• Membrane and Water Treatment
• /
• 제8권5호
• /
• pp.449-462
• /
• 2017

Direct treatment of municipal wastewater by forward osmosis (FO) process was evaluated in terms of water flux decline, reverse salt diffusion, pollutants rejection and concentration efficiency by using synthetic seawater as the draw solution. It was found that when operating in PRO mode (active layer facing the draw solution), although the FO membrane exhibited higher osmotic water flux, more severe flux decline and reverse salt diffusion was also observed due to the more severe fouling of pollutants in the membrane support layer and accompanied fouling enhanced concentration polarization. In addition, although the water flux decline was shown to be lower for the FO mode (active layer facing the feed solution), irreversible membrane fouling was identified in both PRO and FO modes as the water flux cannot be restored to the initial value by physical flushing, highlighting the necessity of chemical cleaning in long-term operation. During the 7 cycles of filtration conducted in the experiments, the FO membrane exhibited considerably high rejection for TOC, COD, TP and $NH_4{^+}-N$ present in the wastewater. By optimizing the volume ratio of seawater draw solution/wastewater feed solution, a concentration factor of 3.1 and 3.7 was obtained for the FO and PRO modes, respectively. The results demonstrated the validity of the FO process for direct treatment of municipal wastewater by using seawater as the draw solution, while facilitating the subsequent utilization of concentrated wastewater for bioenergy production, which may have special implications for the coastline areas.

• 디지털융복합연구
• /
• 제19권8호
• /
• pp.293-299
• /
• 2021

게임산업 OSMU모델의 발전으로 중국에서 가장 인기가 높은 3D 모바일 게임 '왕자영요'는 게임 자체의 엔터테인먼트 효과 외에, 근년에 홍보 애니메이션 영상 콘텐츠의 제작을 더욱 중시하고 있다. 거대한 애니메이션 시장은 모바일 게임 <왕자영요>에 풍부한 게임 수익과 함께 많은 신규 이용자들이 발생하고 있다. 본 논문은 <왕자영요> 공식 스토리 스테이션 내 30개의 CG 홍보 애니메이션 단편영화에 대한 조사를 통해 최근에 가장 인기 있는 게임 홍보 애니메이션 <목표>와 <불야장안>을 선정하였고, 애니메이션의 특징 분석으로는 풍부한 스토리, 화려한 장면의 특수효과 등 중요 요소들에 대해 정리하였다. 본 논문연구를 통해 게임 산업에서 홍보용 애니메이션 콘텐츠의 중요성을 파악하였으며, 또한 이를 통해 게임 산업과 애니메이션 산업의 동반성장을 기대할 수 있으며 게임시장의 높은 수익을 창출하는 방법 중 하나임을 알 수 있었다.

• International Journal of Fluid Machinery and Systems
• /
• 제9권2호
• /
• pp.182-193
• /
• 2016

Introduction of intermittent electricity production systems like wind and solar power to electricity market together with the deregulation of electricity markets resulted in numerous start/stops, load variations and off-design operation of water turbines. Hydraulic turbines suffer from the varying loads exerted on their stationary and rotating parts during load variations since they are not designed for such operating conditions. Investigations on part load operation of single regulated turbines, i.e., Francis and propeller, proved the formation of a rotating vortex rope (RVR) in the draft tube. The RVR induces pressure pulsations in the axial and rotating directions called plunging and rotating modes, respectively. This results in oscillating forces with two different frequencies on the runner blades, bearings and other rotating parts of the turbine. This study investigates the effect of transient operations on the pressure fluctuations exerted on the runner and mechanism of the RVR formation/mitigation. Draft tube and runner blades of the Porjus U9 model, a Kaplan turbine, were equipped with pressure sensors for this purpose. The model was run in off-cam mode during different load variations. The results showed that the transients between the best efficiency point and the high load occurs in a smooth way. However, during transitions to the part load a RVR forms in the draft tube which induces high level of fluctuations with two frequencies on the runner; plunging and rotating mode. Formation of the RVR during the load rejections coincides with sudden pressure change on the runner while its mitigation occurs in a smooth way.

