• 한국운동역학회지
• /
• 제20권2호
• /
• pp.117-127
• /
• 2010

The axes of upper forearm coordinate system have been considered as principal axis of each segment which was component of elbow joint. The purpose of this study was to verify whether the mean direction(principal axis) of instantaneous axes of rotation for pure flexion/extension motion coincided with the flexion/extension axis of upper forearm coordinate system. The same procedure was done for pronation/supination motion. Furthermore, it was tested indirectly that there was an interaction effect between the two rotational motions. The results showed that most segment coordinate axes statistically were not consistent with the mean directions of flexion/extension and pronation/supination axes of rotation. From the results, it would be concluded that the ISB coordinate systems was proved to be a little valid for human movement analysis. There also was an effect of pronation/supination angles on flexion/extension motion.

• Journal of Multimedia Information System
• /
• 제7권4호
• /
• pp.269-276
• /
• 2020

The small craft including jet-board for leisure are commonly smaller than the general commercial vessels. For the floating vessel, the motion analysis is significantly important component to design the shape. It is, however, hardly predicting its behavior by using conventional boundary element method due to violating small amplitude assumption for potential theory. The computational fluid dynamics method can afford to simulate such small craft, but its grid system was not able to calculate motion, because movable body disturbs the grid system by confliction. The dynamics fluid body interaction model with over-set mesh system can be dealt with movable floating body under irregular ocean wave. In this study, several cases were considered to reveal that DFBI is essential method to predict floating body motion. The single phase simulate was conducted to establish the shape perfection, and then the validated vessel was simulated with ocean waves weather DFBI option on or off. Through the comparison, the results between the cases of DFBI on and off shows significantly difference. It was claimed that the DFBI was necessary not only to calculation body motion, but also to predict accurate drag and lift force on the floating body for small size craft.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국내학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.1129-1135
• /
• 1993

For successful implementation of robotic painting system, a structured design and analysis procedure is necessary. In designing robotic system, both functional and economical feasibility should be investigated. As the robotization is complicated task involving implementation details(such as robot selection, accessory design, and spatial layout) together with operation details, a computerized method should be sought. However, any conventional robotic design system and off-line programming system cannot accomodate such a need. In this research, we develop an interactive design support system for robotization of a cycle painting line. With the developed system called SPRPL(Simulation Package for Robotic Painting Line) users can design the painting objects(via FRAME module), select robot model (ROBOT), design the part hanger (FEEDER), and arrange the workcell. After motion programming (MOTION), the design is evaluated in terms of: a) workspace analysis, b) coating thickness analysis, and c) cycle time (ANALYSIS). By iterative design and evaluation procedure, a feasible and efficient robotic design can be attained. As the developed system has motion planning and analysis features, it can be also used as an off-line robot programming system in operation stage. Including the details of each module, this paper also presents a case study made for an actual painting line.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.1147-1156
• /
• 1993

In order to analyze lateral control in the backward maneuver of a tractor -trailer combination , a kinematic vehicle model and a human operator model with time delay were utilized for the operator/vehicle system. The analysis was carried out using the frequency domain approach. The open-loop stability of the vehicle motion was analyzed through the transfer functions. The sensitivity of the stability of the vehicle motion. to a change in the steering angle, was also analyzed. A mathematical model of the closed -loop operator/vehicle system was then formulated. The closed -loop stability of the operator /vehicle system was then analyzed. The effect of the delay time on the system was also analyzed through computer simulation.

• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.1994-2003
• /
• 2003

The vibration of a flexible cantilever tube with nonlinear constraints when it is subjected to flow internally with fluids is examined by experimental and theoretical analysis. These kinds of studies have been performed to find the existence of chaotic motion. In this paper, the important parameters of the system leading to such a chaotic motion such as Young's modulus and the coefficient of viscoelastic damping are discussed. The parameters are investigated by means of system identification so that comparisons are made between numerical analysis using the design parameters and the experimental results. The chaotic region led by several period-doubling bifurcations beyond the Hopf bifurcation is also re-established with phase portraits, bifurcation diagram and Lyapunov exponent so that one can define optimal parameters for system design.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.160-167
• /
• 2004

A two degree-of-freedom mathematical model is presented to investigate the friction mechanism of a disc brake system. A contact parameter is introduced to describe the coupling between the in-plane and the out-of-plane motions. The model with the contact parameter is considered under the assumption that the out-of-plane motion depends on the friction force along the in-plane motion. In order to describe the relationship between the friction force and the out-of plane motion, the dynamic friction coefficient is considered as a function of both relative velocity and normal farce. Using this friction law, a contact stiffness matrix along the normal direction can be obtained. The out-of-plane motion is then investigated by both the stability analysis and the numerical analysis for various parametric conditions. The results show that the stiffness parameters of the pad and the disc must be controlled at the same time. Also, the numerical analysis shows the existence of limit cycle caused by the effect of intermittent contact stiffness.

