• Food Engineering Progress
• /
• v.15 no.4
• /
• pp.404-412
• /
• 2011

The purpose of this study is to prepare extruded rice flours suitable for baking rice cookies. The extruded rice flours were prepared at 100 and 130$^{\circ}C$ temperature and 25 and 27% moisture content in a co-rotating twin screw extruder. The rice extrudates were dried at 100$^{\circ}C$ for 18 hr and subsequently ground into the fine flour. Characteristics of the extruded rice flours were examined by rapid visco analysis, hydration property analysis, differential scanning calorimetry (DSC), and in vitro digestion test. Water absorption, solubility, and swelling power of all extruded rice flours were higher than those of native rice flour. DSC analysis showed that native rice flour had a peak at about 65$^{\circ}C$ while all extruded rice flours did not show any peaks since they were already gelatinized during the extrusion proess. Viscosity of the extruded rice flours decreased with increasing temperature and lowering moisture content in the extrusion proess. The extruded rice flours prepared at 130$^{\circ}C$ exhibited lower viscosity than those prepared at 100$^{\circ}C$. The operating temperature of the extrusion proess was critical for the starch digestion in vitro. The extruded rice flours prepared at 130$^{\circ}C$ showed a rapid decrease in digestible starch content while an increased level of slowly digestible starch content was observed compared to those treated at 100$^{\circ}C$ in the extruder. Cookies were prepared with a mixture of wheat flour and extruded rice flours at the ratio of 7 to 3. The cookies made with the extruded rice flours had lower spread factor and darker yellow color than those prepared with wheat flour only. Hardness of the extruded rice flour-added cookies was similar to that of the wheat flour cookie whereas their overall acceptance was better. Therefore the rice cookies partially supplemented with extruded rice flours may have a potential as early childhood foods which require soft texture and allergy reduction.

• Clean Technology
• /
• v.25 no.1
• /
• pp.81-90
• /
• 2019

A dielectric barrier discharge (DBD) plasma reactor packed with $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst was used for the dry ($CO_2$) reforming of propane (DRP) to improve the production of syngas (a mixture of $H_2$ and CO) and the catalyst stability. The plasma-catalytic DRP was carried out with either thermally or plasma-reduced $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst at a $C_3H_8/CO_2$ ratio of 1/3 and a total feed gas flow rate of $300mL\;min^{-1}$. The catalytic activities associated with the DRP were evaluated in the range of $500{\sim}600^{\circ}C$. Following the calcination in ambient air, the ${\gamma}-Al_2O_3$ impregnated with the precursor solution ($Ni(NO_3)_2$ and $Ce(NO_3)_2$) was subjected to reduction in an $H_2/Ar$ atmosphere to prepare $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst. The characteristics of the catalysts were examined using X-ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectrometry (EDS), temperature programmed reduction ($H_2-TPR$), temperature programmed desorption ($H_2-TPD$, $CO_2-TPD$), temperature programmed oxidation (TPO), and Raman spectroscopy. The investigation revealed that the plasma-reduced $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst exhibited superior catalytic activity for the production of syngas, compared to the thermally reduced catalyst. Besides, the plasma-reduced $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst was found to show long-term catalytic stability with respect to coke resistance that is main concern regarding the DRP process.

• Journal of Plant Biotechnology
• /
• v.46 no.2
• /
• pp.127-135
• /
• 2019

The purpose of this study was to investigate suitable parts for callus induction and optimal concentrations of growth regulators, contained in the medium affecting shoot and rooting for in vitro mass production of Haworthia truncata. Leaves and flower bud showed 100% callus formation rate at NAA $1{\sim}2mgL^{-1}$ treatment, and NAA $1mgL^{-1}$ + TDZ $2mgL^{-1}$ treatment. The flower stalk showed 75% callus formation rate, at NAA $2mgL^{-1}$ + TDZ $2mgL^{-1}$ treatment in H. truncata. While the rate of callus formation was high in leaves and flower bud, leaves were the most efficient in obtaining most culture parts. Shoot induction rate from callus was highest, at NAA $0.1mgL^{-1}$ treatment in H. truncata. Additionally, the number of shoots formation was 66.3 shoots high, in NAA $1mgL^{-1}$ + BA $0.1mgL^{-1}$ treatment in H. truncata. In the case of acclimatization of regenerated plant, growth characteristics did not show significant difference (95%) shading with respect to the different ratio of substrate mixture, and it was determined that would be appropriate, considering plant height and appearance preference of H. truncata. It was established that optimization of culture condition, was responsible for mass propagation in vitro cultures of H. truncata.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.3
• /
• pp.49-61
• /
• 2019

