• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.8
• /
• pp.617-623
• /
• 2008

The membrane filter adhered with nanostructured porous layer was made by heat treatment after deposition of nanoparticle-agglomerates sintered in aerosol phase onto a conventional micron-fibrous metal filter as a substrate filter. The Sintered-Nanoparticle-Agglomerates-coated NanoStructured porous layer Membrane Filter (SNA-NSMF), whose the filtration performance was improved compared with the conventional metal membrane filters, was developed by adhesion of nanoparticle-agglomerates of dendrite structure sintered onto the micron-fibrous metal filter. The size of nanoparticle-agglomerates of dendrite structure decreased with increasing the sintering temperature because nanoparticle-agglomerates shrank. When shrinking nanoparticle-agglomerates were deposited and treated with heat onto the conventional micron-fibrous metal filter, pore size of nanostructured porous layer decreased. Therefore, pressure drops of SNA-NSMFs increased from 0.3 to 0.516 kPa and filtration efficiencies remarkably increased from 95.612 to 99.9993%.

• Journal of the Korean Society of Tobacco Science
• /
• v.20 no.2
• /
• pp.205-209
• /
• 1998

This study was conducted to evaluate the effect of triacetin(TA) treatment during manufacturing carbon dual filter for the adsorption of cigarette smoke components by activated carbons. The measurements were carried out by separation of activated carbon from carbon dual filter, and the specific surface area analyzed. The specific surface area of activated carbon from the domestic cigarette filter and from the foreign cigarette filter by degassing at 9$0^{\circ}C$ was 163$\pm$32$m^2$/g, and 16.6$\pm$1.9$m^2$/g, respectively. Those values were very lower than that of degassing at 35$0^{\circ}C$ (Domestic brand: 952$\pm$30$m^2$/g, and Foreign brand: 847$\pm$73$m^2$/g). By comparing the adsorption capacity of acetone and benzene with and without triacetin treated activated carbon, there was a 20% reduction of adsorption capacity by 5% triacetin treatment. Also, from the cilia toxicity test with carbon dual filter treated 0 % TA and 8 % TA, the cilia survival time was 706$\pm$74sec. and 603$\pm$64sec. for 0% TA and 8% TA, respectively. The delivery rate of vapour phase of cigarette smoke, which consists of main components of cilia toxicity, was higher at 8% TA filter than 0 % TA filter. Our results indicate that the treated TA covered the micro-pore of activated carbon, and then reduced specific surface area, finally, decreased the adsorption of vapour phase from cigarette smoke.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.3
• /
• pp.22-30
• /
• 2009

GPS and INS integrated systems are expected to become commonly available as a result of low cost Micro-Electro-Mechanical Sensor (MEMS) technology. However, the current performance achieved by low cost sensors is still relatively poor due to the large inertial sensor errors. This is particularly prevalent in the urban environment where there are significant periods of restricted sky view. To reduce the inertial sensor error, GPS and low cost INS are integrated using a Loosely Coupled Kalman Filter architecture which is appropriate in most applications where there is good satellite availability. In this paper, we present the GPS/INS sensor Integration using Loosely Coupled Kalman Filter approach. We also compare the simulation results of Wander Azimuth Strapdown Mechanization Scheme with the reference values generated by the ZH35C trajectory simulator that is describe mathematically either by the geometry of the path, or as the position of the object over time.

• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.306-311
• /
• 2003

In this paper, we modeled the incident beam in order to analyze and evaluate the optical thin film device for wavelength division multiplexing in optical telecommunication network. As applied ray tracing method to the optical path, we were compared the accuracy of coupling efficiency simulated by two modeling methods. In the results of sinulation, ceil modeling method was preferred to annual modeling method in micro-optic device because of accuracy for coupling efficiency and Gaussian intensity distribution. In the results of optimal simulation for optical device using thin film filter, the distance (d1) between optical fiber and GRIN lens, the distance (d2) between GRIN lens and thin film filter and the coupling efficiency were 0.24 mm, 0.25 mm and -0.11 ㏈ respectively. As d2 was displaced at 0.25 mm and d1 was varied in order to evaluate the optimal value, d1 and maximum coupling efficiency were 0.24 mm and -0.35㏈, respectively. Then the results of experiment were corresponded to that of optimal simulation by cell modeling and it was possible to analyze the performance for optical device using thin film filter by the simulation.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.37 no.2
• /
• pp.106-114
• /
• 2017

