• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.4
• /
• pp.156-159
• /
• 2007

The red emission properties of $Mn^{4+}$ doped $SrAl_{12}O_{19}$ prepared by the solid-state reaction was investigated, in order to verify its potential to act as the red emitting phosphor of white LEDs. The emission spectrum exhibits a narrow band between $600{\sim}700 nm $ with four sharp peaks occurring at about 643, 656, 666, 671 nm due to the $^2E\to^4A_2$ transition of $Mn^{4+}$. The excitation spectrum exhibits a broad band between $200{\sim}500 nm$ with three peaks occurring at about 338, 398 and 468 nm, respectively. Moreover, the relative emission intensity of $SrAl_{12}O_{19}:Mn^{4+}$ with or without $CaF_2$ and MgO fluxes measured at excitation source 390 nm. The relative emission intensity of $SrAl_{12}O_{19}:Mn^{4+}$ containing 0.67mol% MgO was approximately 30% higher than that of the base composition sample. Strontium hexa-aluminate measured at room temperature as a function of the substituted Mg concentration. MgO was added to replace part of the $Al_2O_3$. Also, the relative emission intensity of $SrAl_{12}O_{19}:Mn^{4+}$ containing 0.67 mol% MgO and 0.67 mol% $CaF_2$ was approximately about 48% higher than that of the base composition $SrAl_{12}O_{19}:Mn^{4+}$.

• Journal of the Korean Ceramic Society
• /
• v.37 no.6
• /
• pp.552-558
• /
• 2000

LiMn2O4 thin fiolm cathodes for Li-ion secondary battery were fabricated by r.f. magnetron sputtering technique. As-deposited films were amorphous. A spinel structure could not be obtained LiMn2O4 films by in-situ thermal annealing. After post thermal annealing over $700^{\circ}C$ in oxygen atmosphere, LiMn2O4 films prepared above 100 W r.f. power could be crystallized into a spinel structure. The electrochemical property of the LiMn2O4 film cathodes was tested in a Li/1 M LiClO4 in PC/LiMn2O4 cell. From cyclic voltammetry at scan rate of 2mV/sec of 2.5~4.5V, LiMn2O4 electrode prepared by post annealing at 75$0^{\circ}C$ showed good initial capacity. LiMn2O4 electrode prepared by post annealing at 80$0^{\circ}C$ showed the best crycling performance.

• Elastomers and Composites
• /
• v.53 no.2
• /
• pp.75-79
• /
• 2018

ZnS:Mn-glycine (ZnS:Mn-Gly) nanocomposites were synthesized by capping ZnS:Mn nanocomposites with glycine. Zinc sulfate heptahydrate ($ZnSO_4{\cdot}7H_2O$), glycine ($C_2H_5NO_2$), manganese sulfate monohydrate ($MnSO_4{\cdot}H_2O$), and sodium sulfide ($Na_2S$) were used as the source reagents. $ZnS:Mn-Gly-C_{60}$ nanocomposites were obtained by heating the ZnS:Mn-Gly nanocomposites and fullerene ($C_{60}$) at a 2:1 mass ratio in an electric furnace at $700^{\circ}C$ for 2 h. X-ray diffraction (XRD) was used to characterize the crystal structure of the synthesized nanocomposites. The photocatalytic activity of the $ZnS:Mn-Gly-C_{60}$ nanocomposites was evaluated, via the degradation of brilliant green (BG) dye under 254 nm irradiation, with a UV-vis spectrophotometer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.2
• /
• pp.245-250
• /
• 1999

The effect of cation substitution on the inonic conductivity was studied in $(Li_{0.5}La_{0.5})_{1-y}Sr_yTi_{1-x}Mn_xO_3$ system. In case of Sr substitution, the ionic conductivity abrubtly decreased over y=0.05. This may be caused by the decrease of lithium contents which contribute to lithium inonic conductivity. Jahn-Teller distortion as well as lattice parameter variation influenced the inonic conductivity in case of Mn substitution. A and B-site cations effects on the conductivities were found to be independent, and the ionic conductivity as high as $2.8{\times}10^{-2}$S/cm was obtained in x=0.0006 and y=0.05.

• Applied Microscopy
• /
• v.45 no.1
• /
• pp.9-15
• /
• 2015

In the present study, microstructural evolution in CuCrFeNi, CuCrFeNiMn, and CuCrFeNiMnAl alloys has been investigated. The as-cast CuCrFeNi alloy consists of a single fcc phase with the lattice parameter of 0.358 nm, while the as-cast CuCrFeNiMn alloy consists of (bcc+fcc1+fcc2) phases with lattice parameters of 0.287 nm, 0.366 nm, and 0.361 nm. The heat treatment of the cast CuCrFeNiMn alloy results in the different type of microstructure depending on the heat treatment temperature. At $900^{\circ}C$ a new thermodynamically stable phase appears instead of the bcc solid solution phase, while at $1,000^{\circ}C$, the heat treated microstructure is almost same as that in the as-cast state. The addition of Al in CuCrFeNiMn alloy changes the constituent phases from (fcc1+fcc2+bcc) to (bcc1+bcc2).