• Asian-Australasian Journal of Animal Sciences
• /
• 제30권1호
• /
• pp.8-19
• /
• 2017

Objective: A whole genome association study was conducted to identify single nucleotide polymorphisms (SNPs) with additive and dominant effects for growth and carcass traits in Korean native cattle, Hanwoo. Methods: The data set comprised 61 sires and their 486 Hanwoo steers that were born between spring of 2005 and fall of 2007. The steers were genotyped with the 35,968 SNPs that were embedded in the Illumina bovine SNP 50K beadchip and six growth and carcass quality traits were measured for the steers. A series of lack-of-fit tests between the models was applied to classify gene expression pattern as additive or dominant. Results: A total of 18 (0), 15 (3), 12 (8), 15 (18), 11 (7), and 21 (1) SNPs were detected at the 5% chromosome (genome) - wise level for weaning weight (WWT), yearling weight (YWT), carcass weight (CWT), backfat thickness (BFT), longissimus dorsi muscle area (LMA) and marbling score, respectively. Among the significant 129 SNPs, 56 SNPs had additive effects, 20 SNPs dominance effects, and 53 SNPs both additive and dominance effects, suggesting that dominance inheritance mode be considered in genetic improvement for growth and carcass quality in Hanwoo. The significant SNPs were located at 33 quantitative trait locus (QTL) regions on 18 Bos Taurus chromosomes (i.e. BTA 3, 4, 5, 6, 7, 9, 11, 12, 13, 14, 16, 17, 18, 20, 23, 26, 28, and 29) were detected. There is strong evidence that BTA14 is the key chromosome affecting CWT. Also, BTA20 is the key chromosome for almost all traits measured (WWT, YWT, LMA). Conclusion: The application of various additive and dominance SNP models enabled better characterization of SNP inheritance mode for growth and carcass quality traits in Hanwoo, and many of the detected SNPs or QTL had dominance effects, suggesting that dominance be considered for the whole-genome SNPs data and implementation of successive molecular breeding schemes in Hanwoo.

• 한국자동차공학회논문집
• /
• 제15권3호
• /
• pp.133-140
• /
• 2007

The purpose of this study was to evaluate the effects of gasoline fuel to the LPI engine. Firing test bench was used in order to assess the effect on gasoline-injected LPI engine. Gasoline fuel was supplied into the reverse direction(3-4-2-1 cylinder) at 3.0 bar with commercial gasoline fuel pump. Engine test was performed using the firing test mode at end of line. The deviations of excess air ratio of each cylinder and maximum combustion pressure using gasoline fuel were within 0.1 and $1{\sim}2\;bar$. Engine start time was measured with changing coolant temperature at $20^{\circ}C,\;40^{\circ}C,\;80^{\circ}C$, respectively. Residual gasoline volume in the fuel line was measured about 32 cc after firing test and it was less than 2 cc within 10 seconds purging. To simulate the end of line, the residual gasoline in the fuel line was purged during 5 and 10 seconds. Start time of LPI engine with LPG fuel were 0.61 and 0.58 seconds. This work showed that severe problems such as misfiring and liner scuffing were not occurred applying gasoline fuel to LPI engine.

• 한국수산과학회지
• /
• 제37권4호
• /
• pp.330-336
• /
• 2004

To meet the increasing demand from various fishing fields for training of fishing equipment operators, a fishing winch simulator was designed to train maritime students in the correct and safe operation of hydraulic winches under various load conditions related to fishing operations. The aim of this study is to describe the basic dynamic characteristics of the newly developed hydraulic fishing winch simulator and particularly to analyze the mechanical responses produced on the winch operation controls. The winch simulator consists of two winch units, a computer control and data acquisition system, a control consol and other associated mechanisms. When one winch is in hauling mode, the other one will always be in loading mode. The revolution speed of the hauling winch was controlled by a proportional directional control valve, and the braking torque of the loading winch was controlled by a proportional pressure control valve. The simulation experiments indicated that the dynamic characteristics of the hauling winch followed the braking response characteristics of the loading winch. The tests also showed that the warp speed and tension linearly depend on the pressure differential across the motor of the loading winch controlled by operating the proportional pressure control valve during the hauling operation. The experience gained from various training courses showed that the fishing winch simulator was very realistic and it was valuable for training novice winch operators. The results of the winch simulation exercise were recorded and used to evaluate the training on the operation and handling of the winch system. From these test results, we concluded that the tension acting on the warp during hauling operations can successfully be simulated by controlling the pressure differential across the motor with step changes of the control input signal to the proportional pressure control valve of the loading winch.