Swine manure has been recognized as a organic sources for composting and many research was conducted to efficiently utilize and treat. This study was to evaluate a feasibility for producing swine manure compost under various treatment with mixture of swine manure and saw dust. Treatments were designed as follows; non aerated composting pile(REF), aerated composting pile of $100L/m^3$(EXP1), and aerated composting pile of $150L/m^3$(EXP2). The total days of fermentation were 28 days and each samples were collected at every 7 days from starting of composting. Temperature sensors were installed under 30~40cm from the surface of composting pile. Inner temperature in composting piles of EXP1 and EXP2 was rapidly increased to $67{\sim}75^{\circ}C$ within 1~2 days. The elevated temperatures found during the thermophilic phase are essential for rapid degradation of organic materials. While swine manure composted, moisture content, total nitrogen, EC of EXP1, EXP2 in sample at 28 days were lower than those of REF. But, pH and organic matter of EXP1, EXP2 in sample at 28 days were higher than those of REF. After finishing fermentation experiment, maturity was evaluated with germination test. Calculated germination index(GI) at REF, EXP1 and EXP2 were 23.49, 68.50 and 51.81, respectively. The values of germination index were higher at EXP1 and EXP2 which is aerated composting piles than REF which is non aerated composting pile. According to the results, composting process by aerated static pile compost had significant effect on the reduction of required period for composting. Supplying adequate amount of air to compost swine manure will greatly reduce composting period.

• Journal of Plant Biotechnology
• /
• v.46 no.1
• /
• pp.22-31
• /
• 2019

The objective of this study was to investigate the suitable parts for callus induction and optimal concentrations of growth regulators contained in the medium affecting shooting and rooting Echeveria laui and Echeveria elegans for in vitro mass production. To determine the suitable plant parts for callus induction, the leaves were divided into upper, medium and bottom parts and cultured on MS medium at different concentrations with $0{\sim}2mgL^{-1}\;NAA$ and $0{\sim}4 mgL^{-1}BA$. The upper and middle parts of leaves both showed 100% callus formation rate with $NAA\;1\;mgL^{-1}$ and $BA\;1\;mgL^{-1}$ treatment in E. laui. The middle parts of leaves showed 83.3% callus formation rate at $NAA\;2\;mgL^{-1}$ and BA 4 mgL-1 treatment in E. elegans. The shoot induction rate from callus was highest at $NAA\;0.1\;mgL^{-1}$ and $BA\;3\;mgL^{-1}$ treatment in E. laui and $NAA\;0.3\;mgL^{-1}$ in E. elegans. In addition, the number of shoots formation was 10.4 shoots high in $NAA\;1\;mgL^{-1}$ and $BA\;1\;mgL^{-1}$ treatment in E. laui and 12.0 shoots in most effective $NAA\;1\;mgL^{-1}$ and $BA\;0.1\;mgL^{-1}$ treatment in E. elegans. In the case of acclimatization of regenerated plant, growth characteristics did not show any significant difference (35 ~ 55%) shading with respect to the different ratio of substrate mixture, and it was determined that would be appropriate considered plant height and appearance preference of E. laui and E. elegans. It was established that the optimization of culture condition was responsible for the mass propagation in vitro cultures of E. laui and E. elegans.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.4
• /
• pp.109-122
• /
• 2022

Currently, most of the pig manure generated from pig farms in Korea is in the form of a slurry with a moisture content of about 97%. Pig manure slurry is a mixture of pig manure and cleaning water in the pig house. In this study, changes in properties of pig manure liquid fertilizer according to whether air was supplied or not and with the passage of storage period were analyzed for 120 days. During the experimental period, the degree of maturity of the pig manure liquid fertilizer was higher in the experimental closed batch reactors supplied with air than in the same type reactors not supplied with air. As the liquid fertilizer storage period elapsed, there was a tendency that liquid fertilizer was converted to a state of complete maturity. In the batch reactor in which air was supplied, the moisture content of pig manure slurry, which had a moisture content of 97.90%, was reduced to 96.82% at the end of the experiment. On the other hand, the moisture content in the reactor without air was reduced to 97.33%. The pH of the liquid fertilizer, which was 8.82 at the start of the experiment, changed to 7.57 in the reactor with air supplied and 8.75 in the reactor without air at the completion of the experiment. The nitrogen content in the liquid fertilizer was 0.198 mg/L on average at the start of the experiment and it was lowered to 0.076 mg/L in the air supplied reactor at the end of the experiment. On the other hand, the nitrogen content of the liquid fertilizer was lowered to 0.121 mg/L in the reactor to which air was not supplied. The phosphoric acid (P₂O₅) concentration in the liquid decreased higher in the liquid fertilizer filled in the reactor without air than the liquid fertilizer filled in the reactor with air supplied as the storage period elapsed. Considering the experimental results, it is considered that the quality of pig manure liquid fertilizer is improved when air is supplied to pig manure slurry and the storage period of pig manure slurry is longer.

