• 한국구조물진단유지관리공학회 논문집
• /
• 제9권3호
• /
• pp.87-92
• /
• 2005

콘크리트의 투수성은 콘크리트의 내구성에 크게 영향을 미치므로, 투수성의 합리적인 측정과 그 개선이 요구된다. 따라서 콘크리트의 투수성은 콘크리트 구조물이 건전한 상태를 유지하고 있는 초기 상태에서 평가하는 것 보다 실제 하중을 받고 있는 공용중인 상태에서 평가하는 것이 보다 합리적이라 할 수 있다. 본 연구에서는 콘크리트의 투수성능을 개선하기 위하여 섬유의 종류 및 혼입율, 수지 종류를 달리하여 콘크리트 시험체를 제작하였으며, 투수성의 합리적인 평가를 위해서 하중을 받아 균열발생 등 성능이 저하된 콘크리트 구조물의 실제 상태를 모사하기 위하여 시험체에 선행하중을 시험체 압축강도의 50%, 70% 작용시킨 후에 투수시험을 수행하여 그 결과를 비교분석 하였다. 시험결과 투수계수는 선행하중을 가하지 않은 경우보다 선행하중 50%일 때 대략 1.4배, 70%일 때 17.8배 증가되었고, 하이브리드 강섬유보강이 콘크리트의 투수성능 개선에 가장 효과적임을 알 수 있었다.

• 펄프종이기술
• /
• 제40권1호
• /
• pp.29-34
• /
• 2008

The charcoal has been used not only as fuel but also as human health care material since it was used. Charcoal's performances were generally investigated in aspects of energy efficiency and caloric values. This study was conducted in order to increase charcoal's application area and to develop functional paper. Five types of charcoal were used on a basis of gas absorption properties from previous study. Handsheets were made by two methods by internal loading and surface spray on interlayer. Strength properties of internal loading and interlayer spray handsheets were decreased as the charcoal loading increased. Ethylene gas absorption property was higher in both of oak's black charcoal and white charcoal than others. In terms of strength, 5-10% charcoal loading was efficient. Above 10% loading, a rate of strength decrease was higher than that of ethylene gas absorption rate. Formaldehyde absorption property was higher at both of oak's black charcoal and mixed charcoal than others. However, to guarantee enough charcoal loading should be higher than 95 $g/m^2$ for sufficient formaldehyde absorption.

• 한국산업보건학회지
• /
• 제7권1호
• /
• pp.3-18
• /
• 1997

This study was conducted to evaluate desorption efficiencies by types of desorption solvent for polar and non-polar organic compounds collected on activated charcoal tubes. Analytes tested were toluene, m-xylene, isobutyl alcohol, n-butyl alcohol, cellosolve acetate, and butyl cellosolve. Three different concentration levels of spiked sample were made. Types of cosolvent mixed with the main solvent, $CS_2$, were methanol, pentanol, and dimethylformamide (DMF) and the cosolvent for methylenechloride was methanol. The amounts of cosolvent added to the main solvent were 1, 5, and 10% by volume (v/v%), respectively. The results were as follows: 1. For all mixed solvents except 1% methanol and 1% pentanol with $CS_2$, desorption efficiency significantly increased, compared with that of $CS_2$ alone. 2. Desorption efficiency increased by increasing analyte loading on charcoal tube regardless of mixed solvents used and the material polarity. 3. For all cosolvents mixed with $CS_2$ by 1% and 5% volume, desorption efficiency for non-polar compound was significantly higher than that of polar compound. For the 10% mixed solvents and the methylenechloride mixed with methanol, the results were opposite. 4. The lowest mean percent bias of 4.79% was obtained from the 5% DMF-$CS_2$ mixed solvent, followed by 4.82% from the 10% DMF-$CS_2$ solvent while the highest bias of 23.26% was from the solvent of $CS_2$ alone. Based on the results of this study, in order to increase desorption efficiency, it is recommended to add such cosolvents as methanol, pentanol, and DMF to $CS_2$, preferably 5% by volume for analyzing polar compounds collected in charcoal tubes.

• 한국안전학회지
• /
• 제20권2호
• /
• pp.79-83
• /
• 2005

Recently, column-supported wall structural system is frequently adopted in mixed-use high-rise buildings. Due to the sudden change of stiffness at the transfer floor proper load transfer and avoiding stress concentration are very important in column-supported wall structural system. It is revealed by many investigators that 2-dimensional analysis is not reliable and inappropriate selection of element for modeling may lead to erroneous result for gravitational loading. In this study, structural behavior of column-supported wall structure at transfer floor subject to lateral loading is compared by changing modeling methods.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.812-815
• /
• 2007

Computational simulation has been performed to design the filtration system for Korea model IGCC demonstration plant. The filtration system for optimal design has four effective filters corresponding to the clusters composed of a group of ceramic candle filters. It was analyzed how the different entrance geometry influences the flow field and the particle behavior in the filtration system. The particle loading is minimum when the gas mixed with particles flows into the filter vessel with a shroud tube through a tangential inlet. However, the particle loading is maximum when the gas with particles enters the filter vessel through a normal inlet which a entrance tube extended from. By controling adequately both conditions of inflow, the filtration system can be operated optimally to prolong the filter life-time and to save the energy for cleaning filters.

