• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.93-98
• /
• 2005

The purpose of this study was to analyze the compression strength research by aerated concrete as mixing ratio This Study used foaming-agent and produced aerated concrete by pre-foam way that is used in construction site. An experiment changes unit cement amount, w/c and the glass fiber mixing rate and 'measured capacity change, unit capacity weight and compressive strength. The results obtained from experimental study are as following; Research to reduce unit capacity weight in condition more than unit cement amount 500kgf is considered should be gone side by side. The highest compressive strength result appeared in aerated concrete that cement amount 600kgf and w/c ratio $45\%$, $50\%$. compressive strength was increased maximum $34%$ when glass fiber $0.7\%$ addition cause by coherence enlargement to enlargement of cement paste and glass fiber addition per unit volume

• Journal of Powder Materials
• /
• v.10 no.2
• /
• pp.89-96
• /
• 2003

The recent trend of miniaturization and high performance of vehicle engines has put an urgent necessity for the development of valve seats which can operate under more severe conditions. In order to develope valve seat material that has the most excellent wear resistance at operating temperature of engine through improvement of the progress of work. the effects of mixing ratio of the milled powder on sintered and Cu-infiltrated properties of sintered valve seats have been studied. The resultant radial crushing strength and hardness of sintered specimens were gradually increased with increasement of volume of milled powders. It is because increasement of sintering density by increasing of surface diffusion. The hardness of Cu-infiltrated specimens became lower than that of the commercial powders as the increasement of volume of milled powders. It was due to the decrease of the amount of the martensite. By results of this research, It has been found that martensite is formed around of the Cu-infiltrated site and the decrease of the amount of the martensite is due to decrease of the amount of the Cu-infiltrated site by the decrease of gas channel.

• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.4
• /
• pp.559-571
• /
• 2006

The overall objective of this research was to find out the interrelation of coagulant and organic matter during rapid mixing process and to identify the change of organic matter by mixing condition and to evaluate the effect of coagulation pH. During the coagulation, substantial changes in dissolved organics must be occurred by coagulation due to the simultaneous formation of microflocs and NOM precipitates. Increase in the organic removal efficiency should be mainly caused by the removal of microflocs formed during coagulant injection. That is, during the mixing period, substantial amount of dissolved organics were transformed into microflocs due to the simultaneous formation of microflocs and NOM precipitates. The results also showed that 40 to 80% of dissolved organic matter was converted into particulate material after rapid mixing process of coagulation. During the rapid mixing period, for purewater, formation of dissolved Al(III) (monomer and polymer) constant by rapid mixing condition, but for raw water, the species of Al hydrolysis showed different result. During the rapid mixing period, for high coagulant dose, Al-ferron reaction increases rapidly. At A/D(Adsorption and Destabilization) and sweep condition, both $Al(OH)_3(s)$ and dissolved Al(III) (monomer and polymer) exist, concurrent reactions by both mechanism appear to cause simultaneous precipitation.

• Journal of the Korean Vacuum Society
• /
• v.3 no.3
• /
• pp.316-321
• /
• 1994

Rate of mixing of Cu particles to polyimide substrate at interfaces under different thermal treatments was analyzed by Rutherford Backscattering spectroscopy using 2.0 MeV He+ ions. T he mixing rate was a function of annealing temperature and time and was constant at afioxed temperature. The amount of mixing increased linearly with time and the mixing rate increased with temperature. The activation energy for interface mixing between Cu and polyimide was 2.6 kcal/mol. The X-ray studies showed the Cu(111) plane peak changed with annealing time at fixed temperature. The mixing of Cu to polyimide was explained with segmental motion of PI chain and with interaction between functional group of the chain and metal electron donor. The comparisons were made bewteen the mixing induced by ion irradiation and by thermal treatment. The various factors affecting the interface mixing are discussed.

