• Magazine of the Korean Society of Agricultural Engineers
• /
• v.22 no.3
• /
• pp.46-59
• /
• 1980

This study was conducted to obtain the most effective distribution of grain size and the optimum lime content for lime-soil stabilization. To achieve the aim, the change of consistency, the characteristics of compaction and unconfined compressive strength were tested by adding of 0, 4, 6, 8, 10 and 12 percent lime by weight for all soils adjusted by given ratios of sand to clay. The results obtained were as follows; 1. There was a tendency that the plasticity index of lime-soil mixture was decreased by increasing the amount of lime, whereas the liquid limit was varied irregularly and the plastic limit was increased. 2. With the addition of more lime, the optimum moisture content of lime-soil mixture was increased, and the maximum dry density was decreased. 3. The optimum lime content of lime-soil mixture was varied from soil to soil, and the less amount of small grain size, the less value of optimum lime content. 4. The optimum distribution of grain size for lime-soil mixture was in the soil, having the ratio of about 60 percent of cohesive clay and about 40 percent of sand by weight. 5. In the soil having fine grain size, the effect of curing appeared for long periods of time, whereas the increasing rate of unconfined compressive strength was great on the soil of coarse grain size in the earlier stage of curing period.

• Journal of Environmental Health Sciences
• /
• v.35 no.6
• /
• pp.510-516
• /
• 2009

Polybrominated diphenyl ethers (PBDEs) and polychlorinated biphenyls (PCBs) were measured in soil samples of Ansung in Kyonggi-province to investigate concentration distribution of PBDEs and PCBs. The 10 soil samples were collected using a stainless steel hand-held corer that was cleaned before and after each sample using hexane. Total concentration of PBDE and PCBs were 2,205.3 and 348.1 pg/g dry weight (DW) in soil sample, respectively. BDE-209 showed as the most abundant congener in soil samples which was related to imported amount and usage amount of deca-BDE technical mixture in Korea. Also, BDE-99, BDE-47, BDE-100 deposition in soil sample was higher than other congeners and was related to the imported and usage amount reported for penta-BDE technical mixture in Korea. Correlation coefficient between PBDE contribution and technical mixture formulation (Bromokal 70-5DE) were significant (r=0.91, p<0.01) which suggests the influence of sources in this technical mixtures.

• International Journal of Reliability and Applications
• /
• v.10 no.2
• /
• pp.63-79
• /
• 2009

A new bivariate linear failure rate distribution is introduced through a shock model. It is proved that the marginal distributions of this new bivariate distribution are linear failure rate distributions. The joint moment generating function of the bivariate distribution is derived. Mixtures of bivariate linear failure rate distributions are also discussed. Application to a real data is given.

• The Korean Journal of Applied Statistics
• /
• v.8 no.1
• /
• pp.159-167
• /
• 1995

Considering special discrete distribution of exponential family as a sequence with respect to the points of support, the squence is unimodal in some sense. In this paper, we study under what condition the mixture of that discrete distribution with respect to a parameter is unimodal. We derive the maximal interval of the parameter in which each mixture of the discrete distribution such as Binomial and Poisson is always unimodal.

• Transactions of Materials Processing
• /
• v.8 no.4
• /
• pp.399-406
• /
• 1999

It is more appropriate to treat that the semi-solid mixture as a single phase material that obeys incompressibility in the global sense and to analyze the liquid flow only locally than the approach based on compressible yield criteria. In the present study, a numerical algorithm of updating the solid volume fraction based on mixture theory has been developed. Finite element analysis of simple upsetting was carried out using the proposed algorithm to investigate the degree of macro-segregation according to friction conditions and compressive strain rates under the isothermal condition. The simulation results were compared to experimental results available in reference to test the validity of the currently proposed algorithm. Since the comparison results show a good agreement it is construed that the proposed algorithm can contribute to the development of numerical analysis of determining the solid volume fraction semi-solid processing.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.79-85
• /
• 2005

This work is to investigate the surface heat flux and combustion characteristics of premixed propane mixture in a constant volume chamber. The experiment of heat flux and combustion characteristics of premixed propane mixture are performed with various equivalence ratio and initial pressure conditions. Based on the experimental results, it is found that the maximum instantaneous temperature is increased with the increase of initial pressure in the chamber. There are significant differences in the burning velocity of premixed propane mixture at different measuring points in the constant volume combustion chamber. A]so, the trends of temperature difference at each measuring points are similar to the burning velocity in the combustion chamber. It is concluded that the total heat loss during the combustion period is affected by the equivalence ratio and the initial condition of fuel-air mixture.

