• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.4
• /
• pp.491-498
• /
• 2018

The cost evaluation for voyage route planning in an ice-covered sea is one of the major topics among ship owners. Information of the ice properties, such as ice type, concentration of ice, ice thickness, strength of ice, and speed-power relation under ice conditions are important for determining the optimal route in ice and low operational cost perspective. To determine achievable speed at any designated pack ice condition, a model test of resistance, self-propulsion, and overload test in ice and ice-free water were carried out in a KRISO ice tank and towing tank. The available net thrust for ice and an estimation of the ice resistance under any pack ice condition were also performed by I-RES. The in-house code called 'I-RES', which is an ice resistance estimation tool that applies an empirical formula, was modified for the pack ice module in this study. Careful observations of underwater videos of the ice model test made it possible to understand the physical phenomena of underneath of the hull bottom surface and determine the coverage of buoyancy. The clearing resistance of ice can be calculated by subtracting the buoyance and open water resistance form the pre-sawn ice resistance. The model test results in pack ice were compared with the calculation results to obtain a correlation factor among the pack ice resistance, ice concentration, and ship speed. The resulting correlation factors were applied to the calculation results to determine the pack ice resistance under any pack ice condition. The pack ice resistance under the arbitrary pack ice condition could be estimated because software I-RES could control all the ice properties. The available net thrust in ice, which is the over thrust that overcomes the pack ice resistance, will change the speed of a ship according to the bollard pull test results and thruster characteristics (engine & propulsion combination). The attainable speed at a certain ice concentration of pack ice was determined using the interpolation method. This paper reports a procedure to determine the attainable speed in pack ice and the sample calculation using the Araon vessel was performed to confirm the entire process. A more detailed description of the determination of the attainable speed is described. The attainable speed in 1.0 m, 90% pack ice and 540 kPa strength was 13.3 knots.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.155-164
• /
• 2015

In this paper, two rotor configurations including different amount of magnet and reluctance parts are presented. The rotors are constituted by means of a flexible hybrid motor structure. Considerable features of the hybrid structure are that the combination of the magnet and reluctance parts can be suitably modified and the mechanical angle (${\beta}$) between the parts can also be varied. Two hybrid rotor configurations have been considered in this study. First, finite element (FE) simulations were carried out and the torque behaviors of the motors were predicted. The average torque ($T_{avg}$) and maximum torque ($T_{max}$) curves were obtained from FE simulations in order to find suitable ${\beta}$. Mathematical model of the motors was formed in terms of a,b,c variables considering the amount of the magnet and reluctance parts on the rotor and simulations were performed. Rotor prototypes, motor drive and drive method were introduced. Torque profiles of the motors were obtained by static torque measurement and loaded tests were also realized. Thus, simulation results were verified by experimental study. There is a good match between predictions and measurements. The proposed motors are operated with electrical $120^{\circ}$ mode as a brushless DC motor (BLDC) and torque versus speed characteristics show a compound DC motor characteristic. The motors can be named as brushless DC compound motors.

• Journal of Applied Biological Chemistry
• /
• v.51 no.1
• /
• pp.28-35
• /
• 2008

The physico-chemical properties of kapok fibers were altered via the combination processes of chlorite-periodate oxidation, in order to assess their efficacy as a heavy metal adsorbent. The chemically-oxidized kapok fibers were found to harbor a certain amount of polysaccharides, together with lowered lignin content. This alteration in lignin characteristics was clearly confirmed via FTIR and NBO yield. Moreover, chemically oxidized kapok fibers retained their hollow tube shape, although some changes were noted. The chemically oxidized kapok fibers evidenced elevated ability to adsorb heavy metal ions with the best fit for the Langmuir adsorption isotherm model. Three cycles of adsorption-desorption were conducted with in-between regeneration steps. Our experimental results indicated that chemically oxidized kapok fibers possessed excellent adsorption characteristics, and the modified kapok fibers could be completely regenerated with almost equimolar diluted sodium hydroxide. Pb, Cu, Cd and Zn ions evidenced adsorption rates of 93.55%, 91.83%, 89.75%, and 92.85% on the chemically oxidized kapok fibers. The regeneration efficiency showed 73.58% of Pb, 71.55% of Cu, 66.87% of Cd, and 75.00% of Zn for 3rd cycle with 0.0125N NaOH.

• Korean Journal of Food Science and Technology
• /
• v.21 no.1
• /
• pp.75-79
• /
• 1989

The rheological properties of sugar and cocoa particle suspensions in cocoa butter under molten condition were analyzed with Haake rotationary viscometer. Both suspensions had yield value and showed rheopexy at low shear rate and thixotropy at high shear rate. Flow behaviors of the suspensions were analyzed with modified Casson model. Casson viscosity and yield value increased with increasing the concentration of sugar and cocoa particles. There was an obvious dependence of the Casson viscosity and yield value on the particle size distributions that was represented by the Sauter mean diameter of the particles. Casson viscosity and yield value of cocoa butter-sugar suspension increased with increasing the fineness of sugar particle crystal. With increasing the fineness of cocoa particle a decreasing Casson viscosity of cocoa butter-cocoa particle suspension was achieved, but the yield value did not change significantly with cocoa particle size. Therefore, it was predicted that the best rheological properties of chocolate could be obtained with the combination of coarse ground sugar $(d=36.30{\mu}m)$ and fine ground cocoa particle $(d=14.81{\mu}m)$ within the studied range.

