• Advances in materials Research
• /
• v.2 no.1
• /
• pp.37-49
• /
• 2013

The transition metal salt doped solid polymer electrolyte [TSPE] were prepared with HPMC as a host polymer. The virgin and doped films were prepared by solution-casting method and investigated using wide angle X-ray scattering method. Micro structural parameters like lattice strain (g%), stacking/twin faults, the average number of unit cells counted in a direction perpendicular to the Bragg's plane (hkl) spacing of (hkl) planes dhkl, crystallite size Ds, distortion width, standard deviation were determined by whole pattern powder fitting (WPPF) method, which is an extension of single order method. It is found that the crystallite size decreases with the increase in the content of $FeCl_3$. This decrease is due to increase in localized breaking of polymer network which also accounts for the amorphous nature of the material. The filler inorganic salt $FeCl_3$ acts as plasticizer. FTIR study also confirms and justifies the interaction between the polymer and in-organic salt in the matrix. Physical properties like mechanical stability and Ac conductivity in these films are in conformity with the X-ray results.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.429-429
• /
• 2012

To investigate the gettering effect of B-doped n-type monocrystalline silicon wafer, we made the p-n junction by diffusing boron into n-type monocrystalline Si substrate and then oxidized the boron doped n-type monocrystalline silicon wafer by in-situ wet and dry oxidation. After oxidation, the minority carrier lifetime was measured by using microwave photoconductance and the sheet resistance by 4-point probe, respectively. The junction depth was analyzed by Secondary Ion Mass Spectrometry (SIMS). Boron diffusion reduced the metal impurities in the bulk of silicon wafer and increased the minority carrier lifetime. In the case of wet oxidation, the sheet resistance value of ${\sim}46{\Omega}/{\Box}$ was obtained at $900^{\circ}C$, depostion time 50 min, and drive-in time 10 min. Uniformity was ~7% at $925^{\circ}C$, deposition time 30 min, and drive-in time 10 min. Finally, the minority carrier lifetime was shown to be increased from $3.3{\mu}s$ for bare wafer to $21.6{\mu}s$ for $900^{\circ}C$, deposition 40 min, and drive-in 10 min condition. In the case of dry oxidation, for the condition of 50 min deposition, 10 min drive-in, and O2 flow of 2000 SCCM, the minority carrier lifetime of 16.3us, the sheet resistance of ${\sim}48{\Omega}/{\Box}$, and uniformity of 2% were measured.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1257-1262
• /
• 2008

A long-distance remote sensing of temperature and current based on a fiber Bragg grating (FBG) is proposed and demonstrated. The thermal expanding effect of the epoxy and the Er-doped fiber ring laser (EFRL) are applied to the sensor system to enhance the temperature and current sensitivity. An EFRL with a 5 km-single-mode fiber and a FBG shows a high extinction ratio of more than 60 dB and a low power fluctuation of less than 1 dB. The metal wires are used to supply the current to the sensors. When the NOA65 puts on the FBG as a thermal expanding material, the temperature and current sensitivity of the lasing wavelength shift are about $30\;pm/^{\circ}C$ and 3pm/mA, respectively. The proposed sensing scheme is useful for measurement of current or temperature at a distant object of more than several km.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.5
• /
• pp.102-107
• /
• 2012

Halogen lamp was applied to fabricate the selective emitter crystalline silicon solar cell. In selective emitter structure, the recombination of minority carriers is reduced with heavily doped emitter under metal grid, consequently improving the conversion efficiency. Laser selective emitter process which is recently used the most generally induces the damage on the silicon surface. However the lamp has enough heat to form heavily doped emitter layer by diffusing phosphorus from PSG without surface damage. In this work, we have studied to find the design and the suitable condition for halogen lamp such as power, time, temperature and figured out the possibility to fabricate the selective emitter silicon solar cell by lamp heating. The sheet resistance with $100{\Omega}/{\Box}$ was lower to $50{\Omega}/{\Box}$ after halogen lamp treatment. Heat transfer to lightly doped emitter region was blocked by using the shadow mask.

