• Transactions of Materials Processing
• /
• v.17 no.6
• /
• pp.443-448
• /
• 2008

Fiber reinforced injection molded parts are widely used in recent years because of their improved properties of materials such as specific stiffness, specific strength, and specific toughness. The demand for products with high precision is increasing and it is important to minimize the warpage of the products. The warpage of short-fiber reinforced product is caused by anisotropy induced by fiber orientation as well as the residual stresses induced during the molding process. In order to reduce the warpage of the part, it is important to achieve successful mold design, processing control, and part design. In the present study, the design of gating system, molding condition, and part structure were carried out and verified with numerical analysis using a commercial CAE code Moldflow. The numbers and locations of gates were iteratively determined, and the molding conditions which can decrease the warpage of the part were investigated. Finally, slight structural modification of the part was conducted to reduce the locally concentrated warpage.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.3
• /
• pp.271-277
• /
• 2006

Injection molding process is the manufacturing process that can obtain a high quality products in large quantity to a low cost. Since there are many input factors in every situation that can influence part's quality, the method is difficult to save the exact simulation data. Latest, it deals with the CAE method that supports the experiment, it is applied to the Design of Experiment for the optimum injection molding process. If there are many factors, the interaction among those factors must be considered by applying Design of Experiment which is taken from the technique of minimizing the number of experiment. Without a real test, it is taken the simulation data using $Moldflow^(R)$ software. $Moldflow^(R)$ is used for the analysis of injection molding process, it is analyzed the factors that affect a warpage using the Taguchi method and then the optimal injection molding process is obtained.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.6
• /
• pp.426-432
• /
• 2021

Injection molding is used in many industrial fields such as home appliances, vehicle parts, and electronic device parts because various resins can be molded, leading to mass production of complex shapes. Generally, the empirical prediction method is used to set the initial processing conditions of injection molding. However, this approach requires a lot of cost and its presented solution is not accurate. In this paper, injection molding was simulated through the Moldflow^TM in order to manufacture the spacer for gas insulated switch. Through the simulation, the flow of the resin with respect to the diameter of the inlet was analyzed. It was found that the process was possible at a higher resin temperature as the diameter of the inlet increased. In addition, through thermal analysis during injection of the resin, it was confirmed that a stagnation phenomenon occurred at the insert portion during injection molding, and the temperature of the resin was higher than that of the mold. As in this paper, if the spacer is manufactured by optimizing the injection hole and the temperature of the injection process based on simulation, it is expected that the spacer can be manufactured with high productivity.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.6
• /
• pp.349-357
• /
• 2019

Finite element method (FEM) is utilized in the development of products to realistically analyze and predict the mechanical behavior of materials in various fields. However, the approach based on the numerical analysis of glass fiber reinforced plastic (GFRP) composites, for which the fiber orientation and strain rate affect the mechanical properties, has proven to be challenging. The purpose of this study is to define and evaluate the mechanical properties of glass fiber reinforced plastic composites using the numerical analysis models of Digimat, a linear, nonlinear multi-scale modeling program for various composite materials such as polymers, rubber, metal, etc. In addition, the aim is to predict the behavior of realistic polymeric composites. In this regard, the tensile properties according to the fiber orientation and strain rate of polybutylene terephthalate (PBT) with short fiber weight fractions of 30wt% among various polymers were investigated using references. Information on the fiber orientation was calculated based on injection analysis using Moldflow software, and was utilized in the finite element model for tensile specimens via a mapping process. LS-Dyna, an explicit commercial finite element code, was used for coupled analysis using Digimat to study the tensile properties of composites according to the fiber orientation and strain rate of glass fibers. In addition, the drawbacks and advantages of LS-DYNA's various anisotropic material models were compared and evaluated for the analysis of glass fiber reinforced plastic composites.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.112-118
• /
• 1999

Shrinkage behavior was investigated to obtain more accurate dimensions of injected molding parts for free and restricted shrinkage conditions. various parameters for metal inserted injection process, such as thickness of resin, holding pressure and time, mo이 temperature and restriction condition of mold, were considered for the analysis of shrinkage phenomena. For numerical analysis, MOLDFLOW software was used to find the deterministic parameters of filling time, temperature, pressure and holding time. Also , experimental shrinkage effects were measured through actual injection molding process and the resin thickness was under controlled as 3 mm , 5 mm, and 7mm for the shapes of plastic gear made of Polymide(PA) and Polyxymethlene(POM). The main parameters of these injection processes were found to be holding pressure, holding time and mold temperature in the case of metal inserted molding.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.1 s.178
• /
• pp.159-165
• /
• 2006

Many rubber products are used in industrial products such as various hoses, rubber belts and oil seals etc. Especially, more then 200 rubber parts are used in the automobile, but design technology of these is largely dependent on Held experiences. These methods brought about too much time and cost in the developing procedures. However, with the help of recent rapid development of non-liner computer analysis, we can develop new sound products at low cost. Therefore in this study, optimizations of design variables such as location and number of gate in order to develop CLIP rubber product made of EPDM were performed by CAE in which Cross-WLF equations are adopted. The validity of proposed variables is evaluated by comparison with real forming results.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.381-388
• /
• 2003

The paper presents our study of development for multi-cavity preform mold system which consists of hot runner system and valve gate. For this purpose, stretching blow molding process and preform injection process were simulated by Polyflow and Moldflow. Based on various results of the preform injection process analysis, process planning was established. The sectional thickness distribution of preform was optimized. Preform injection mold system was designed by these technical analysis data. Finally, 24-cavity preform mold system was successfully developed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.355-356
• /
• 2006

This paper proposes an Molding error compensation method that improves accuracy with geometry information of injected parts using three-dimensional measuring instrument. a traditional mold design has been conducted by an experience-based trial and error, whereby generally the mold designer would decide the gate location and processing conditions. as a natural consequence, almost all creats inferior goods. It's just a process of trial and error and caught in a vicious circle. Due to this reason, this paper uses a three-dimensional measuring instrument, a commercial analysis package of injection molding(Moldflow, MPI) to analysis a state of flux. In addition to that axiomatic approach.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.8
• /
• pp.71-78
• /
• 1999

The application range of injection molded parts is expanding by the development of engineering plastics with good mechanical properties. Plastic gears are specially used as automotive parts due to an excellent performance in the characteristics of a strength vs. weight, and the study of injection molding process of plastic gear using Nylon66 is performed in this study. Filling, packing and cooling analyses were done by using the simulation software like Moldflow, and a mold was designed by following the simulation results. Pin-point gates with three points were taken to satisfy the design guides like a full-shot, and lower clamping force and uniform shrinkage. Characteristics of shrinkage of molded gear and temperature difference between cavity and core sides of a mold were shown.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.316-319
• /
• 2002

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameters and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced strongly the shrinkage of injection molded part.