• Steel and Composite Structures
• /
• v.52 no.4
• /
• pp.391-403
• /
• 2024

The flexural behavior of composite sandwich wall panels with different thicknesses, numbers of holes, and hole forms, and arrangement form of longitudinal steel bar (uniform type and concealed-beam type) are investigated. A total of twelve composite sandwich wall panels are prepared, utilizing modified polystyrene particles mixed with foam concrete for the flexural performance test. The failure pattern of the composite sandwich wall panels is influenced by the extruded polystyrene panel (XPS) panel thickness and the reinforcement ratio in combination, resulting in both flexural and shear failure modes. Increasing the XPS panel thickness causes the specimens to transition from flexural failure to shear failure. An increase in the reinforcement ratio leads to the transition from flexural failure to shear failure. The hole form on the XPS panel and the steel bar arrangement form affect the loading behavior of the specimens. Plum-arrangement hole form specimens exhibit lower steel bar strain and deflection compared to linear-arrangement hole form specimens. Additionally, specimens with concealed beam-type steel bar display lower steel bar strain and deflection than uniform-type steel bar specimens. However, the hole form and steel bar arrangement form have a limited impact on the ultimate load. Theoretical formulas for cracking load are provided for both fully composite and non-composite states. When compared to the experimental values, it is observed that the cracking load of the specimens with XPS panels closely matches the calculations for the non-composite state. An accurate prediction model for the ultimate load of fully composite wall panels is developed. These findings offer valuable insights into the behavior of composite sandwich wall panels and provide a basis for predicting their performance under various design factors and conditions.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.60 no.3
• /
• pp.71-81
• /
• 2018

$CO_2$ concentration has a significant effect on quality of cold-stored apples. High indoor $CO_2$ concentrations above 10,000 ppm cause the browning of apples and result in economic loss for farmers. The purpose of this study is to evaluate $CO_2$ concentrations and their distribution in a controlled atmosphere (CA) storage and provide better structural designs to improve the $CO_2$ environment using computational fluid dynamics (CFD) simulations. The CFD model was developed for a real CA storage for apples and applied to investigate the effect of changing the inlet and outlet locations and the aspect ratio of the floor of the CA storage on the spatial distributions of $CO_2$ concentration and the browning of the apples. The lowest $CO_2$ concentrations in existing CA storage with a high aspect ratio of the floor were achieved from the combination of the inlet located at the top of the right side and the outlet located at the bottom of the left side. In modified CA storage with a low aspect ratio, the combination of the inlet and outlet located at top and bottom of left side respectively achieved the lowest $CO_2$ concentrations. The proposed case enhanced the storage performance by reducing total browned apples by 3.6% in storage duration of 210 days. This study is expected to reduce the browning damages of apples in CA storage, and thus greatly prevent economic losses.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.128-138
• /
• 2022

In this study, in order to apply ultra-high-strength concrete beams of 100 MPa or more manufactured by centrifugal molding as the superstructure of the avalanche tunnel, the purpose is to verify the structural safety of the corner rigid joint in which the centrifugal molded beam is integrated with the substructure, which is the negative moment area. A full-size specimen was manufactured, and loading tests and analysis studies were performed. In order to expect the same effect that the maximum moment occurs in the corner joint part of the upper slab end when the standard model of the avalanche tunnel is designed with a load combination according to the specification, a modified cantilever type structural model specimen was manufactured and the corner rigid joint was fixedly connected. A study was performed to determine the performance of the method and the optimal connection construction method. The test results demonstrated that the proposed connection system outperforms others. Despite having differences in joint connection construction type, stable flexural behavior was shown in all the tested specimens. The proposed method also outperformed the behavior of centrifugally formed beams and upper slabs. The behavior of the corner rigid joint analysis model according to the F.E. analysis showed slightly greater stiffness compared to the results of the experiment, but the overall behavior was almost similar. Therefore, there is no structural problem in the construction of the corner rigid joint between the centrifugally formed beam and the wall developed in this study.

