• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.159.1-159.1
• /
• 2011

Partial oxidation reformer was fabricated and operated using commercial transportation fuels. Fuel injector and heating coil were used for fuel atomization and startup, respectively. The reformer was designed to produce syngas for $150{\sim}200W_e$ class solid oxide fuel cell. The reformer was operated in the $O_2$/C range between 0.6 and 0.8 while the capacity was fixed at $150W_e$. The temperature range in catalyst bed was between $500^{\circ}C$ and $900^{\circ}C$. Only 83% fuel was converted to $H_2$, CO, $CO_2$ and $CH_4$ at the operating conditions. The lowest temperature increase to $700^{\circ}C$ when the reformer was operated at $200W_e$, Although the temperature profiles was improved, fuel conversion was 88%. On the other hand, fuel was completely converted when micro-reactor operated at the same condition. This difference maybe due to aromatic compounds formation at homogeneous region. In addition, a significant amount of coke deposition was observed at vent line. Homogeneous reaction depends on the degree of mixing. For this purpose, two fluid nozzle and Ultra sonic injector were compared to investigate the effect of atomization. Sauter mean diameter(SMD) of Ultra sonic injector was lower than two-fluid nozzle at test condition. However, conversion efficiency and fuel conversion were not improved by using two-fluid nozzle. these results imply that the temperature of homogeneous reaction region should be controlled to prevent coke formation.

• Tribology and Lubricants
• /
• v.30 no.3
• /
• pp.139-145
• /
• 2014

Nowadays, most micro-patterns are manufactured during flow line production. However, a conventional rotary chemical mechanical polishing (CMP) system has a limited throughput for the fabrication of large and flexible electronics. To overcome this problem, we propose a novel linear roll-CMP system for the planarization of large-area electronics. In this paper, we present a statistical analysis on the linear roll-CMP process of copper-clad laminate (CCL) to determine the impacts of process parameters on the material removal rate (MRR) and its non-uniformity (NU). In the linear roll-CMP process, process parameters such as the slurry flow rate, roll speed, table feed rate, and down force affect the MRR and NU. To determine the polishing characteristics of roll-CMP, we use Taguchi's orthogonal array L16 (44) for the experimental design and F-values obtained by the analysis of variance (ANOVA). We investigate the signal-to-noise (S/N) ratio to identify the prominent control parameters. The "higher is better" for the MRR and "lower is better" for the NU were selected for obtaining optimum CMP performance characteristics. The experimental and statistical results indicate that the down force and roll speed mainly affect the MRR and the down force and table feed rate determine the NU in the linear roll-CMP process. However, over 186.3 N of down force deteriorates the NU because of the bending of substrate. Roll speed has little relationship to the NU and the table feed rate does not impact on the MRR. This study provides information on the design parameter of roll-CMP machine and process optimization.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.498-498
• /
• 2013

Atmospheric Pressure Plasmas have pioneered a new field of plasma for biomedical application bridging plasma physics and biology. Biological and medical applications of plasmas have attracted considerable attention due to promising applications in medicine such as electro-surgery, dentistry, skin care and sterilization of heat-sensitive medical instruments [1]. Traditional approaches using electronic devices have limits in heating, high voltage shock, and high current shock for patients. It is a great demand for plasma medical industrial acceptance that the plasma generation device should be compact, inexpensive, and safe for patients. Microwave-excited micro-plasma has the highest feasibility compared with other types of plasma sources since it has the advantages of low power, low voltage, safety from high-voltage shock, electromagnetic compatibility, and long lifetime due to the low energy of striking ions [2]. Recent experiment [2] shows three-log reduction within 180-s treatment of S. mutans with a low-power palm-size microwave power module for biomedical application. Experiments using microwave plasma are discussed. This low-power palm-size microwave power module board includes a power amplifier (PA) chip, a phase locked loop (PLL) chip, and an impedance matching network. As it has been a success, more compact-size module is needed for the portability of microwave devices and for the various medical applications of microwave plasma source. For the plasma generator, a 1.35-GHz coaxial transmission line resonator (CTLR) [3] is used. The way of reducing the size and enhancing the performances of the module is examined.

