• 한국전기전자재료학회논문지
• /
• 제30권4호
• /
• pp.235-240
• /
• 2017

The effect of particle sizes on the aerosol deposition (AD) of Cu films is investigated in order to understand the deposition behaviors of metal powder during the AD process. The Cu coatings fabricated by using $2{\mu}m$ Cu powders had a dense microstructure, a high deposition rate ($1.6{\pm}0.2{\mu}m/min$), and low resistance ($9.42{\pm}0.4{\mu}{\Omega}{\cdot}cm$) compared to that from using Cu powder with a particle size greater than $5{\mu}m$. Also, from estimating the internal micro-strain of Cu films, the Cu coatings fabricated by using $2{\mu}m$ Cu particles exhibited a high micro-strain value of $3.307{\times}10^{-3}$. On the other hand, the strain of Cu coatings fabricated with $5{\mu}m$ particles was decreased to $2.76{\times}10^{-3}$. These results seem to show that the impacted Cu particles are compressed and flattened by shock waves, and that their bonding is associated with the high internal micro-strain caused by plastic deformation.

• Journal of Welding and Joining
• /
• 제34권4호
• /
• pp.23-27
• /
• 2016

A 3D printed metal part and thermal plastic polymer part were joined by direct laser irradiation. The 3D metal part was fabricated by using DED(Direct Energy Deposition) with STS316 material. The experiment was carried out through no patterned metal surface, 3D metal printed surface and micro laser patterned surface. The most secure joining quality was obtained at the laser micro patterned surface specimen and the counterparts of polymers were PLA and PE based thermo plastics. The applied laser power was 350Watt and the distance of patterns was maintained at $150{\mu}m$. The laser line width was optimized at $450{\mu}m$ and the laser micro pattern depth was $180{\mu}m$ for the best joining quality. Based on the result analysis, the possibility of laser material joining for metal to polymer was proposed and multi-material joining will be possible in 3D laser direct material fabrication.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.451-462
• /
• 1995

Single overload tests performed to examine the crack retardation behavior for the specimen thickness and overload ratios. Delayed crack length was tend to increase in small thickness and big overload ratio but was difference between delayed crack length and plastic zone size that expected in specimen thickness. So retardation behavior that estimated in plastic zone size, was not sufficient. Crack tip branching and striation distribution, secondary mechanisms that effected in retardation behavior, was examined by experiment and finite element analysis. Crack tip branching was affected by micro structure, and appeared the more complicatedly according to increasing damage by overload and decreasing crack driving force in base line stress level. And crack tip branching the branching angle decreased crack driving force in the crack tip. And a characteristic of the fractography on retardation zone was that striation distribution did not appear due to decreased crack driving force.

• 한국표면공학회지
• /
• 제42권4호
• /
• pp.173-178
• /
• 2009

DLC film was synthesized on plastic injection mold(SKD11, $30\;mm\;{\times}\;19\;mm\;{\times}\;0.5\;mm$) and Si(100) wafer for 2 h at $130^{\circ}C$ under 6 mTorr using hybrid method of rf sputtering and ion source. The obtained film was analysed by Raman spectroscopy, AFM, TEM, Nano indenter and scratch tester, etc. The film was defined as an amorphous phase. In the Raman spectrum, broad peak of $sp^2$-bonded carbon attributed to graphite at $1550\;cm^{-1}$ were observed, and the ratio of ID($sp^3$ diamond intensity)/IG($sp^2$ graphite intensity) was approximately 0.54. The adhesion of DLC film was more than 80 N with scratch tester when $0.2\;{\mu}m$ thickness Cr was coated as interlayer. The micro-hardness was distributed at 35~37 GPa. The friction coefficient was 0.02~0.07, and surface roughness(Ra) was 0.34~1.64 nm. The lifetime of DLC coated plastic injection mold using as a connector part in computer was more than 2 times of non-coated mold.

• 비파괴검사학회지
• /
• 제32권1호
• /
• pp.20-26
• /
• 2012

본 연구의 목적은 비접촉식 레이저 여기 표면파의 비선형성 계측을 통하여 소성 변형된 알루미늄 합금의 소성변형을 평가하고자 하는 데 있다. 슬릿마스크와 고출력 펄스 레이저를 통한 선배열 레이저빔을 이용하여 협대역의 표면파를 발생 시켰으며, 표면파의 음향 비선형 특성을 이용하기 위하여 슬릿 마스크의 열림 폭과 간격을 변화시킴으로써 레이저 여기 표면파의 주파수 특성을 제어하였다. 스트로크 제어를 통한 인장시험을 통하여 단계별 인장 소성변형 정도를 달리하는 시험편을 제작하였다. 실험결과 인장 소성 변형율이 커짐에 따라 음향 비선형 파라미터는 증가하였으며, 경도 및 EBSD 측정결과 손상의 정도와 매우 밀접한 관계를 보였다. 결과적으로 본 연구에서의 레이저 여기 표면파의 비선형 평가기법은 알루미늄 합금의 소성변형 평가에 매우 유용할 것으로 판단된다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2001년도 춘계학술대회 논문집
• /
• pp.190-195
• /
• 2001

In the present paper computational simulation of a concrete dam is performed to determine the effect of vertical ground motions on earthquake response of concrete dams. Cyclic and dynamic versions of the plastic-damage model proposed by Lee and Fenves are used to represent micro-crack development and crack opening/closing, which is important mechanism in nonlinear damage analysis of concrete structures subject to strong earthquake loading. The result shows that the vertical component of ground motion effects on final crack patterns and consequently, on displacement response.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 1999년도 1st Korea-Japan Advanced Semiconductor Packaging Technology Seminar
• /
• pp.127-154
• /
• 1999

Interconnect - Wire bonding-> Flip chip interconnect ; At research step, Au stud bump bonding seems to be more proper .Package -Plastic package-> $Z_{0}$ controlled land grid package -Flip Chip will be used for RF ICs and CSP for digital ICs -RF MCM comprised of bare active devices and integrated passive components -Electrical design skills are much more required in RF packaging .Passive Component -discrete-> integrated -Both of size and numbers of passive components must be reduced

• 한국식물병리학회:학술대회논문집
• /
• 한국식물병리학회 2005년도 한국식물병리학회 임시총회 및 춘계학술발표회
• /
• pp.87.2-88
• /
• 2005

• 반도체디스플레이기술학회지
• /
• 제3권2호
• /
• pp.23-26
• /
• 2004

Thin film is one of the most general structures used in micro-electro-mechanical systems (MEMS). To measure the mechanical properties of SU-8 film, tensile testing was adopted which offers not only elastic modulus but also yield strength and plastic deformation by load-displacement curve. Tensile testing system was constructed with linear guided servo motor for actuation, load cell for force measurement and dual microscope for strain measurement.

• 오토저널
• /
• 제9권3호
• /
• pp.76-84
• /
• 1987

A study has been made to clarify the microstructural effect on static tensile properties of the dual phase steel, in which the martensitic phase encapsulated islands of ferritic phase. The main results are as follows: Yield strength is associated with the degree of plastic constraint factor and tensile strength increases with increasing of strain hardening exponent. Also, the variation of ductility is dependent upon the amount of micro-brittle facets.