• Macromolecular Research
• /
• v.17 no.7
• /
• pp.483-490
• /
• 2009

Stable poly(styrene-co-divinylbenzene) [P(St-co-DVB)] micro spheres with narrow size distribution were synthesized in the presence of 2,2'-azobis(2,4-dimethyl valeronitrile) (V-65) and co-initiator in an acetone/water mixture in the precipitation polymerization at $53^{\circ}C$ for 24 h. Potassium peroxodisulfate (KPS), ammonium peroxodisulfate (APS) and sodium peroxodisulfate (NaPS) were used as co-initiators. The optimum ratio of acetone to water for the formation of a narrow distribution of P(St-co-DVB) particles was 49:11 (g/g). The optimum co-initiator compositions for narrow distribution were 9:1 (g/g) for V-65 to KPS, 11:1 for V-65 to APS and 6:1 for V-65 to NaPS. The yield for these compositions was $54{\sim}57%$ and the largest particle size was obtained with the lowest zeta-potential and CV values. From the XPS measurements, the charge density was increased but the zeta potential decreased with increasing sulfur content, implying that the sulfate group provides the electrostatic stabilization on the particle surface. This suggested that the self-crosslinking between styrene and DVB, the electrostatic stabilization of initiators, and the balanced hydrophobic and hydrophilic properties of the solvents are responsible for the formation of stable P(St-co-DVB) spherical particles with narrow size distribution.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.5
• /
• pp.72-79
• /
• 2003

Spray characteristics were investigated by impinging F-O-O-F type injector with varying the impingement angle through 15, 20 and 30 degree and the mixture ratio(O/F ratio) from 1.5 to 3.0. Experimental results show that the correlation between dispersion and impingement angle is not influenced of the mixture ratio variation, but which has influence on number density, and there is a linear correlation between dispersion and impingement angle. Velocity distribution, standard deviation and SMD of droplets are decreased as the impingement angle increases. Also, it was confirmed that the distribution of droplet size are in accordance with Rosin-Rammler and Upper-limit distribution.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.17 no.1
• /
• pp.27-34
• /
• 1997

This experiment was carried out to determine growth characteristics, dry matter (DM) yield, seasonal yield distribution and nutritive value of early- and late maturity orchardgrass, 1990 to 1992. The cultivars used in this study were Potomac, Hallmark (early maturing cultivar) and Lidacta, Rancho (late maturing cultivar), and a mixture plot (Potomac 25% + Hallmark 25% + Lidacta 25% + Rancho 25%) was involved. The seeding rate was 20 kgha in all treatments. Plant height of Potomac and Hallmark was longer than that of Lidacta and Rancho. The dates of initial heading and 50% heading of early maturing cultivars (Apr. 30 and May 10) were 10 days earlier than those of late matuing cultivars. Potomac and Hallmark were upright, and Lidacta and Rancho were semi-upright type, and severe disease and weeds (30 ~ 40%) were observed at Lidacta plot. On an average of three years, the DM yields of Potomac (10,549 kglna), Hallmark (10,435 kg) and mixture (10,356 kg) were significantly (P<0.05) higher than those of Rancho (9,457 kg) and Lidacta (8,218 kg). However, seasonal yield distribution of late maturing cultivars was better than that of early maturing cultivars. The contents of crude protein, crude fat, crude fiber, nitrogen %ee extract, aude ash, neutral detergent fiber, P, K, Ca, and Mg were not significantly different between cultivars, but higher aude protein yield was found at Potomac, Hallmark and mixture plots. Based on the above results, it may be concluded that early maturing cultivars for high productivity, late maturing cultivars for seasonal yield distribution, and seeding of mixture andlor separation of early- and late maturing cultivars are recommended. Also Lidacta was a not promising cultivar due to low productivity, severe disease, and high weeds development.

• Nuclear Engineering and Technology
• /
• v.48 no.4
• /
• pp.881-892
• /
• 2016

Following the Fukushima accident and its extended station blackout, attention was brought to the importance of the spent fuel pools' (SFPs) behavior in case of a prolonged loss of the cooling system. Since then, many analytical works have been performed to estimate the timing of hypothetical fuel uncovery for various SFP types. Experimentally, however, little was done to investigate issues related to the formation of a flammable gas mixture, distribution, and stratification in the SFP building itself and to some extent assess the capability for the code to correctly predict it. This paper presents the main outcomes of the Experiments on Spent Fuel Pool (ESFP) project carried out under the auspices of Swissnuclear (Framework 2012-2013) in the PANDA facility at the Paul Scherrer Institut in Switzerland. It consists of an experimental investigation focused on hydrogen concentration build-up into a SFP building during a predefined scaled scenario for different venting positions. Tests follow a two-phase scenario. Initially steam is released to mimic the boiling of the pool followed by a helium/steam mixture release to simulate the deterioration of the oxidizing spent fuel. Results shows that while the SFP building would mainly be inerted by the presence of a high concentration of steam, the volume located below the level of the pool in adjacent rooms would maintain a high air content. The interface of the two-gas mixture presents the highest risk of flammability. Additionally, it was observed that the gas mixture could become stagnant leading locally to high hydrogen concentration while steam condenses. Overall, the experiments provide relevant information for the potentially hazardous gas distribution formed in the SFP building and hints on accident management and on eventual retrofitting measures to be implemented in the SFP building.