• Korean Journal of Environmental Biology
• /
• v.39 no.4
• /
• pp.559-572
• /
• 2021

A survey was conducted to analyze water masses and spatial distributions of phytoplankton communities at 15 stations on the surface and chlorophyll a maximum layers (CML) in the western South Sea of Korea from September 8 to 9, 2021. As a result, water masses were classified into Coastal Waters (CW) with relatively low salinity, the Tsushima Warm Current (TWC) with high water temperature and high salinity, and mixed waters (MW) showing a mixture of these two water masses. Turbidity showed high concentration in both the surface and CML. The chlorophyll a concentration was as low as 0.90±0.43 ㎍ L^-1 in the surface, more than 1.1 ㎍ L^-1 in CW, around 1.0 ㎍ L^-1 in MW, and less than 0.5 ㎍ L^-1 in the TWC. CML was 1.64±0.54 ㎍ L^-1. Regarding species composition of phytoplankton communities, there were 57 species in 31 genera(diatoms, 57.8%; dinoflagellates, 35.1%; and other phytoflagellates, 7.1%). The phytoplankton standing crop had 4.6±7.6 cells mL^-1 in the surface, more than 30 cells mL^-1 in the CW, 2-5 cells mL^-1 in the MW, and less than 2 cells mL^-1 in the TWC. CML was slightly higher than the surface with a variation of 5.7±8.4 cells mL^-1. Dominant species were found to be Rhizosolenia flagilissima f. flagilissima, Skeletonema costatum-ls, and Nitzschia sp./ small size in the surface. For the CML Rh. flagilisima f. flagilissima showed a dominance of 12.0%. For the surface, the diversity variation was 2.36±0.40, which was high for TWC but low for MW. For CML, the diversity variation was 2.29±0.52, which was slightly lower than that of the surface. The dominance in the surface was 0.50±0.15, with a fluctuation range of more than 0.5 in MW and less than 0.5 in the TWC, which was different from the diversity. According to correlation analysis and principal component analysis (PCA), the presence of phytoplankton standing crops was high in CW but low in MW and TWC. That is, phytoplankton communities in early autumn were strongly affected by the expansion and mixing of water masses in western South Sea.

• Economic and Environmental Geology
• /
• v.5 no.4
• /
• pp.187-209
• /
• 1972

Drilling position is one of the most important factors affecting on the blasting effects. There has been many reports on several blasting factors of burn-cut by Messrs. Brown and Cook, but in this study the author tried to compare drilling positions of burn-cut to pyramid-cut, and also to correlate burn-cut effects of drilling patterns, not being dealt by Prof. Ito in his theory, which emphasized on dynamical stress analysis between explosion and free face. According to former theories, there break out additional tensile stress reflected at the free face supplemented to primary compressive stress on the blasting with one-free-face. But with these experimented new drilling patterns of burn-cut, more free faces and nearer distance of each drilling holes make blasting effects greater than any other methods. To promote the above explosive effect rationary, it has to be considered two important categories under-mentioned. First, unloaded hole in the key holes should be drilled in wider diameter possibly so that it breaks out greater stress relief. Second, key holes possibly should have closer distances each other to result clean blasting. These two important factors derived from experiments with, theories of that the larger the dia of the unloaded hole, it can be allowed wider secondary free faces and closes distances of each holes make more developed stress relief, between loaded and unloaded holes. It was suggested that most ideal distance between holes is about 4 clearance in U. S. A., but the author, according to the experiments, it results that the less distance allow, the more effective blasting with increased broken rock volume and longer drifted length can be accomplished. Developed large hole burn-cut method aimed to increase drifting length technically under the above considerations, and progressive success resulted to achieve maximum 7 blasting cycles per day with 3.1m drifting length per cycle. This achievement originated high-speed-drifting works, and it was also proven that application of Metallic AN-FO on large hole burn-cut method overcomes resistance of one-free-face. AN-FO which was favored with low price and safety handling is the mixture of the fertilizer or industrial Ammonium-Nitrate and fuel oil, and it is also experienced that it shows insensible property before the initiation, but once it is initiated by the booster, it has equal explosive power of Ammonium Nitrate Explosives (ANE). There was many reports about AN-FO. On AN-FO mixing ratio, according to these experiments, prowdered AN-FO, 93.5 : 6.5 and prilled AN-FO 94 : 6, are the best ratios. Detonation, shock, and friction sensities are all more insensitive than any other explosives. Residual gas is not toxic, too. On initation and propagation of the detonation test, prilled AN-FO is more effective than powered AN-FO. AN-FO has the best explosion power at 7 days elapsed after it has mixed. While AN-FO was used at open pit in past years prior to other conditions, the author developed new improved explosives, Metallic AN-FO and Underwater explosive, based on the experiments of these fundmental characteristics by study on its usage utilizing AN-FO. Metallic AN-FO is the mixture of AN-FO and Al, Fe-Si powder, and Underwater explosive is made from usual explosive and AN-FO. The explanations about them are described in the other paper. In this study, it is confirmed that the blasting effects of utilizing AN-FO explosives are very good.