• Cartoon and Animation Studies
• /
• s.12
• /
• pp.56-72
• /
• 2007

The purpose of this study is to analyze the characteristics of animation cluster in Chuncheon. It has been over 10 years since Chuncheon was designated as the cluster raising the animation industry. The Chuncheon cluster is trying to differentiate through managing several unique strategies. In order to realize the micro-regionalism, it focuses on co-production not with domestic companies but with foreign companies. Especially, for establishing the whole concrete production pipe-line, it concerns to make co-production contracts dealing with not only for the main production part but also pre- and post-production parts. Based on these production experience, it is building the production complex in the name of ICT convergence cluster. The changed role of the policy-management organization(Gangwon Information & Multimedia Corporation, GIMC) enables these differentiated strategies by itself. The establishment of the Asian Animation Round(AAR) is recognized as the characteristic of macro-regionalism. Starting from the year of 2006, the AAR tries to place Chuncheon as the hub of animation production in Asia and focuses on constructing the network of animation production countries that have developed their production capabilities through sub-contracts. This type of production and market bloc has not been made before.

• Journal of Biosystems Engineering
• /
• v.33 no.5
• /
• pp.348-354
• /
• 2008

Egg grading is determined by exterior and interior quality. Among the evaluation methods for the egg quality, a candling method is common to identify eggs with cracked shells and interior defects. But this method is time-consuming and laborious. In addition, practically, it is challenging to detect hairline and micro cracks. In this study, an on-line inspection system based on acoustic resonance frequency analysis was developed to detect hairline cracks on eggshells. A roller conveyor was used to transfer eggs along one lane to the impact position where each of eggs rotated by the roller was excited with an impact device at four different locations on the eggshell equator. The impact device was consisted of a plastic hammer and a rotary solenoid. The acoustic response of the egg to the impact was measured with a small condenser microphone at the same position as the impact device was installed. Two acoustic parameters, correlation coefficient for normalized power spectra and standard deviation of peak resonant frequencies, were used to detect cracked eggs. Intact eggs showed relatively high correlations among the four normalized power spectra and low standard deviations of the four peak resonant frequencies. On the other hand, cracked eggs showed low correlations and high standard deviations as compared to the intact. This method allowed a crack detection rate of 97.6%.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.6
• /
• pp.2397-2402
• /
• 2015

Previous studies have shown that miR-454 plays an important role in a variety of biological processes in various human cancer cells. However, the underlying mechanisms of this microRNA in colorectal cancer (CRC) cells remain largely unknown. In the present study, we investigated the miR-454 role in CRC cell proliferation. We found that miR-454 expression is markedly upregulated in CRC tissues and CRC cells compared with the matched tumor adjacent tissues and the FHC normal colonic cell line. Ectopic expression of miR-454 promoted the proliferation and anchorage-independent growth of CRC cells, whereas inhibition of miR-454 reduced this effect. Bioinformatics analysis further revealed cylindromatosis (CYLD), a putative tumor suppressor as a potential target of miR-454. Data from luciferase reporter assays showed that miR-454 directly binds to the 3'-untranslated region (3'-UTR) of CYLD mRNA and repressed expression at both transcriptional and translational levels. In functional assays, CYLD-silenced in miR-454-in-transfected SW480 cells have positive effect to promote cell proliferation, suggesting that direct CYLD downregulation is required for miR-454-induced CRC cell proliferation. In sum, our data provide compelling evidence that miR-454 functions as an onco-miRNA, playing a crucial role in the promoting cell proliferation in CRC, and its oncogenic effect is mediated chiefly through direct suppression of CYLD expression.

• Journal of the Korean association of regional geographers
• /
• v.15 no.2
• /
• pp.204-214
• /
• 2009

The purpose of this paper is to elucidate the formation processes of Hwaeumneup in Cheonseong Mountain which was designated as Wetland Conservation Area in 2002, and to offer data essential to sustainable management of wetland. According to wetland core samples and carbon dating of humus, grassland of Hwaeumneup Wetland Reservation resulted from slash-and-burn agriculture in no reference with climatic changes of last glacial period. And Hwaeumneup is a alpine wetland that is formed as rain water over Cheonseong Mountain crest area infiltrates into bedrock, springs out along joint line below main ridge, and dampens gentle grassland. It needs to support dense vegetation of southwestern ridge of Wetland Reservation in order to sustain water volumn of Hwaeumneup wetland, and to keep from breakdown of block dam at downstream fringe of wetland. And it needs to measure and analyse micro-topography and hydrology changes in Hwaeumneup Wetland Reservation through periodic monitoring.