• 한국패션뷰티학회지
• /
• 제1권1호
• /
• pp.65-78
• /
• 2003

This research is to provide practical help in learning hair and makeup illustration skills by presenting techniques for hair and makeup drawing; to serve efficient illustration education; and to enhance the status of beauty and contribute to artistic development. Hair style and makeup techniques include graphical one, pattern-centered one, one using pattern paper, simplifying one and mood one expressing image. Of them, this research made the illustrations to use cosmetics, color pencils and pastel based on the graphical technique. for each design of the illustrations, ethnic, sexy, natural, romantic and gorgeous images, which were considered to be appropriate to the graphical technique, were chosen by the researcher out of hair and makeup styles that appeared in the fashion magazines including Vogue, Gap, Mode et Mode from 2000 through 2001. In particular, they were chosen with focusing on basic styles. The summaries below were found with the experience of making illustrations. Various techniques and skills are required to express the ideas of hair and makeup styles. Of them, the graphical technique is very useful as the primary step to learn various techniques and improve drawing skills. First, the graphical technique may enable not only expressing what is desired to draw as is, but also accurately representing hair and makeup designs so as to convey objective expression. In this regard, it is a proper way to achieve its inherent purpose as conveyance of messages. Second, more accurate styling of hair and makeup is available through graphical expression, which helps understand related practical techniques. In addition, makeup illustration, which is expressed through direct makeup products and instruments, may serve skill improvement since such direct use provides the feeling of real makeup. Third, the graphical technique as a basic drawing skill may unrestrictedly show the artist's expression ability. Fourth, although artistic merits implying individuality and creativity should be shared through illustrations that express the artist's ideas or emotions, the graphical technique is the easiest method to beginners who just started learning of illustration, in that it enables expression without highly advanced skills.

• Asian-Australasian Journal of Animal Sciences
• /
• 제24권3호
• /
• pp.330-335
• /
• 2011

The mode of inheritance of total milk yield and its genetic parameters were investigated in Churra dairy sheep through segregation analyses using a Monte Carlo Markov Chains (MCMC) method. Data which consisted of 7,126 lactations belonging to 5,154 ewes were collected between 1999 and 2002 from 15 Spanish Churra dairy flocks. A postulated major gene was assumed to be additive and priors used for variance components were uniform. Based on 50 000 Gibbs samples from ten replicates chains of 100,000 cycles, the estimated marginal posterior means${\pm}$posterior standard deviations of variance components of milk yield were $23.17{\pm}18.42$, $65.20{\pm}25.05$, $120.40{\pm}42.12$ and $420.83{\pm}40.26$ for major gene variance ($\sigma_G^2$), polygenic variance ($\sigma_u^2$), permanent environmental variance ($\sigma_{pe}^2$) and error variance ($\sigma_e^2$), respectively. The results of this study showed the postulated major locus was not significant, and the 95% highest posterior density regions ($HPDs_{95%}$) of most major gene parameters included 0, and particularly for the major gene variance. The estimated transmission probabilities for the 95% highest posterior density regions ($HPDs_{95%}$) were overlapped. These results indicated that segregation of a major gene was unlikely and that the mode of inheritance of total milk yield in Churra dairy sheep is purely polygenic. Based on 50,000 Gibbs samples from ten replicates chains of 100,000 cycles, the estimated polygenic heritability and repeatability were $h^2=0.20{\pm}0.05$ and r=$0.34{\pm}0.06$, respectively.

• 한국통신학회논문지
• /
• 제40권1호
• /
• pp.183-186
• /
• 2015

최근 들어 선박 내 안전과 정보전달 시스템 구축에 대한 수요가 증대하고 있다. 선박 내에 기 구축된 유선망을 활용하는 방안이 있으나 이는 새로운 배선을 해야 하고 구조물의 일부를 불가피하게 변형해야 하고 이에 따른 구축시간의 증가와 비용증가가 크므로 이에 따른 무선 감지기 망을 구축함으로써 비용과 구축시간을 단축할 수 있다. 이 논문에서는 선박 내 무선신호전달 특성을 측정하고 분석하는데 적합한 서명 수열-양방향 패킷 방식 기반 선내 전파전달측정 시스템을 설계하고 모의 실험을 통해 검증한 뒤, 구성된 시스템을 기반으로 측정한 데이터를 분석한다. 이와 같은 선내 채널 측정시스템을 활용함으로써 신뢰성 있고 비용효율적인 선박 내 무선 망을 구성할 수 있을 것으로 기대한다.

• 수산해양기술연구
• /
• 제46권2호
• /
• pp.157-163
• /
• 2010

The indirect target strength (TS) estimation method which uses the Kirchhoff ray mode model (KRM model) was discussed to apply for a biomass estimation in the water of mixed species. TS of 25 live scorpion fishes for 120kHz were measured by a tethered method and of others dominant 5 species in the marine ranching ground of Jeju coastal water including a scorpion fish were also estimated by KRM model. The measurement TS of scorpion fish well agreed with the theoretical values and the standard formula of scorpion fish was estimated as $TS_{120kHz}=20Log\;(L)-72.9$ ($r^2=0.67$). TScm values estimated on trial to each sample of dominant 5 species were from -69.3dB to -75.1dB at 120kHz and they were in the general range of swimbladdered fish. It was clarified that TS by KRM model can be used to estimate fish biomass estimation by increasing a sample number and is more effective under the condition that there is rare TS information for inhabiting species in mixed-species area.