• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.377-381
• /
• 2004

Electrical conductivity of Al-Si-Cu-Mg alloy foams of various density produced in powder metallurgical method has been measured using two probe electrical conductivity measurement method. Compressive mechanical properties such as elastic modulus and plastic plateau stress of foams were evaluated from electrical conductivity using power law relation and scaling laws of foam properties. Uni-axial compression test was also performed. Experimentally measured elastic modulus and plastic plateau stress were compared with the values evaluated from electrical conductivity. The computed values were in good agreement with the experimental result.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.55 no.3
• /
• pp.328-337
• /
• 2022

This study investigated the removal performance of a foam fractionator under seawater conditions. The foam fractionator was tested using a 3×3×3 factorial design for operating conditions by combining different solids concentrations (SS; 1, 5, and 10 mg·L^-1), surface air velocities (SAV; 1.1, 1.5, and 2.1 cm·sec^-1), and hydraulic residence times (HRT; 1, 3, and 6 min) at 16℃. Performance parameters such as daily solids removal rate and efficiency were measured, and a multi-regression model equation was developed accordingly. The daily solids removal rate and removal efficiency varied with the experimental conditions and ranged from 0.14-2.33 g-solids·m^-3-air·day^-1 and 8.9-96.7 %, respectively. Overall, the daily solids removal rate increased with increasing SS and SAV and decreasing HRT, whereas the removal efficiency increased with increasing SAV and HRT and decreasing SS. The daily solids removal rate (g-solids·m^-3-air·day^-1) of the foam fractionator for SAV (cm·sec^-1), SS (mg·L^-1) and HRT (min) were described by the following multi-regression model: Daily solids removal rate [f(z)]=-0.118+0.422SAV+0.094HRT+0.141SS (r²=0.873).

• The Journal of Korean Medicine
• /
• v.28 no.2 s.70
• /
• pp.185-199
• /
• 2007

Objectives : This study was carried out to investigate the inhibitive effect of a combined-herb prescription of Dansam-san (DSS) on formation of foam cells and cytokine. Methods : Experimental formation of foam cells was induced on macrophage RAW 264.7 with ox-LDL. The effect of DSS extract was observed by measuring the changes of CD36, $PPAR-{\Gamma}$, MMP-9, iNOS expression and changes of formation level of foam cells after treating experimentally induced foam cells with DSS extract. Then the antioxidative effect of DSS extract was compared with butylated hydroxyanisole (BHA). Result and Conclusions : Results obtained are as follows: 1. DSS extract showed significant antioxidative effect at 8 mg/ml or more. 2. DSS extract inhibited the formation of foam cells. 3. DSS extract inhibited the creation and revelation of conversion-related material about foam cells. 4. DSS extract prohibited the increase of smooth muscle of vessels.

• Fisheries and Aquatic Sciences
• /
• v.7 no.2
• /
• pp.76-83
• /
• 2004

To supply fresh and quality quarantined seafood in live seafood specialty restaurants, facilities for short-term culture or holding of live marine fish and shellfish are a necessity. In this study, the performance of a simple recirculating aquarium system for the culture and holding of marine fish was evaluated. The aquarium system consisted of a culture tank, a foam fractionator for solids removal, and a Styrofoam bead filter for nitrification and solids trapping. In the first trial, the aquarium was stocked with a total of 12 kg Korean rockfish, which were fed approximately $0.5\%$ of the total fish body weight daily. During the 2-month culture period, total ammonia nitrogen (TAN) and nitrite nitrogen $(NO_2-N)$ concentrations remained below 1mg/L and 2mg/L, respectively. The chemical oxygen demand (COD) fluctuated between 13.6 and 31.2 mg/L on selected sampling days. The total suspended solids (TSS) removed by the foam fractionator was between 2.7 and 4.6g daily. The Styrofoam bead filter not only reduced TAN and $NO_2-N$ in the culture tank water, but also trapped solids equivalent to 8.3-26.7\% of the weight of feed supplied. In Trial 2, 30kg of live fish were held in the aquarium without feeding for a 24-hour period and the water quality parameters were monitored. TAN and $NO_2-N$ concentrations first increased and then decreased to around 0.3mg/L. These results demonstrate that the recirculating aquarium system is a functional option for the short-term culture or holding of marine fish.

• Korean Journal of Food Science and Technology
• /
• v.30 no.4
• /
• pp.902-907
• /
• 1998

In this study the anaerobic degradation of nitrate by in GFM (gel and foam matrix) and bead gel immobilized Paracoccus denitrificans DSM 65 in continous culture was conducted. A novel GFM immobilization system was developed in order to improve conventional system (bead). With increasing nitrate concentration in water, the nitrate reduction rate was increased. The observed maximum denitrification rate by in GFM immobilized cells was 177 mg/L h in buffered water, while that was 33 mg/L h in tap water. In comparison with bead system the reduction activity by GFM system showed $1.2{\sim}2.1$ times better. The denitrification activity was not changed after 16 days storage at $5^{\circ}C$ and also showed better activity than that of free cells or even bead immobilized cells.

• Journal of Korea Foundry Society
• /
• v.37 no.6
• /
• pp.186-192
• /
• 2017

The lost foam casting method was used to fabricate Al-Si alloy thin sheet specimens; the effects of chemical composition and process variables on the mold filling and mechanical properties were investigated. The mold filling capability was observed to be proportional to the pouring temperature, and both the vibration imposed during the casting and the application of a pattern coating had rather negative effects. The mold filling capability also decreased with the addition of Mg or TiB. When the Mg content increased, the tensile strength of the cast alloy was enhanced, but the elongation decreased. However, after T6 heat treatment, both the strength and the elongation were improved. TiB addition for grain refining or pattern coating did not significantly affect the tensile properties.

• Journal of Microbiology and Biotechnology
• /
• v.6 no.2
• /
• pp.132-136
• /
• 1996

To investigate the characteristics of immobilized peppermint (Mentha piperita) cells, dry cell weight (DCW), change of cell viability, and oil productivity of the immobilized cells were determined. Peppermint cells were immobilized in polyurethane (PU) foams of $5{\times}5{\times}5$ mm and cultured in a shaking flask. The maximum DCW was 2.1 mg per foam piece after 20 days of cultivation and the cell density was approximately 420 mg per flask containing 200 foams in 200 ml medium. For the first five days of cultivation, the cell viability was about 80$%$ and decreased to 70$%$ during 5 to 20 days of cultivation. The maximum oil productivity, 148 mg/l was achieved after 40 days of cultivation. The immobilized cells were also cultivated in a bioreactor, equipped with a round spiral type impeller, containing 2, 400 PU foams. The cell viability after 30 days of cultivation with chitosan as an elicitor in the bioreactor was 67$%$ and DCW was 2.0 mg per foam piece. Though the cell viability was relatively high in the bioreactor system, the oil productivity was relatively lower than that of the flask system.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.11a
• /
• pp.107.2-107.2
• /
• 2007

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2006.11a
• /
• pp.33.2-33.2
• /
• 2006

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.05a
• /
• pp.48.1-48.1
• /
• 2008