• Structural Engineering and Mechanics
• /
• 제34권3호
• /
• pp.377-390
• /
• 2010

This paper studies fracture initiation direction of two parallel non-coplanar cracks of equal length. Using the dislocation pile-up modelling, singular integral equations for two parallel cracks subjected to mixed-mode loading are derived and the crack-tip field including singular and non-singular terms is obtained. The kinking angle is determined by using the maximum hoop stress criterion, or the ${\sigma}_{\theta}$-criterion. Results are presented for simple uniaxial tension and biaxial loading. The biaxiality ratio has a noticeable influence on crack growth direction. For the case of biaxial tension, when neglecting the T-stress the crack branching angle is overestimated for small crack inclination angles relative to the largest applied principal stress direction, and underestimated for large crack inclination angles.

• Journal of Mechanical Science and Technology
• /
• 제16권5호
• /
• pp.655-665
• /
• 2002

Two-dimensional elastic analysis of doubly periodic circular holes in an infinite plane is given in this paper. Two cases of loading, remote tension and remote shear, are considered. A rectangular cell is cut from the infinite plane. In both cases, the boundary value problem can be reduced to a complex mixed one. It is found that the eigenfunction expansion variational method is efficient to solve the problem. Based on the deformation response under certain loading, the notched medium could be modeled by an orthotropic medium without holes. Elastic properties for the equivalent orthotropic medium are investigated, and the stress concentration along the hole contour is studied. Finally, numerical examples and results are given.

• Management Science and Financial Engineering
• /
• 제5권1호
• /
• pp.1-25
• /
• 1999

There is a worldwide trend to automate the handling operations in port container terminals in an effort to improve productivity and reduce labor cost. This study iscusses how to apply an AGV(automated guided vehicle) system to the handling of containers in the yard of a port container ter-minal. The main issue of this paper is how to assign tasks of container delivery to AGVs during ship operations in an automated port container terminal. A dual-cycle operation is assumed in which the loading and the discharging operation can be performed alternately. Mixed integer linear program-ming formulations are suggested for the dispatching problem. The completion time of all the dis-charging and loading operations by a quayside crane is minimized, and the minimization of the total travel time of AGVs is also considered as a secondary objective. A heuristic method using useful properties of the dispatching problem is suggested to reduce the computational time. The perfor-mance of the heuristic algorithm is evaluated in light of solution quality and computation time.

• 한국농공학회지
• /
• 제42권5호
• /
• pp.103-113
• /
• 2000

A decision support system DSS-WQMRA (Decision Support System-Water Quality Management in Rural Area) was developed to help regional planners for the water quality management in a rural basin. The integrated model DSS-WQMRA, written in JAVA, includes four subsystems such as a GIS, a database, water quality simulation models and a decision model. In the system, the GIS deals with landuse and the location of pollutant sources. The database manages each data and supplies input data for various water quality simulation models. the water quality simulation model is composed of the GWLF( Generalized Watershed Loading Function), PCLM(Pollutant Loading Calculation Module) and the WASP5 model. The decision model based on mixed integer programming is designed to determine optimal costs and thus allow the selection of managemental practices to meet the water quality criteria. The methodology was tested with an example application in the Bokha River Basin, Kyunggi Province in Korea. It was proved that the integrated model DSS-WQMRA could be very useful for water quality management including the non-point source pollution in rural areas.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.350-357
• /
• 2002

The scale effect should be considered to determine the bearing capacity and settlement of footings from Plate-Load Test, because of the size difference between a footing and a loading plate. To analyze characteristics of bearing capacity and settlement according to the difference of loading plate sizes, model tests were peformed with four different sizes of square plate, which is B=10, 15, 20 and 25cm respectively, on five different kinds of subsoil, which is pure sand(100:0), sand-clay mixed soil(75:25, 50:50, 25:75), and pure clay(0:100). Based on the analyzed results, this paper also proposed a method of bearing capacity and settlement determination, where scale effect is considered depending on the mixing ratio of sand and clay. Applying the formular proposed in this research to field problems, it is expected that evaluation of bearing capacity and settlement of footings can be more reliable and more economic construction can be achieved.