• 제어로봇시스템학회논문지
• /
• 제21권11호
• /
• pp.1064-1069
• /
• 2015

Control Moment Gyro (CMG) has been used as an indirect actuator of a single-wheel robot system GYROBO, developed at Chungnam National University. The flip motion of the gimbal system produces the gyroscopic motion onto the body system while the body motion also produces the gyroscopic motion onto the gimbal system inversely. In this paper, the intuitive equation of the inverse gyroscopic effect is derived as the direct relation between the rate of the body system and the rate of the gimbal system. Experiments on the inverse gyroscopic effect under the chaotically generated disturbance are conducted. Experimental data are approximated by a linear equation using the least square method.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2003년도 추계학술발표논문집
• /
• pp.209-216
• /
• 2003

There are two kinds of controllers in a continuous process system. One is for tension control of a moving web and the other for lateral motion control. The inter-connection between tension and lateral behaivior of web has not yet been considered in the analysis of web dynamics and designing of control stragagies. But the effect of tension variation on the lateral motion of a moving web is observed in the most manufacturing systems. In this paper, experimental studies was carried out to find out the inter-correlation between tension and lateral motion of a web using a 3-span web transport system which consists of two displacement type guiders. As a result, it was found that there are typical operating conditions that tension and lateral motion are correlated each other.

• 대한인간공학회지
• /
• 제33권3호
• /
• pp.175-189
• /
• 2014

Objective: The goal of this research is to develop new user behavior model using user motion analysis with microscopic perspective for attracting user's participation in interactive space. Background: The interactive space is 'human's place', which is made up of complex elements of digital virtual space and traditional analog and physical environment based on human-computer interaction system. Human behavior has changed in it at the same time. If the user couldn't make participation in interaction, the purpose of the system is not met, which reduces its effect. Therefore, we need to focus on interactive space that is potential future direction from a new point of view. Method: For this research, we would discuss and study fields of interactive space; (1) finding definition of interactive space and studying background of theory about it. (2) providing base of user behavior model with study of user's context that is to be user information and motion. (3) examining user motion, classify basic motion type and making user participation behavior model in phases. Results: Through this process, user's basic twenty motions which are systematized are taken as a standard for analysis of interaction process and participation in interactive space. Then, 'NK-$I^5$ (I Five)' model is developed for user participation types in interactive space. There are five phases of user participation behavior: Imperception, Interest, Involvement, Immersion, and Influence. In this analysis, three indicators which are time, motion types, and user relationship are found to be related to participation. Conclusion: The capabilities and limitation of this research is discussed to attract user participation. This paper focuses especially on contribution of design to lead user's participation in interactive system and expectation to help adapt to user centered design of various interactive space with new aspect of user behavior research. Application: The results of the 'NK-$I^5$ (I Five)' model might help to realize successful interactive space based on user centered design.

• International Journal of Aeronautical and Space Sciences
• /
• 제2권1호
• /
• pp.28-43
• /
• 2001

Developed in these two series of paper is a complex dynamic model representing the motion of aircraft on the ground and a computer program for numerical simulation. The first part of paper presents the theoretical derivation of equations of motion of the landing gear system based on the physical principle. Developed model is 'structured' in the sense that the undercarriage system is regarded as an assembly of strut, tire, and wheel, where each component is modeled by a separate module. These modules are linked with two external modules-the aircraft and the runway characteristics-to carry out dynamic analysis and numerical simulation of the aircraft motion on the ground. Three sets of coordinate system associated with strut, wheel/tire and runway are defined, and external loads to each component and response characteristics are examined. Lagrangian formulation is used to derive the undercarriage equations of motion relative to the moving aircraft, and the resultant forces and moments from the undercarriage are transformed to aircraft body axes.