• 제어로봇시스템학회논문지
• /
• 제20권11호
• /
• pp.1125-1130
• /
• 2014

In this paper, we discuss the relation between the motion profile and pre-filter. As previously reported in various literatures [1-3], a tuned motion profile can effectively reduce residual vibration by placing inherent zeros of the motion profile at the vibratory pole of systems similar to the role of the input shaping technique. From the results, we factorize the motion profile into a basis function and an input shaper. In contrast to the previously reported impulse-sequence-based input shapers, the input shaper extracted from the motion profile has unique characteristics. Thanks to the characteristics of the input shaper extracted from the motion profile, it has advantages to reduce the vibrations caused by not only the modeled vibratory mode but also unmodeled dynamics which exist in higher frequency ranges.

• 한국정밀공학회지
• /
• 제29권10호
• /
• pp.1110-1118
• /
• 2012

In this study, for reducing the residual vibration in high speed motion control stage, an improved 5th order polynomial motion profile was developed. When a stage is moving, the current through the motor coils has the same profile of input motion profile of acceleration, therefore the characteristics of the acceleration input profile directly affect on the performance of the amplifier that includes the current control loop. Commonly low cost amplifier and motor has a narrow current control bandwidth, therefore the proposed algorithm was designed based on this practical constraint. Simulation and experimental results showed that the proposed algorithm clearly has low residual vibration characteristics than conventional 5th order polynomial motion profile on the same drive condition.

• 제어로봇시스템학회논문지
• /
• 제18권4호
• /
• pp.308-313
• /
• 2012

Robust tuning rules of the motion profile are proposed to minimize the residual vibration. For asymmetric S-curve profile, tuning rules are analytically formulated using Laplace-domain approach. When the system modeling is known exactly, by placing a single zero of the motion profile on the pole of the system, the residual vibration can be perfectly eliminated under undamped system. However, if there are some amounts of the modeling errors, the residual vibration significantly increases. To track this issue, the robust tuning rules against modeling error are discussed. One of the proposed robust tuning rules is placing the multiple zeros of the motion profile on the pole of the system, and the other is placing the zeros of the motion profile around the pole of the system. Thanks to the proposed robust tuning rules, motion profile becomes more robust to modeling errors while minimizing the residual vibration. By simulation, the effectiveness of the proposed robust tuning rules is verified.

• 제어로봇시스템학회논문지
• /
• 제18권12호
• /
• pp.1079-1085
• /
• 2012

For precise motion control, S-curve velocity profile is generally used but it has disadvantage of relatively long calculation time for floating-point arithmetics. In this paper, we present a new generating method for velocity profile to reduce delay time of profile generation so that it overcomes such disadvantage and enhances the efficiency of precise motion control. In this approach, the velocity profile is designed based on the gamma correction expression that is generally used in image processing to obtain a smoother movement without any critical jerk. The proposed velocity profile is designed to support both T-curve and S-curve velocity profile. It can generate precise profile by adding an offset to the velocity profile with decimals under floating point that are not counted during gamma correction arithmetic operation. As a result, the operation time is saved and the efficiency is improved. The proposed method is compared with the existing method that generates velocity profile using ring buffer on a 8-bit low-cost MCU. The result shows that the proposed method has no delay in generating driving profile with good accuracy of each cycle velocity. The significance of the proposed method lies in reduction of the operation time without degrading the motion accuracy. Generated driving signal also shows to verify effectiveness of the proposed method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.785-786
• /
• 2010

• 한국정밀공학회지
• /
• 제31권8호
• /
• pp.697-703
• /
• 2014

This paper is study of solving vibration problem occurred in moving hand of wafer transfer robot in semiconductor manufacturing line. Long settling time for decreasing vibration makes low production rate, and moreover the excessive vibration of hand sometimes breaks the wafer in a cassette. The ways of reducing the moving speed and changing the type of motion profile did not help for lessening vibration. Therefore, we analyzed the mechanical property of the hand such as natural frequency, and frequency component of the motion profile currently used in the manufacturing line. In several conditions of motion profile, we found the best condition of which the frequency component in near of natural frequency of the hand is minimal and this induced small vibration in moving hand. The results were verified theoretically and experimentally using frequency analysis.

• 제어로봇시스템학회논문지
• /
• 제12권10호
• /
• pp.1012-1017
• /
• 2006

By breaking the symmetry of the velocity profile in the S-curve, we developed a fast starting and smooth ending motion profile, named asymmetric S-curve(AS-curve). The problem for generating motion profile is formulated, and the algorithm for the AS-curve is derived and the flow chart of the AS-curve is illustrated. By various simulations, the derived algorithm is tested and shows the validity. This AS-curve can be applied to the high precision machines where fast and vibrationless motion is required in the near future.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.83-84
• /
• 2012

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.788-793
• /
• 1995

For a linkage mechanism deiven by cam, cam profile is the major design factor and is determined by the motion type od cam follower. If a cam mechanism has additional kinematic linkages besides cam and follower then the follower motion should be specified form the motion of end linkage member so that cam would be able to generate the desired end linkage motion. In this paper, a cam-linkage mechanism is constructed with the combinations of modular linkage elements including cam and follower and as a resullt, a planar cam-linkage mechanism design software with the cam profile optimization function is developed and presented.

• 한국항공우주학회지
• /
• 제34권3호
• /
• pp.6-13
• /
• 2006

본 연구에서는 저 레이놀즈수 유동에서 flapping운동을 하는 익형이 가질 수 있는 2차원 평면상의 운동궤적에 따른 공력특성을 연구하였다. 익형이 유동흐름방향으로 왕복 운동하는 lead-lag운동과 plunging운동의 조합으로 2차원 평면상에 나타날 수 있는 여러 운동궤적을 합성하여 flapping 주파수 변화에 따른 공력계수들의 변화를 살펴보았다. 상하방향의 순수 plunging운동에 lead-lag운동을 추가함으로써, 평균추력계수와 평균양력계수를 증가시킬 수 있는 운동궤적이 존재함을 확인하였다. 아울러 운동주기 동안 나타나는 추력계수와 양력계수의 변화를 비교하여 upstroke와 downstroke시 나타나는 공력특성을 파악하였다.