• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.313-319
• /
• 1999

The development of deformation texture in FCC polycystalline metals during rolling was simulated by the finite element analysis using a large-deformation, elaatic-plastic, rate-dependent polycrystalline model of crystal plasticity. Different plastic anisotropy due to different orientation of each crystal makes inhomogeneous deformation. Assuming plane strain compression condition, the simulation with a high rate sensitivity resulted in main component change from Dillamore at low rate sensitivity to Brass component.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.1029-1034
• /
• 2003

The basic Physical properties, Slump, Slump Flow, Air content, Bleeding, and Settlement of concrete was investigateed to test Characteristic of Setting and to evaluate the relation between Model Specimen and Heat of hydration for construction Over the High Temperature (CFT). The objective of this study is to take the partial core after the cementation of Model Specimen, test the compression intensity and analyze the relation to Test Piece.

• Structural Engineering and Mechanics
• /
• v.37 no.6
• /
• pp.649-669
• /
• 2011

In this paper an analytical model is presented that addresses the compressive response of short-fiber reinforced concrete members (FRC) with hooked steel fibers. This model is applicable to a wide range of concrete strengths and accounts for the interaction between the cover spalling and the concrete core confinement induced by transverse steel stirrups and also for buckling of longitudinal reinforcing bars. The load-shortening curves generated here analytically fit existing experimental data well.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.20 no.43
• /
• pp.197-204
• /
• 1997

Torques on each joint, the compression on L5/S1 disc, the force on hand of a rider are estimated using a static biomechnic model. Forces that the rider applies to the pedals, saddle and handle during starting and speeding are estimated using static mechanics. Physical stress is considered accroding to handle height and horizontal distance between handle and pedal. When handle height is higher in normal speeding, the force on handle and sum of torques on each joint decreases.

• Journal of Ocean Engineering and Technology
• /
• v.4 no.2
• /
• pp.15-21
• /
• 1990

This study focuses the mechanical deformation response predicted by the plasticity model for polycrystalline ice. To describe various deformation characteristics, ice is idealized as a perfectly plastic material using an asymptotic exponential failure criterion. This criterion is suite for describing materials which exhibit brittle deformation at low hydrostatic pressure and ductile deformation at high hydrostatic pressure. The results are compared to those of continuum damage mechanics model. Plasticity model shows good agreement with damage model and experimental results for high confining pressures even at high strain-rates which is usually considered as a brittle condition under uniaxial compression.

• Journal of Ocean Engineering and Technology
• /
• v.4 no.2
• /
• pp.165-165
• /
• 1990

This study focuses the mechanical deformation response predicted by the plasticity model for polycrystalline ice. To describe various deformation characteristics, ice is idealized as a perfectly plastic material using an asymptotic exponential failure criterion. This criterion is suite for describing materials which exhibit brittle deformation at low hydrostatic pressure and ductile deformation at high hydrostatic pressure. The results are compared to those of continuum damage mechanics model. Plasticity model shows good agreement with damage model and experimental results for high confining pressures even at high strain-rates which is usually considered as a brittle condition under uniaxial compression.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.3
• /
• pp.615-619
• /
• 2007

In this study, the MCC(modified Cam-Clay) model and the Hvorslev-MCC model, recently developed based on the critical state theory and with relatively few model parameters, were investigated by comparing the model predictions with the result of the conventional triaxial compression test strictly performed in laboratory. The discrepancy of the prediction capacities of the models exists on the heavily over-consolidated specimen. The Hvorslev-MCC model accurately predicts the peak strength envelope for heavily over-consolidated clayey specimens on the dry side of the critical state since it adopts the Hvorslev surface in the supercritical region other than the ellipse of the MCC model.

• Transactions of Materials Processing
• /
• v.22 no.6
• /
• pp.303-309
• /
• 2013

Spring-back of MS1470 steel sheets was numerically predicted using a non-linear kinematic hardening material behavior based on the Yoshida-Uemori model. From uniaxial tension and uniaxial tension-compression-tension data as well as the uniaxial tension-unloading-tension data, the parameters of the Yoshida-Uemori model were obtained. For the numerical simulations, the Yoshida-Uemori model was implemented into the commercial finite element program, ABAQUS/Explicit and ABAQUS/Standard using the user-defined material subroutines. The model performance was validated against the measured spring-back from the benchmark problems of NUMISHEET 2008 and NUMISHEET 2011, the 2-D draw bending test and the S-rail forming test, respectively.

• International Journal of Railway
• /
• v.3 no.4
• /
• pp.117-122
• /
• 2010

In transportation geotechnical engineering, stress-strain behavior of earth structures has been analyzed by numerical simulations with the implemented plasticity constitutive model. It is a fact that many advanced plasticity constitutive models on predicting the mechanical behavior of soils have been developed as well as experimental research works for geotechnical applications in the past decades. In this study, recently developed, a unified constitutive model for both clay and sand, which is referred to as CASM (clay and sand model), was compared with a classical constitutive model, Cam-Clay model. Moreover, integration methods of stress-strain rate equations using CASM were presented for simulation of undrained and drained triaxial compression tests. As a conclusion, it was observed that semi-implicit integration method has more improved accuracy of capturing strain rate response to applied stress than explicit integration by the multiple correction and iteration.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.41-48
• /
• 2002

The fact that nonlinearity and anisotropy of soil should be considered for the proper estimation of soil deformation has been recongnized for a long time. In this study, a new stiffness model which can reflect both nonlinearity and anisotropy is proposed. Nonlinearity is simulated by Ramberg-Osgood model and anisotropy is modeled with the cross-anisotropic elasticity. Analysis results with the developed model compared with those from analyses using linear isotropic model, linear anisotropic model, and nonlinear isotropic model. In the triaxial compression like condition, the effects of nonlinearity on the vertical strain are significant, but soil anisotropy does not affect the vertical strain. In 1-dimensional deformation condition, however, both nonlinearity and anisotropy of soil influence the final magnitude of the vertical strain. Also the increase of poisson's ratio magnifies the effect of anisotropy on the vertical strain in this condition.