• KIEE International Transactions on Power Engineering
• /
• v.3A no.1
• /
• pp.27-34
• /
• 2003

In this paper, the power conditioner composed of the stand-alone single-phase squirrel cage rotor type self-excited induction generator (SEIG) driven by prime movers such as a wind turbine and a micro gas turbine (MGT) is presented by using the steady-state circuit analysis based on the two nodal admittance approaches using the per-unit frequency in addition to a new state variable defined by the per-unit slip frequency along with its performance evaluations for the stand-alone energy utilizations. The stande-alone single-phase SEIG operating performances in unregulated voltage control loop are then evaluated on line under the conditions of the speed change transients of the prime mover and the stand-alone electrical passive load power variations with the simple theoretical analysis and the efficient computation processing procedures described in the part I of this paper. In addition, a feasuible PI controlled feedback closed-loop voltage regulation scheme of the stande-alone single-phase SEIG is designed on the basis of the static VAR compensate. (SVC) and discussed in experiment for the promising stand-alone power conditioner. The experimental operating performance results are illustrated and give good agreements with the simulation ones. The simulation and experimental results of the stand-alone single-phase SEIG with the simple SVC controller for its stabilized voltage regulation prove the practical effectiveness of the additional SVC control loop scheme including the PI controller with fast response characteristics and steady-sate performance improvements.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.743-747
• /
• 2003

The improvement of luminance and luminous efficiency is the one of the most important part in AC-PDPs. To achieve high luminance and luminous efficiency, high VUV emission efficiency is needed. We measured the emission spectra of vacuum ultraviolet(VUV) and infrared(IR) rays in surface discharge AC-PDP with Ne-Xe mixture gas. The influence of Ne-Xe gas-mixture ratio on resonance state $Xe^{\ast}(3P_{1})$ and exited state $Xe^{\ast}(3P_{2})$ has been investigated. It is found that the intensity of VUV 147nm emission is proportional to that of the IR 828 nm emission, and the VUV 173nm emission is roughly proportional to that of the IR 823nm emission. The electron temperature and plasma density have been experimentally measured from the center of sustaining electrode gap by a micro Langmuir probe in AC-PDPs. The plasma density from the center of sustaining electrode gap are shown to be maximum value of $9{\times}10^{11}cm^{-3}$, where the electron temperature is about 1.6 eV in this experiment

• Journal of the Korean Society of Costume
• /
• v.53 no.5
• /
• pp.79-95
• /
• 2003

The purpose of this study is firstly to survey the social and cultural background of 20th century and women´s status, and to identify what the ideal body is like and what the elements of outer garment and underwear are and the techniques to incarnate the ideal beauty. Various papers are referenced for theoretical study and the elements and techniques of underwear are analyzed based on photographical materials. This paper concludes as follows. In 1960´s, ideal beauty was small bust, long legs, which showed extremely slim Mini-skirt look. Thinly or no padded brassiere were worn for small bust, and pants-style short panty girdles were popular as they used to wear pants frequently. Lycra replaced all the closures, bones, seams and gave freedom with light weight. In 1970´s, a natural human body without sex specific was in vogue. Therefore, the non-structural knits without a pad or lining or the shirts dress were widespread for a Natural look and the naturally molded brassiere or girdles were worn as the underwears. In 1980´s, the women with powerful muscle appear which emphasized liveliness and healthfulness. The body conscious represented by wide shoulder, plump breast, accented waist, small hips, and long legs has been embodied. Outer garments emphasized women power and healthy beauty with Power suit and Form-fitting style, and underwears made the breast plump with padded brassiere and emphasized waist and hips with waspie. In 1990´s, ideal beauty was slim body with big bust and the outer garments emphasized body line of women with Hourglass silhouette. Push-up bra which emphasizes the valley of breast and supports the breast upward and the control tights for slim waist, flat abdomen, small hips, and long and slim legs have been useful as underwears. Multi-functional micro-fiber has been ideal for sculpting women body.