• Korean Journal of Agricultural Science
• /
• v.11 no.1
• /
• pp.146-159
• /
• 1984

This study was the contrast of the compressive strength, the tensile strength, the reducing ratio and the flow of mortar using dispersing agent and high fluid admix. 1. The admix ratio of chemical admixtures espressing maximum strength appeared the same result high fluid admix SP was 0.6%, the dispersing agents LG and C211 were 0.2%, SK was 0.3%, C376 was 0.5%. But two or three times more than standard quantity made the strength's fast lowness, which influenced bad to wateriness and retard the soli-dification. 2. When proper quantity of chemical admixture was used, the increment of compressive strength was as follows. High fluid admix SP was 40.7% and the average increasing rate of dispersing agents(C211 was 19.5%, LG was 19.1%, C376 was 17.9%) was 18.7% more than normal mortar in the codition of 7 days. Also, in the condition of 28 days, high fluid admix SP was about 24.4% and the average of dispersing agents(LG was 21.1%, C211 was 16.4%, SK was 11.1%, C376 was 7.6%) was 14.1%. 3. When proper quantity of chemical admixture was used, the increment of tensile strength was as follows. High fluid admixture SP was 26.6% and the average increasing agents(SK was 16.0%, C376 was 14.7%, LG was 10%, C211 was 5.8%) was 11.6%. Also, in the condition of 28 days, high fluid admix SP was 16.5% and the average increasing rate of dispersing agents(LG was 19.1%, SK was 10.6%, C211 was 10.1%, C376 was 8.7%) was 12.1%. 4. As for the reducing ratio of each dispersing agent, he flow of mortar was less than the slump of concrete. That is; the reducing ratio of concrete was 15% adding each dispersing agent, but the reducing ratio of mortar was in the range of from 5.8% to 13.5% in 1 : 1 mixture, from 7.6% to 14.2% in 1 : 2, from 9.5% to 18.8% in 1 : 3. 5. The fluidity of each chemical admixture was as follows. High fluid admix SP in the condition of 1: 1 and 1 : 2 showed the best result than other dispersing agent and 1 : 3 showed the same result like other agents. Therefore these good dispersing agents were suitable in the prepact concrete construction using intrusion mortar.

