• Geophysics and Geophysical Exploration
• /
• v.12 no.2
• /
• pp.215-220
• /
• 2009

Cement based mortars are widely used to improve the soft ground of a dam site, highway construction, and karst voids. The mechanical properties of the mortar are well documented in literature, however very limited work is done on their physical properties such as electrical resistivity which is considered as one of the most important physical property known while improving the soft grounds. In this paper, electrical resistivity of the Portland cement mortars is examined by employing the Wenner technique. Cylindrical specimens with various water/cement ratios (w/c) ranges from 0.35, 0.45, 0.50 and 0.65 were cast and tested. The test results showed that the electrical resistivity of the mortar increases with increasing curing time and decreases with increasing water content and w/c. A reasonable, good relation was found between electrical resistivity and compressive strength of mortar.

• Journal of Soil and Groundwater Environment
• /
• v.27 no.1
• /
• pp.17-24
• /
• 2022

This work examined the effect of mixing transition metal-based additives [FeCl₃, Fe-containing paper mill sludge (PMS), CoCl₂·H₂O, ZrO₂, and α-Fe₂O₃] on the thermochemical conversion of coffee waste (CW) in carbon dioxide-assisted pyrolysis process. Compared to the generation amounts of syngas (0.7 mole% H₂ & 3.0 mole% CO) at 700℃ from single pyrolysis of CW, co-pyrolysis in the presence of Fe- or Zr-based additives resulted in the enhanced production of syngas, with the measured concentrations of H₂ and CO ranging 1.1-3.4 mole% and 4.6-13.2 mole% at the same temperature, respectively. In addition, α-Fe₂O₃ biochar possessed the adsorption capacity of As(V) (19.3 mg g^-1) comparable to that of ZrO₂-biochar (21.2 mg g^-1). In conclusion, solid-type Fe-based additive can be highly considered as an efficient catalyst to simultaneously produce syngas (H₂ & CO) as fuel energy resource and metal-biochar as sorbent.

• Journal of the Korea Furniture Society
• /
• v.20 no.6
• /
• pp.605-611
• /
• 2009

This paper reports the application of radiocarbon wiggle matching for Korean wooden artifacts such as furniture and Buddhist statues for precise dating. Ten biannual samples of 20 years (AD 1249-1268) for AMS (accelerator mass spectrometry) radiocarbon measurements were prepared from a board of the pedestal for Buddhist statue at Jeongsusa (temple) in Kangwhado, Korea, which was dendrochronologically dated. The average 95.4% confidence interval of radiocarbon dating without wiggle matching was 123 year. When wiggle matching technique was applied, it became 37 year, 3.3 times smaller than that without wiggle matching. The results indicated that wiggle matching technique using the calibration curve for northern hemisphere (IntCal04: International radiocarbon calibration curve announced in 2004) can produce precise dates for Korean wooden artifacts which possess as much as 20 tree rings.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.10
• /
• pp.1832-1838
• /
• 2010

Aging of transformer insulating material in natural ester insulating oil is compared to that in conventional transformer oil. Aging of insulating paper and insulating oil have been studied by performing accelerated thermal aging test. Sealed aging test vessels containing cooper, laminated core, Kraft paper and insulating oil(natural oil or mineral oil) were aged at $140^{\circ}C$ for 500, 1000, 1500 and 2000 hours. Insulating oils after aging are investigated with total acid number, breakdown voltage and viscosity. Also, degradation of insulating paper after aging is determined using breakdown voltage and mechanical strength. Accelerated aging studies demonstrate a slower aging rate for natural ester insulating oil compared to the rate for conventional mineral oil.

