• Journal of electromagnetic engineering and science
• /
• v.19 no.1
• /
• pp.42-47
• /
• 2019

This paper introduces a modified Wilkinson power divider that uses uniform transmission lines for various terminated impedances and an arbitrary power ratio. For the designed power ratio, the proposed divider changes only the electrical lengths of the transmission lines between the input and output ports, and those between the output ports and the isolation resistor. In this case, even when various termination impedances of the ports exist, the divider characteristics are satisfied. To verify the feasibility of the proposed divider, two circuits were designed to operate at a frequency of 2 GHz with 2:1 and 4:1 power splitting ratios and various terminated impedances of 40, 70, and $60{\Omega}$ for one circuit, and 50, 70, and $60{\Omega}$ for the other. The measurement and simulation results were in good agreement.

• Journal of Navigation and Port Research
• /
• v.29 no.7
• /
• pp.615-618
• /
• 2005

A new structure of the Wilkinson power divider that can suppress multiple harmonics output is presented The power divider consists of T-type or $\pi$-type capacitive loads and shunt resistors. Experimental results show that this power divider suppresses the second and the third harmonic components to less than -38dB, while maintaining the characteristics of a conventional Wilkinson power divider, featuring an equal power split, a simultaneous impedance matching at all ports and a good isolation between output ports.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.46-50
• /
• 2013

A modified design that can reject the nth harmonic components in the Wilkinson power divider is presented. After adding transmission lines of electrical lengths determined by suppression terms between two transformers of the traditional design, a solution of the modified Wilkinson divider can be found. Experimental results show the second and third harmonic suppression to be -45.3 dB and -46.4 dB, respectively, while maintaining the conventional performance at the fundamental frequency.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.273-277
• /
• 2003

This paper presents a structure of the Wilkinson power divider that can suppress the 9ea harmonic output. The power divider consists of ${\lambda}/4n$ open stubs, which are located at the $3{\lambda}/4$ branches and parallel connection of resistor which shunts the output ports. Experimental results show that this power divider suppresses from 1st to 9th harmonic components to less than -37dB, while maintaining the characteristics of a conventional Wilkinson power divider; featuring an equal power split, a simultaneous impedance matching at all ports and a good isolation between output ports. these results agree quite well with the simulation results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.6
• /
• pp.579-589
• /
• 1989

In this paper, planar power dividers/combiners for millimeter waves K-band or bands which can be printed on the substrates of hybrid or monolithic IC by surface mounting are designed and studied. Power dividers/combiners, and the conductor loss of microstrip lines in particualr the existing Wilkinson power dividers/combiners is modified ad amployes by ist equivalent circuit. Microwave CAD program SUPEROMPACT is employed for the Wilkinson power combiner which is modified and analyzed to reduce the high frequency coupling between the branches of the combiner, and the method to diminish the sensitivity of the input reflection of $2^n$-way power dividers/combiners is studied employing the commerical microwave CAD program package SUPERCOMPACT.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.1
• /
• pp.42-46
• /
• 2014

A modified network to suppress the nth harmonics in a Wilkinson power divider is presented. The solution has been found by adding transmission lines, whose electrical lengths are determined by using the suppression terms, between two transformers of the traditional design. Experimental results show the second and third harmonics levels achieved are -45.3 and -46.4 dB, respectively, while the performance of the power divider at the fundamental frequency is maintained.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.8
• /
• pp.24-32
• /
• 2000

In this paper, we have designed and fabricated a new type power divider to be efficient to a size and electrical performance by folding each quarter-wavelength 70.7 Ω section into a tightly-coupled "meander-line" and inserting a slit. In this type, because of coupling, the electrical phase of quarter -wavelength line and the performance change. For this reason, with the inductive slit and the tuning of quarter-wavelength line length, we have compensated for those. The inductance value of the inserted slit is decided by its width and depth, therefore, we could improve the electrical performance through optimization of inductance. Input and output return losses of the designed power divider were -34.2 dB, -34.3 dB respectively, and isolation was -36.7 dB at 1.75 GHz. Besides, a new design approach reduced occupied substrate area by 3:1 approximately.

• Journal of Advanced Navigation Technology
• /
• v.13 no.5
• /
• pp.720-725
• /
• 2009

This paper proposes a modified Wilkinson power divider using a zero-degree composit right/left-handed(CRLH) transmission line to obtain a isolation between ports. A zero-degree CRLH transmission line, which has a total electrical length of zero, consists of a RH(Right-Handed) transmission line of a negative phase characteristic and a LH (Left-Handed) transmission line of a positive phase characteristic. To validate a value of zero-degree CRLH transmission line, the electrical lengths of RH and LH transmission line select $-30^{\circ}$ and $+30^{\circ}$ and a 2-way Wilkinson divider designed, we are measured S21 of -3.3dB, S11 of -27.5dB and S23 of -25dB at 1GHz center frequency. These characteristics are same the conventional divider using RH transmission line.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.264-272
• /
• 2009

In this paper, a Ka-band 10 W power amplifier module is designed and fabricated using MIC(Microwave Integrated Circuit) module technology which combines multiple power MMIC(Monolithic Microwave Integrated Circuit) chips on a thin film substrate. Modified Wilkinson power dividers/combiners are used for millimeter wave modules and CBFGC-PW-Microstrip transitions are utilized for reducing connection loss and suppressing resonance in the high-gain and high-power modules. The power amplifier module consists of seven MMIC chips and operates in a pulsed mode. for the pulsed mode operation, a gate pulse control circuit supplying the control voltage pulses to MMIC chips is designed and applied. The fabricated power amplifier module shows a power gain of about 58 dB and a saturated output power of 39.6 dBm at a center frequency of the interested frequency band.

• Journal of Advanced Navigation Technology
• /
• v.27 no.6
• /
• pp.828-834
• /
• 2023

In this paper, we studied an antenna that forms a wide beam width by applying a horn-shaped reflector to a patch array antenna. To implement a wide beam width, three patches were arranged in each of the four directions on a square microstrip substrate, and a horn-shaped reflector was applied to the rear of the array antenna. Through this structure, the vertical beam pattern formed from the patch was converted to a diagonal direction, and as a result, the beam widths formed in each of the four sectors were added to create a wide beam width close to a hemisphere. The proposed antenna was studied for application to UAV(unmanned aerial vehicle), and the simulation test results confirmed that the 4.5 dBi beam width was 146.8°.