This paper presents an automated subsurface micro void detection technique based on pulsed infrared thermography for inspecting epoxy molding compounds (EMC) used in electronic device packaging. Subsurface micro voids are first detected and visualized by extracting a lock-in amplitude image from raw thermal images. Binary imaging follows to achieve better visualization of subsurface micro voids. A median filter is then applied for removing sparse noise components. The performance of the proposed technique is tested using 36 EMC samples, which have subsurface (below $150{\mu}m{\sim}300{\mu}m$ from the inspection surface) micro voids ($150{\mu}m{\sim}300{\mu}m$ in diameter). The experimental results show that the subsurface micro voids can be successfully detected without causing any damage to the EMC samples, making it suitable for automated online inspection.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.2
• /
• pp.140-145
• /
• 2013

This paper proposes an efficient integration method for GPS (Global Positioning System) and INS (Inertial Navigation System). To obtain accuracy and computational conveniency at the same time with low cost global positioning system receivers and micro mechanical inertial sensors, a new mechanization method and a new filter architecture are proposed. The proposed mechanization method simplifies velocity and attitude computation by eliminating the need to compute complex transport rate related to the locally-level frame which continuously changes due to unpredictable vehicle motions. The proposed filter architecture adopts two heterogeneous filters, i.e. position-domain Hatch filter and velocity-aided Kalman filter. Due to distict characteristics of the two filters and the distribution of computation into the two hetegrogeneous filters, it eliminates the cascaded filter problem of the conventional loosly-coupled integration method and mitigates the computational burden of the conventional tightly-coupled integration method. An experiment result with field-collected measurements verifies the feasibility of the proposed method.

• Transactions of Materials Processing
• /
• v.14 no.5 s.77
• /
• pp.473-476
• /
• 2005

The demand of on-chip total analyzing system with MEMS (micro electro mechanical system) bio/chemical sensor is rapidly increasing. In on-chip total analyzing system, to detect the bio/chemical products with submicron feature size, a filtration system with nano-filter is required. One of the conventional methods to fabricate nano-filter is to use direct patterning or RIE (reactive ion etching). However, those procedures are very costly and are not suitable fur mass production. In this study, we suggested new fabrication method for a nano-filter based on replication process, which is simple and low cost process. After the Si master was fabricated by laser interference lithography and reactive ion etching process, the polymeric mold was replicated by UV-imprint process. Metallic nano-filter was fabricated after removing the polymeric part of metal deposited polymeric mold. Finally, our fabrication method was applied to metallic nano-filter with $1{\mu}m$ pitch size and $0.4{\mu}m$ hole size for bacteria sensor application.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.5A
• /
• pp.494-499
• /
• 2008

In this study, a Software Defined Radio(SDR) technology-based digital filtering technique applicable to a multiple channel processing system such as a wireless mobile communication system using Code Division Multiple Access(CDMA) technology is proposed. The technique includes a micro-processor to redesign Finite Impulse Response(FIR) filter coefficients according to specific system information and to download the filter coefficients to one digital Band Pass Filter(BPF) to reconfigure another system. The feasibility of the algorithm is verified by implementing a multiple channel signal generator that is reconfigurable to other system profiles, including those for a CDMA system and a WCDMA system on identical hardware platform.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.10
• /
• pp.24-28
• /
• 1992

A new design method of microstrip wide band VHF tunable bandpass filters using varacter diodes is presented. In the proposed filter both the input and output ports are coupled through capacitors, and an open micro-strip line is inserted between the coupled line in order to obtain the desired degree of coupling. The optimized filter responseses for the frequency range of 220-404MHz by TOUCH-STONE are compared with the measured ones.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.07a
• /
• pp.114-115
• /
• 2003

최근 급속히 성장하고 있는 Wavelength-division-multiplexing (WDM) 시스템에 파장가변 필터는 핵심적인 소자로 적용될 수 있으며, 높은 가격 경쟁력과 광학 필터로서 좋은 특성과 높은 가변 특성을 구현할 수 있다. 이러한 파장가변 필터는 multi-beam 간섭을 이용하고, Micro electro mechanical systems (MEMS) 공정 기술인 벌크 마이크로 머시닝 기술을 이용하여 구현되어지고 있다. 또한 파장 가변 필터는 Optical-performance monitoring, Spectrometer, Optical noise filter, Sensor 등 여러 분야에 응용될 수 있다. (중략)