• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.771-775
• /
• 2015

In this paper, we designed and fabricated low cost imprinting process for micro patterning on FCCL (flexible copper clad laminate). Compared to conventional imprinting process, developed fabrication method processing imprint and UV photolithography step simultaneously and it does not require resin etch process and it can also reduce the fabrication cost and processing time. Based on proposed method, patterns with $10{\mu}m$ linewidth are fabricated on $180mm{\times}180mm$ FCCL. Compared to conventional methods using LDI (laser direct imaging) equipment that showed minimum line with $10{\sim}20{\mu}m$, proposed method shows comparable pattern resolution with very competitive price and shorter processing time. In terms of mass production, it can be applied to fabrication of large-area low cost applications including FPCB.

• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.1563-1566
• /
• 2002

A 16-bit adiabatic datapath for micro-power RISC processor is designed. The datapath is composed of a 3-read and 1-write multi-port adiabatic register file and an arithmetic and logic unit. A four-phase clock generator is also designed to provide supply clocks fer adiabatic circuits and the driving capability control scheme is proposed. All the clock line charge on the capacitive interconnections is recovered to recycle energy. Adiabatic circuits are designed based on efficient charge recovery logic(ECRL) and are implemented using a 0.35 fm CMOS technology. Functional and energy simulation is carried out to show the feasibility of adiabatic datapath. Simulation results show that the power consumption of the adiabatic datapath including supply clock generator is reduced by a factor of 1.4∼1.5 compared to that of the conventional CMOS.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.834-837
• /
• 1993

This paper describes the implementation of an autonomous fuzzy logic controller. The controller is endowed with basic control principles and learning constructs which enable it to autonomously modify its control policy based on system performance. The controller lies dormant when system response is satisfactory but if rapidly initiates adaptation in real time when adverse performance is observed. The autonomous fuzzy controller is implemented on an Intel MCS-51 series micro-controller board using an inexpensive 8-bit Intel 8031 processor. The 11.06 MHz micro-controller operates at a rate exceeding 200 "global" look-up table reinforcements per second. This is important when developing practical on-line adaptive controllers for fast systems. It is also significant because an initial controller look-up table could be incorrect or non-existent. The relatively high learning rate enables the controller to learn to control a system even while it is controlling it.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.17
• /
• pp.7749-7754
• /
• 2015

Background: Currently, cationic liposome has become the commonly used vehicles for gene transfection. Furthermore, one of the most significant steps in microRNAs expression studies is transferring microRNAs into cell cultures successfully. In this study we aim to approach the feasibility of transfection of cervical cancer cell lines mediated by liposome and to obtain the optimized transfection condition for cervical cancer cell lines. Materials and Methods: $Lipofectamine^{TM}2000$ as the carrier, miR-101 mimic was transfected into Hela cells and Siha cells. Using green fluorescent protein as reporter gene, to set different groups according to cell seeding density, the amount of miRNA, miRNA and the proportion of Liposomes, Whether to add serum into medium to study their impact on the liposomal transfection efficiency. Finally, MTT assay was used to analyze the relative minimal cell toxicity of liposome reagents. Results: The seeding density of Hela cell line and Siha are $1.5{\times}10^4$ (per well of 24 well plates), miRNA amount is 1ul of both, the ratio of miRNA and liposome is 1:0.5 of Hela cell line; 1:0.7 of Siha cell line respectively, after 24 hours we can get the highest transfection efficiency. Compared with serum medium, only Siha cells cultured with serum-free medium obtained higher transfection efficiency before transfection (P<0.01). MTT assay showed that according to the above conditions which has the lowest cytotoxicity. Conclusions: The method of Liposome to transfected is a suitable way and it can be an efficient reagent for miRNA delivery for Hela cells and Siha cells in vitro. It may serve as a reference for the further research or application.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2008.03a
• /
• pp.51-68
• /
• 2008

When the train enters into a tunnel a high speed, pressure waves are generated inside the tunnel. The pressure waves at propagate in a form of compression wave toward the tunnel exit and a fraction of the compression waves that arrives at the exit of the tunnel are discharged to outside of the tunnel and the remainder is reflected into the tunnel as expansion waves. The compression waves emitted from the tunnel does not radiate in a specific direction but in all directions. If the amplitude of the compression wave is great, it causes noise and vibration, and it is called "Micro-Pressure Wave." "Micro-Pressure Wave" must be considered as a decision for the optimum tunnel cross-section as the amplitude of the compression wave depends on train speed, tunnel length, area of tunnel and train. Therefore, this paper introduces the case study of Micro-Pressure Wave characteristics for determination of tunnel cross section in Honam high speed railway, the pressure inside the tunnel and the micro-pressure waves at tunnel exit were measured at Hwashin 5 tunnel in Kyungbu HSR line. At the same time. a test of train operation model was performed and then the measurement results and test results were compared to verify that the various parameters used as input conditions for the numerical simulations, which were appropriate. Also a model test was performed, in order to analysis of the Micro-Pressure Wave Mitigation Performance by Type of Hood at Entrance Portal.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.250-253
• /
• 2007

It is known that fine straightness of micro-wire can be obtained by removing residual stress induced during the manufacturing processes. Generally, residual stress is removed or minimized through several drawing processes with heat treatment. In this study, the residual stress at each straightening process is calculated and monitored by finite element analyses and the main reason of stress change is investigated.

• Transactions on Control, Automation and Systems Engineering
• /
• v.4 no.1
• /
• pp.38-42
• /
• 2002

Conditions are discussed for operating a dissymmetric human master-small (or micro) slave system in best (large position gain-small velocity gain) conditions allowing higher operator dexterity when real effects (joint compliance, link flexion delay and transmission distortion) are taken into account. It is shown that position PD feedback law advantage for ideal case no longer holds, and that more complicated feedback law depending on real effects has to be implemented with adapted transmission line. Drawback is slowdown of master slave interaction, suggesting to use more advanced predictive methods for the master and more intelligent control law for the slave.

• Journal of electromagnetic engineering and science
• /
• v.16 no.3
• /
• pp.191-193
• /
• 2016

This paper proposes a voltage-controlled oscillator (VCO) that has broadband turning and low-level of phase noise characteristics. Due to the micro-strip line resonant circuit with a low Q value, which is applied to the broadband tuning range, the depreciated phase noise performance is compensated by restraining the harmonics of the oscillating frequency. The VCO was designed according to the proposed structure as well as the conventional structure, and the superiority of the proposed structure was verified through its simulation, fabrication, and measurement.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.319-321
• /
• 2004

We report on progress in developing high-power excimer lasers as well as UV-optics for creating low-temperature poly silicon (LTPS). A new high-power excimer laser offers 315 Watts with high pulse to pulse energy stability. Larger substrates can now be processed in better quality with either the SLS process or the new optics for line beam excimer laser annealing.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.24-31
• /
• 2004

The objective of this work is to suggest a mastless pattern fabrication technique using the combination of machining by Nanoindenter(equation omitted) XP and HF wet etching. Sample line patterns were machined on a borosilicate surface by constant load scratch (CLS) of the Nanoindenter(equation omitted) XP with a Berkovich diamond tip, and they were etched in HF solution to investigate chemical characteristics of the machined borosilicate surface. All morphological data of scratch traces were scanned using atomic force microscope (AFM).