• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.4
• /
• pp.408-413
• /
• 1995

We investigated the effect of mechanical backside damage upon minority carrier recombination lifetime measurement in Czochralski silicon substrate by laser excitation/microwave reflection photoconductance decay method. The intensity of mechanical damage was evaluated by X-ray double crystal rocking curve, X-ray section topography and wet oxidation/preferential etch methods. The data indicate that the higher the mechanical damage intensity, the lower the minority carrier lifetime, and the threshold full width at half maximum value which affect minority carrier lifetime measurement is about 13 secs.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.18-23
• /
• 1992

Recently, SSPAs(Solid-State Power Amplifiers) with high linearity and efficiency replace TWTAs (Traveling-Wave-Tube Amplifiers) in satellite transponders. In this paper, a power amplifier with maximum output power is designed and constructed using GaAs FET(MGF-1302) as a test model for the development of SSPAs. For conjugate matching of input and output network, transimission lines and stubs are optimized using microwave CAD program, LINMIC+. Power amplifier is realized on the teflon substrate($\in$S1rT=2.45) with a bandwidth of 1GHz at a center frequency of 8GHz. Maximum stable gain of simulation and simulation and experimental result is obtained 9.23, 7.65 dB, respectively.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.181-184
• /
• 2001

A coplanar waveguide(CPW) on a dielectric substrate consists of a center strip conductor with semi-infinite ground planes on either side. This type of waveguide offers several advantages over microstrip line. It facilitates easy shunt as well as series mounting of active and passive devices. It eliminates the need for wraparound and via holes, and it has a low radiation loss. These, as well as several other advantages, make CPW ideally suited for microwave integrated circuit applications. However, very little information is available in the literature on models for CPW discontinuities. This lack of sufficient discontinuity models for CPW has limited the application of CPW in microwave circuit design. We presented for the characteristics of coplanar waveguide open end capacitance and series gap capacitance. Measurements by utilizing the resonance method were made and the experimental data confirmed the validity of theories. The relationships between the CPW capacitances and the physical dimensions were studied.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.6
• /
• pp.50-56
• /
• 2000

The integrated circuit interconnection lines are experimented with patterned ground shields (PGS) at microwave frequencies. Measurement results demonstrate that the PGS can significantly reduce the power loss through the interconnect lines over wide frequency ranges as the PGS shields the lossy silicon substrate. The transmission line characteristics of the PGS interconnect lines are analyzed and identified that the PGS reduces the wave length of the interconnect line.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.6
• /
• pp.1275-1279
• /
• 2012

In this paper, we design of dual-band microstrip antenna for wireless communication. We used IEEE 802.11a and Hyper LAN (5.725~5.825 GHz). The proposed antenna substrate is FR-4, size is $22mm{\times}23mm$, thickness is 1.6mm and used to CST Microwave Studio 2010 program. As a result the simulation has good result and good return loss below -10 dB at 5 GHz and 5.8 bandwidth.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.342-345
• /
• 2014

An active frequency doubler monolithic microwave integrated circuit (MMIC) for E-band transceiver applications is presented in this letter. This MMIC has been fabricated in a commercial $0.1-{\mu}m$ GaAs pseudomorphic high electron mobility transistor (pHEMT) process on a 2-mil thick substrate wafer. The fabricated MMIC chip has been measured to have a high output power performance of over 13 dBm with a high fundamental leakage suppression of more than 38 dBc in the frequency range of 71 to 86 GHz under an input signal condition of 10 dBm. A microstrip coupled line is used at the output circuit of the doubler section to implement impedance matching and simultaneously enhance the fundamental leakage suppression. The fabricated chip is has a size of $2.5mm{\times}1.2mm$.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.134-137
• /
• 2002

A new LTCC material in the $PbWO_4-TiO_2-B_2O_3-CuO$ system was developed. The developed material can be sintered at $850^{\circ}C$ and its dielectric properties are $\varepsilon_r=20-25, Q\timesf_o=30000~50000GHz$ , and $\tau_f=0.2~30ppm/^{\circ}C$, depending on the components moi ratio. Due to its low sintering temperature and microwave dielectric properties, the developed material can be used as a LTCC substrate for fabrication of multilayered microwave communication module set. In present study, using this material, tape casting condition was established. With this processing condition, a T-resonator was fabricated and its electrical properties were examined. Also, a 2-Pole band pass filter was fabricated and its frequency characteristics were compared with simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.270-277
• /
• 2013

In this paper, we propose a wideband ridge SIW(Ridge Substrate Integrated Waveguide)-to-SIW(Substrate Integrated Waveguide) transition. The proposed transition structure is designed to acquire a wide bandwidth by inserting through via holes at the regular interval for an impedance matching and an E-field mode matching method. The measurement results show a fractional bandwidth is 29.1 % at 20 dB return loss from the center frequency(11 GHz). The maximum insertion loss is 0.49 dB from 9.21 GHz to 12.41 GHz.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1720-1723
• /
• 2000

Boron doped conducting diamond thin film were grown on Si substrate by microwave plasma chemical vapor deposition from a gaseous feed of hydrogen, acetone/methanol and solid boron. The doping level of boron was controlled from 0ppm to $10^4$ppm (B/C). The Si substrate was tilted ca. 10$^{\circ}$ to make Si substrate have different height and temperature. Experimental results show that same condition but different temperature of Si substrate by height made different crystalline of diamond thin film. There were appeared 3$\sim$4 step of different crystalline morphology of diamond. To characterize the boron-doped diamond thin film, Raman spectroscopy was used for identification of crystallinity. To survey surface morphology, microscope was used. Grain size was changed gradually by different temperature due to different height. The Raman spectrum of film exhibited a sharp peak at 1334$cm^{-1}$, which is characteristic of crystalline diamond. The lower position of diamond film position, the more non-diamond component peak appeared near 1550$cm^{-1}$.

• Clean Technology
• /
• v.22 no.4
• /
• pp.250-257
• /
• 2016

As an attempt to replacing petroleum-based chemicals with bio-based ones, synthesis of furfural from biomass-derived xylose attracts much attention in recent days. Conventionally, furfural from xylose has been produced via the utilization of highly corrosive, toxic, and environmentally unfriendly mineral acids such as sulfuric acid or hydrochloric acid. In this study, microwave-assisted biphasic reaction process in the presence of novel bio-based heterogeneous acid catalysts was developed for the eco-benign and effective synthesis of furfural from xylose. The microwave was irradiated for reaction acceleration and a biphasic system consisting of $H_2O$ : MIBK (1 : 2) was designed for continuous extraction of furfural into the organic phase in order to reduce the undesired side products formed by decomposition/condensation/oligomerization in the acidic aqueous phase. Moreover, sulfonated amorphous carbonaceous materials were prepared from wood powder, the most abundant lignocellulosic biomass. The prepared catalysts were characterized by FT-IR, XPS, BET, elemental analysis and they were used as bio-based heterogeneous acid catalysts for the dehydration of xylose into furfural more effectively. For further optimization, the effect of temperature, reaction time, water/organic solvent ratio, and substrate/catalyst ratio on the xylose conversion and furfural yield were investigated and 100% conversion of xylose and 74% yield of furfural was achieved within 5 h at $180^{\circ}C$. The bio-based heterogeneous acid catalysts could be used three times without any significant loss of activity. This greener protocol provides highly selective conversion of xylose to furfural as well as facile isolation of product and bio-based heterogeneous acid catalysts can alternate the environmentally-burdened mineral acids.