utilizing a radio frequency plasma-enhanced chemical vapor deposition (rf-PECVD) system from Ni particles at the bottom of anodic alumina nanoholes (AAN). To remove the amorphous graphite layers on the AAN surface and to eliminate the protrusion of MWNT tips, the AAN surface with MWNTs were treated by external rf plasma source. As a result, the AAN surface almost became flat without having any protrusion of MWNT tips. The diameter, length of MWNTs and AAN were investigated by using a scanning electron microscopy (SEM). Raman spectroscopy was also used to characterize wall structure of the carbon nanotube. And the emission properties of the MWNTs were measured for the application of field emission display (FED) in near future.