• Corrosion Science and Technology
• /
• v.3 no.6
• /
• pp.257-261
• /
• 2004

Leaking of fuel gas in a building creates flammable atmosphere and gives rise to explosion. Observations from accidents suggest that some explosions are caused by quantity of gas significantly less than the lower explosion limit amount required to fill the whole confined space, which might be attributed to inhomogeneous mixing of the leaked gas. The minimum amount of leaked gas for explosion is highly dependent on the degree of mixing in the building. This paper proposes a method for estimating minimum amount of flammable gas for explosion assuming Gaussian distribution of flammable gas.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.6
• /
• pp.584-588
• /
• 1997

A new device to accurately deliver small amount of modifier into supercritical carbon dioxide fluid is described. Carbon dioxide, the most widely used mobile phase in supercritical fluid chromatography, is a relatively non-polar fluid, and hence the addition of small amount of polar modifiers could be necessary to migrate polar solutes. In this work, supercritical CO₂and modifier are delivered from the pump to a 100 μL mixing chamber in which a small magnetic bar is rotating. After passing through the mixing chamber, supercritical CO₂is changed to a new mobile phase with different polarity. The amount of modifier added into supercritical CO₂is measured by an amperometric microsensor, which is prepared from a thin film of perfluorosulfonate ionomer.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.3
• /
• pp.132-136
• /
• 2002

In this study, we analyzed the luminous efficiencies of Ne-Xe-Ar and He-Ne-Xe-Ar mixing gas in compared with those of Ne-Xe and He-Ne-Xe mixing gas to improve luminous efficiency by adding a small amount of Ar gas. At the Xe 4%, the brightness of Ne-Xe and He-Ne-Xe mixing gas is higher than others. As the Xe % increases, power consumption decreases. Thus, in the Ne-Xe and He-Ne-Xe mixing gas of Xe 4%, we obtained maxium luminous efficiency. The Ar concentration is varied from 0.1% to 0.7% in this study. The luminous efficiency of the Ne-Xe(4%) mixing gas is improved to 1.16 and 1.13 lm/W by adding an Ar concentration of 0.4% and 0.5%, respectively. The luminous efficiency of the He-Ne-Xe(4%) (He : Ne = 7 : 3) mixing gas is considerably improved by adding an Ar concentration of above 0.3%. The maximum luminous efficiency of this mixing gas is 1.38 lm/W at the condition of adding an Ar concentration of 0.5%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.38-43
• /
• 2011

A CNG/diesel dual-fuel engine uses CNG as the main fuel and injects a small amount of diesel as an ignition priming. This study proposed the modification of the existing diesel engine into a dual-fuel engine that injects diesel with a high pressure by common rail direct injection (CRDI) and by injecting CNG at the intake port for premixing. And experiment was progressed for understanding about effect of CNG mixing ratio. The CNG/diesel dual-fuel engine showed equally satisfactory coordinate torque and power regardless of CNG mixing ratio. The PM emission was low at any CNG mixing ratio because of very small diesel pilot injection. In case of NOx and HC, high CNG mixing ratio showed low NOx and HC emissions at low speed. At medium & high speed, low CNG mixing ratio showed low NOx and HC emissions. Therefore, it would be optimized by controlling CNG mixing ratio.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.19 no.1
• /
• pp.85-107
• /
• 1993

The cosmetic fine powders were mixed with variation of mixing time(5) in the mixers (ribbon mixer, powder mixer, micropulverizer and fine impact mill). The powders were nixed with small amount of ferric oxide. as tracer. The mixed powders ere measured the particle size distribution, specific surface area and surface color with mixing time (s). The color variation, particle size distribution and specific surface area of the mixed powder exist a relationship with mining time(s) that can be expressed as mathematical equations to show the degree of the mixing of the powder mixture. The linear velocity of the impellar tip is the main factor contributing to he mixing efficiency of the mixers un this study. According to the linear velocity, he mixers used are devieded as convection mixing (ribbon mixer), sclera mixing powder mixer) and diffusion mixing (micropulverizer/fine impact mill).

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.4
• /
• pp.60-67
• /
• 2018

As the lack of specific aggregation intensifies, the development of alternative resources is urgent. Construction waste is increasing every year, but recycled aggregate is used as a low value added material. Various studies are currently underway at the national level. In this paper, the mechanical performance of the concrete according to the concrete mixing method and the replacement amount of the circulating coarse aggregate was compared and evaluated. Concrete mixing method was normal mixing approach(NMA) method, two-stage mixing approach1 (TSMA1) method, two-stage mixing approach2 (TSMA2) method. Fresh concrete was tested for air content, slump test, and unit volume weight. Compressive strength and flexural strength were tested in hardened concrete. According to the TSMA method, the mechanical performance difference of concrete is shown, and the strength is decreased according to the circulating coarse aggregate replacement amount.