• Journal of the Korean Ceramic Society
• /
• v.15 no.1
• /
• pp.9-15
• /
• 1978

The possiblity of mullitization from the domestic alunite by adding of $Fe_2O_3-MnO_2$, $Fe_2O_3-MnO_2-TiO_2$, $Fe_2O_3-MnO_2-CaF_2$, and $Fe_2O_3-MnO_2-CaF_2-TiO_2$ mixtures as mineralizers was studied at the temperature range between $1, 250^{\circ}C$~$1, 430^{\circ}C$. The modifying method of domestic alunite was performed by calcination, wet ballmilling, and washing with water. The following results were obtained; 1) When added of 3.0% $Fe_2O_3$ plus 1.0-1.5% $MnO_2$ to modified alunite, the appropriate temperature range of mullite-forming was $1, 350^{\circ}C$-$1, 400^{\circ}C$. 2) When added of $TiO_2$ as mineralizer, the mullite-forming temperature was higher than not added. 3) When added of $CaF_2$ as mineralizer, the synthesized mullite was resolve at the temperature above $1, 350^{\circ}C$.

• Journal of the Korean Magnetics Society
• /
• v.19 no.4
• /
• pp.133-137
• /
• 2009

$MnGeP_2$ thin films grown on GaAs exhibit room-temperature ferromagnetism with $T_C{\sim}$320 K, based on both magnetization and resistance measurements. The coercive fields at 5, 250, and 300 K are 3870, 1380 and 155 Oe, respectively. The anomalous Hall effect was observed, indicating spin polarization of the carriers. Hysteresis has been observed in both magnetoresistance and Hall measurements. The current-voltage characteristics of a $MnGeP_2$ film grown on an n-type GaAs substrate display semiconducting behavior.

• Journal of the Korean Ceramic Society
• /
• v.55 no.1
• /
• pp.21-35
• /
• 2018

Spinel $LiNi_{0.5}Mn_{1.5}O_4$ has received great attention as one of the most outstanding cathode materials for Li-ion batteries (LIBs) because of its high energy density resulting from the operating voltage of ~ 4.7 V (vs. $Li^+/Li$) based on the $Ni^{2+}/Ni^{4+}$ redox reaction. However, $LiNi_{0.5}Mn_{1.5}O_4$ is known to suffer from undesirable side reactions with the electrolyte at high voltage as well as Mn dissolution from the structure. These issues prevent the realization of the optimal electrochemical performance of $LiNi_{0.5}Mn_{1.5}O_4$. Extensive research has been conducted to overcome these issues. This review presents an overview of the various surface-modification methods available to improve the electrochemical properties of $LiNi_{0.5}Mn_{1.5}O_4$ and provides perspectives on further research aimed at the application of $LiNi_{0.5}Mn_{1.5}O_4$ as a cathode material in commercialized LIBs.

• Journal of Life Science
• /
• v.15 no.1 s.68
• /
• pp.94-99
• /
• 2005

Sixty four bacterial colonies which were able to oxidize the manganese were isolated from soil samples in Mokcheon and Ochang area. Among them, one bacterial strain was selected for this study based on its higher manganese oxidation, and this selected bacterial strain was identified as Aeromonas sp. MN44 through physiological-biochemical test and analysis of its 16s rRNA sequence. Aeromonas sp. MN44 was able to utilize lactose but did not utilize various carbohydrates as a sole carbon source. Aeromonas sp. MN44 showed a very sensitive to antibiotics such as kanamycin, chloramphenicol, ampicillin, tetracycline and spectinomycin, and heavy metal such as cadmium. But this strain showed a high resistance up to mg/ml unit to heavy metals such as lithium and manganese. Optimal manganese oxidation condition of Aeromonas sp. MN44 was pH 7.4 and manganese oxidation activity was inhibited by proteinase K and boiling treatment. So, we concluded that this factor was protein. The manganese oxidizing factor produced by Aeromonas sp. MN44 was partial purified by ammonium sulfate precipitation, DEAE-Toyopearl 650M ion exchange chromatography and Sephadex gel filtration chromatography. Its molecular mass was about 113 kDa.

• Resources Recycling
• /
• v.21 no.3
• /
• pp.21-27
• /
• 2012

In order to make high-purity ferro-manganese from $Mn_3O_4$ dust, the application of aluminothermy process to the reduction of $Mn_3O_4$ dust was investigated in previous work. The result showed the fact that can be obtained high purity ferro-manganese which have over about 93% of manganese content and lower impurities such as C, P, S than those of KS D3712 specification. The addition of silicon powder instead of aluminum powder was investigated as reductant in the thermite reaction process of $Mn_3O_4$ dust in this work because its production cost is lower than that of aluminum powder. In case of addition of silicon powder only as reductant, the experimental result showed the unstable ignition and no thermite reaction of mixture, but in case of simultaneous addition of silicon and aluminum powders as reductant, showed the fact that can be obtained high purity ferro-manganese which have much low content of impurities such as C, P, S component.