• Journal of Nutrition and Health
• /
• v.8 no.1
• /
• pp.15-37
• /
• 1975

I. Subject of the study A study on the nutritive value and utilization of powdered seaweeds. II. Purpose and Importance of the study A. In Korea the shortage of food will be inevitable by the rapidly growing population. It will be very important study to develop a new food from the seaweeds which were not used hitherto for human consumption. B. The several kinds of seaweeds have been used by man in Korea mainly as side-dishes. However, a properly powdered seaweed will enable itself to be a good supplement or mixture to certain cereal flours. C. By adding the powdered seaweed to any cereals which have long been staple foods in this country the two fold benefits; saving of cereals and change of dietary pattern, will be secured. III. Objects and scope of the study A. Objects of the study The objects will come under four items. 1. To develop a powdered seaweed as a new food from the seaweeds which have been not used for human consumption. 2. To evaluate the nutritional quality of the products the analysis for chemical composition and animal feeding experiment will be conducted. 3. Experimental cocking and accepability test will be conducted for the powdered products to evaluate the value as food stuff. 4. Sanitary test and also economical analysis will be conducted for the powdered products. B. Scope of the study 1. Production of seaweed powders Sargassum fulvellum growing in eastern coast and Sargassum patens C.A. in southern coast were used as the material for the powders. These algae, which have been not used for human consumption, were pulverized through the processes of washing, drying, pulverization, etc. 2. Nutritional experiments a. Chemical composition Proximate components (water, protein, fat, cellulose, sugar, ash, salt), minerals (calcium, phosphorus, iron, iodine), vitamins (A, $B_1,\;B_2$ niacin, C) and amino acids were analyzed for the seaweed powders. b. Animal feeding experiment Weaning 160 rats (80 male and 80 female rats) were used as experimental animals, dividing them into 16 groups, 10 rats each group. Each group was fed for 12 weeks on cereal diet (Wheat flour, rice powder, barley powder, potato powder, corn flour) with the supplementary levels of 5%, 10%, 15%, 20% and 30% of the seaweed powder. After the feeding the growth, feed efficiency ratio, protain efficiency ratio and ,organs weights were checked and urine analysis, feces analysis and serum analysis were also conducted. 3. Experimental cooking and acceptability test a. Several basic studies were conducted to find the characteristics of the seaweed powder. b. 17 kinds of Korean dishes and 9 kinds of foreign dishes were prepared with cereal flours (wheat, rice, barley, potato, corn) with the supplementary levels of 5%, 10%, 15%, 20% and 30% of the seaweed powder. c. Acceptability test for the dishes was conducted according to plank's Form. 4. Sanitary test The heavy metals (Cd, Pb, As, Hg) in the seaweed powders were determined. 5. Economical analysis The retail price of the seaweed powder was compared with those of other cereals in the market. And also economical analysis was made from the nutritional point of view, calculating the body weight gained in grams per unit price of each feeding diet. IV. Results of the study and the suggestion for application A. Chemical composition 1. There is no any big difference in proximate components between powders of Sargassum fulvellum in eastern coast and Sargassum patens C.A. in southern coast. Seasonal difference is also not significant. Higher levels of protein, cellulose, ash and salt were found in the powders compared with common cereal foods. 2. The levels of calcium (Ca) and iron (Fe) in the powders were significantly higher than common cereal foods and also rich in iodine (I). Existence of vitamin A and vitamin C in the Powders is different point from cereal foods. Vitamin $B_1\;and\;B_2$ are also relatively rich in the powders.'Vitamin A in ·Sargassum fulvellum is high and the levels of some minerals and vitamins are seemed4 to be some influenced by seasons. 3. In the amino acid composition methionine, isoleucine, Iysine and valine are limiting amino acids. The protein qualities of Sargassum fulvellum and Sargassum patens C.A. are seemed to be .almost same and generally ·good. Seasonal difference in amino acid composition was found. B. Animal feeding experiment 1. The best growth was found at.10% supplemental level of the seaweed Powder and lower growth rate was shown at 30% level. 2. It was shown that 15% supplemental level of the Seaweed powder seems to fulfil, to some extent the mineral requirement of the animals. 3. No any changes were found in organs development except that, in kidney, there found decreasing in weight by increasing the supplemental level of the seaweed powder. 4. There is no any significant changes in nitrogen retention, serum cholesterol, serum calcium and urinary calcium in each supplemental level of the seaweed powder. 5. In animal feeding experiment it was concluded that $5%{\sim}15%$ levels supplementation of the seaweed powder are possible. C. Experimental cooking and acceptability test 1. The seaweed powder showed to be utilized more excellently in foreign cookings than in Korean cookings. Higher supplemental level of seaweed was passible in foreign cookings. 2. Hae-Jo-Kang and Jeon-Byung were more excellent than Song-Pyun, wheat cake, Soo-Je-Bee and wheat noodle. Hae-Je-Kang was excellent in its quality even as high as 5% supplemental level. 3. The higher levels of supplementation were used the more sticky cooking products were obtained. Song-Pyun and wheat cake were palatable and lustrous in 2% supplementation level. 4. In drop cookie the higher levels of supplementation, the more crisp product was obtained, compared with other cookies. 5. Corn cake, thin rice gruel, rice gruel and potato Jeon-Byung were more excellent in their quality than potato Man-Doo and potato noodle. Corn cake, thin rice gruel and rice gruel were excellent even as high as 5% supplementation level. 6. In several cooking Porducts some seaweed-oder was perceived in case of 3% or more levels of supplementation. This may be much diminished by the use of proper condiments. D. Sanitary test It seems that there is no any heavy metals (Cd, Pb, As, Hg) problem in these seaweed Powders in case these Powders are used as supplements to any cereal flours E. Economical analysis The price of the seaweed powder is lower than those of other cereals and that may be more lowered when mass production of the seaweed powder is made in future. The supplement of the seaweed powder to any cereals is also economical with the criterion of animal growth rate. F. It is recommended that these seaweed powders should be developed and used as supplement to any cereal flours or used as other food material. By doing so, both saving of cereals and improvement of individual's nutrition will greatly be achieved. It is also recommended that the feeding experiment for men would be conducted in future.