• Information Systems Review
• /
• v.7 no.2
• /
• pp.41-59
• /
• 2005

Mobile games have emerged as the most innovative entertainment technology adding new revenue streams, taking advantage of the potential of wireless consumer applications and service offerings. Mobile games, like any other types of computer game, offer a unique value for users in providing an exciting digital experience in virtual worlds. Players can become empowered through the development of new characters and strategies within games to achieve rewarding successes against the computers and other players. In this paper, we attempt to investigate the factors influencing the usage and acceptance of the mobile games in Korea, based on the extended version of the Technology Acceptance Model(TAM). Based on data collected from survey, we show that perceived usefulness is the major determinant for users to play mobile games. Two factors, including perceived enjoyment and self-expressiveness, are empirically shown to determine perceived usefulness. In addition, perceived ease of use, rewards, operational quality of device, and design/story have been showed to significantly and directly affect perceived enjoyment. It was also confirmed that self-efficacy and operational quality of device are the antecedents of perceived ease of use. Based upon the statistical results, some useful guidelines for game development and market penetration strategies are also provided.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.38 no.3
• /
• pp.64-77
• /
• 2015

An effective method for produce munitions effectiveness data is to calculate weapon effectiveness indices in the US military's Joint Munitions Effectiveness Manuals (JMEM) and take advantage of the damage evaluation model (GFSM) and weapon Effectiveness Evaluation Model (Matrix Evaluator). However, a study about the Range Safety that can be applied in the live firing exercises is very insufficient in the case of ROK military. The Range Safety program is an element of the US Army Safety Program, and is the program responsible for developing policies and guidance to ensure the safe operation of live-fire ranges. The methodology of Weapon Danger Zone (WDZ) program is based on a combination of weapon modeling/simulation data and actual impact data. Also, each WDZ incorporates a probability distribution function which provides the information necessary to perform a quantitative risk assessment to evaluate the relative risk of an identified profile. A study of method to establish for K-Range Safety data is to develop manuals (pamphlet) will be a standard to ensure the effective and safe fire training at the ROK military education and training and environmental conditions. For example, WDZs are generated with the WDZ tool as part of the RMTK (Range Managers Tool Kit) package. The WDZ tool is a Geographic Information System-based application that is available to operational planners and range safety manager of Army and Marine Corps in both desktop and web-based versions. K-Range Safety Program based on US data is reflected in the Korean terrain by operating environments and training doctrine etc, and the range safety data are made. Thus, verification process on modified variables data is required. K-Range Safety rather than being produced by a single program, is an package safety activities and measures through weapon danger zone tool, SRP (The Sustainable Range Program), manuals, doctrine, terrain, climate, military defence M&S, weapon system development/operational test evaluation and analysis to continuously improving range safety zone. Distribution of this K-range safety pamphlet is available to Army users in electronic media only and is intended for the standing army and army reserve. Also publication and distribution to authorized users for marine corps commands are indicated in the table of allowances for publications. Therefore, this study proposes an efficient K-Range Safety Manual producing to calculate the danger zones that can be applied to the ROK military's live fire training by introducing of US Army weapons danger zone program and Range Safety Manual

• Journal of the Korean Society of School Health
• /
• v.13 no.1
• /
• pp.117-129
• /
• 2000

The relationships between children's health behavior and variables that effect children's health behavior has been investigated in a number of previous studies. This study was conducted to examine the effects of a peer's social reinforcement on children's dental health behavior in an elementary school. The research design was a nonequivalent pre and post-test quasi-experimental design and the study subjects with one hundred and thirteen eight to nine years old children, and their mothers (57 experimental group, 56 control group) were selected as a study group. Subjects were selected by the convenience sampling method. The study was carried out in an elementary school in Namwon city, Korea, from the 26th of April to the 12th of June in 1999. Data were collected in both the pre and post-test portions. Using the "Health Belief Model", each item of the questionnaire for measurement of dental health behavior was modified and administered for the children and their mothers. The questionnaire for the measurement of dental health behavior was developed by Oh, Y.B.(1994). The Cronbach's ${\alpha}$ of the questionnaire for children were .81, and for the mother were .79. In this study, the health belief model consists of "perceived susceptibility", "perceived seriousness", "perceived barrier", "perceived salience", and "perceived benefit". The questionnaire for the children was composed of 37 items, and the questionnaire for the mother was composed of 40 items. Data were analyzed by frequency, ${\chi}^2-test$, ANOVA, Pearson's Correlation, and multiple regression analysis by a SAS program. The results of this study were summarized as follows ; 1. The first hypothesis that the experimental group would have more change in the frequency of brushing per week than that of control group was accepted(t=3.817, p=0.000). Mean tooth brushing scores in the experimental group improved significantly from pre-test to post-test, but in the control group there was no significant improvement in tooth brushing scores. 2. The second hypothesis that the experimental group would have more change in score of dental health behavior than that of control group was accepted(benefit : t=2.804, p=0.006, salience: t=2.608, p=0,010). An evaluation between the experimental group and the control group showed significant change from pre-test to post-test in health behavior scores. 3. The third hypothesis that higher scores of social reinforcement would create more change in the scores of tooth brushing frequency in the experimental group was accepted(${\beta}$=0.169, p=0.000. Multiple regression was used to examine the peer's social reinforcement scores and the relative influence of significant variables in previous ANOVA and Pearson's correlation test on children's frequency of brushing during the post-test. The results of the study indicated that the combination of social reinforcement of peers with variables pertaining to mother and householder were significantly related and effectively improved a child's tooth brushing.