• Environmental and Resource Economics Review
• /
• v.15 no.4
• /
• pp.713-740
• /
• 2006

In this paper, we examine what factors should be considered in cost-benefit analysis of a resource-developing project as cos and benefit item. According to this study, the reduction in forest product value and the reduction in function to clean air pollution should be included as a environmental cost. However, the reduction in recreation function and function in cleaning water need not to be included. We also calculated a cost-benefit of developing project for lime mineral of A company by applying these factor just mentioned. This paper concluded that the net benefit of this project is positive and the range of the value is from 689,900million won to 1,784,000million won.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.505-508
• /
• 2004

This paper investigated the setting and compressive strength of concrete with the combination of mineral and chemical admixture. According to test results, plain concrete with high early strength development type AE water reducing agent(HEAEWRA) and $10\%$ of CKD respectively had earlier setting time than concrete with AE water reducing agent by $0.5\~1.5$ hours. Setting time of concrete with retarding type AE water reducing agent(RAEWRA) and FA $30\%$, BS $60\%$ respectively retarded by as much as $4\~7.5$ hours compared with plain concrete. Plain concrete with HEA WRA, $10\%$ of CKD and RAEWRA had higher strength than that of AE water reducing agent by as much as 5MPa at 28days. From the result of the paper, it is found that the combination of mineral admixture and setting accelerating or retarding agent can reduce the hydration heat cracks by setting time difference and hydration heat reduction effects.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.351-352
• /
• 2002

In this paper, studies were made on the palm oil methyl ester (POME) added lubricants using FT-IR for monitoring oil degradation. In order to assess the degradation characteristics of POME added lubricant by FT-IR, static oxidation test was conducted using three different blended lubricants (viz, zero percent POME, five percent POME and ten percent POME with mineral-based oil) for 280 hrs. The oxidation temperature was set at $140^{\circ}C$. FT-IR quantitative data indicate an increased in oxidation products which was formed from 10% POME added lubricants after 280 hrs of oxidation test. The 5% POME added lubricant and mineral-based lubricant (without POME) showed less oxidation product after the test. From the FT-IR spectrum analysis of the oxidized oils it could be concluded that 5% POME can improve the performance of mineral-based oil by forming protective films.

• Economic and Environmental Geology
• /
• v.23 no.3
• /
• pp.353-358
• /
• 1990

This paper presents numerical experiments on migration of synthetic seismograms using by $45^{\circ}$ wave equation. The seismograms used are zero-offset seismogram (corresponding to stacked section) on point reflectors, dipping plane reflector, faulted and folded layers. The seismograms are constructed by upward continuation of seismic source wavelets, exploading on subsurface reflection interfaces, to the earth surface. The synthetic seismograms are migrated by downward continuation and imaging. The upward and downward continuations are implemented by solving the $45^{\circ}$ wave equation with the finite-difference method. Migration of the synthetic data used in this study results in relatively accurate reposition of subsurface structures while the synthetic sections are quite different from the structures.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2007.07a
• /
• pp.129-137
• /
• 2007

This paper presents a numerical model which can predict degree of hydration of cement mineral component, such as $C_{3}S$, $C_{2}S$, $C_{3}A$, $C_{4}AF$ and microstructure of hydrating cement as a function of water to cement ratio, cement particle size distribution, cement mineral components and temperature. In this model cement particles are parked randomly in cell space and hydration process is described using a multi-component integrated kinetic model. The simulation result of degree of hydration of cement mineral component agrees well with experiment result. The content of cement hydration product, such as CSH and CH can be obtained as an accompanied result during hydration process. By introducing of equal-area projection method, water withdrawl mechanism and contact area among cement particles can be considered in detail. By using proposed method, pore size distribution of hydrating cement is predicted.

• Computers and Concrete
• /
• v.13 no.1
• /
• pp.97-115
• /
• 2014

Silica fume is a by-product of induction arc furnaces and has long been used as a mineral admixture to produce high-strength, high-performance concrete. Due to the pozzolanic reaction between calcium hydroxide and silica fume, compared with that of Portland cement, the hydration of concrete containing silica fume is much more complex. In this paper, by considering the production of calcium hydroxide in cement hydration and its consumption in the pozzolanic reaction, a numerical model is proposed to simulate the hydration of concrete containing silica fume. The heat evolution rate of silica fume concrete is determined from the contribution of cement hydration and the pozzolanic reaction. Furthermore, the temperature distribution and temperature history in hardening blended concrete are evaluated based on the degree of hydration of the cement and the mineral admixtures. The proposed model is verified through experimental data on concrete with different water-to-cement ratios and mineral admixture substitution ratios.