• Journal of the Korean Ceramic Society
• /
• v.44 no.8
• /
• pp.403-406
• /
• 2007

Ferroelectric Ce-doped $Bi_4Ti_3O_{12}$ (BCT) thin films were deposited by liquid delivery metal organic chemical vapor deposition (MOCVD) onto a $Pt(111)/Ti/SiO_2/Si(100)$ substrate. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to identify the crystal structure, the surface, and the cross-section morphology of the deposited ferroelectric flims. After annealing above $640^{\circ}C$, the BCT films exhibited a polycrystalline structure with preferred (001) and (117) orientations. The BCT lam capacitor with a top Pt electrode showed a large remnant polarization ($2P_r$) of $44.56{\mu}C/cm^2$ at an applied voltage of 5 V and exhibited fatigue-free behavior up to $1.0{\times}10^{11}$ switching cycles at a frequency of 1 MHz. This study clearly reveals that BCT thin film has potential for application in non-volatile ferroelectric random access memories and dynamic random access memories.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.1-6
• /
• 2006

High performance $Si_{0.8}Ge_{0.2}$ heterostructure metal-oxide-semiconductor field effect transistors (MOSFETs) were fabricated using well-controlled delta-doping of boron and $Si_{0.8}Ge_{0.2}$/Si heterostructure epitaxal layers grown by reduced pressure chemical vapor deposition. In this paper, we report 1/f noise characteristics of the SiGe pMOSFETs measured under various bias conditions of the gate and drain voltages changing in linear operation regions. From the noise spectral density, we found that the gate and drain voltage dependence of the noise represented same features, as usually scaled with $f^{-1}$ However, 1/f noise was found to be much lower in the device with boron delta-doped layer, by a factor of $10^{-1}_10^{-2}$ in comparison with the device fabricated without delta-doped layer. 1/f noise property of delta-doped device looks important because the device may replace bipolar transistors most commonly embedded in high-frequency oscillator circuits.

• Solar Energy
• /
• v.17 no.3
• /
• pp.51-57
• /
• 1997

Cu-doped ZnTe thin films have been grown by hot-wall evaporation. The electrical conductivity of the intrinsic ZnTe film was of p-type and as low as $10^{-6}({\Omega}{\cdot}cm)^{-1}$. As the doped Cu concentration was increased, the electrical conductivity was increased. up to $10^2({\Omega}{\cdot}cm)^{-1}$, but the mobility was decreased a little. The heavily doped sample shows the metal-like electrical resistivity.

• Current Photovoltaic Research
• /
• v.8 no.2
• /
• pp.60-65
• /
• 2020

In perovskite solar cells with planar heterojunction configuration, selection of proper charge-transporting layers is very important to achieve stable and efficient device. Here, we developed solution processible Cu doped NiO_x (Cu:NiO_x) thin film as a hole-transporting layer (HTL) in p-i-n structured methylammonium lead trihalide (MAPbI₃) perovskite solar cell. The transmittance and thickness of NiO_x HTL is optimized by control the spin-coating rate and Cu is additionally doped to improve the surface morphology of undoped NiO_x thin film and hole-extraction properties. Consequently, a perovskite solar cell containing Cu:NiO_x HTL with optimal doping ratio of Cu exhibits a power conversion efficiency of 14.6%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.460-463
• /
• 2002

$MoO_3$ thin films were deposited on electrode and heater screen-printed alumina substrates in $O_2$ atmosphere by RF reactive sputtering using Molybdenum metal target. The deposition was performed at $300^{\circ}C$ with 350W of a forward power in an $Ar-O_2$ atmosphere. The working pressure was maintained at $3{\times}10^{-2}mtorr$ and all deposited films were annealed at $500^{\circ}C$ for 5hours. To investigate gas sensing characteristics of the addition doped $MoO_3$ thin film, Co, Ni and Pt were used as adding dopants. The sensing properties were investigated in tenn of gas concentration under exposure of reducing gases such as $H_2$, $NH_3$ and CO at optimum working temperature. Co-doped $MoO_3$ thin film shows the maximum 46.8% of sensitivity in $NH_3$ and Ni-doped $MoO_3$ thin film exhibits 49.7% of sensitivity in $H_2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.705-710
• /
• 2003

MoO$_3$thin films were deposited on electrode of alumina substrates in $O_2$atmosphere by RF reactive sputtering using molybdenum metal target. The deposition was performed at 30$0^{\circ}C$ with 350 W of a forward power in an Ar-O$_2$atmosphere. The working pressure was maintained at 3$\times$10$^{-2}$ torr and all deposited films were annealed at 50$0^{\circ}C$ for 5 hours. The surface morphology of films was observed by using a SEM and crystalline phases were analyzed by using a XRD. To investigate gas sensing characteristics of the doped MoO$_3$thin film, Co, Ni and Pt were used as dopants. The sensing properties were investigated in term of gas concentration under exposure of reducing gases such as H$_2$, NH$_3$and CO at optimum working temperature. Co-doped MoO3 thin film shows the maximum 46.8 % of sensitivity in NH$_3$ and Ni-doped MoO$_3$thin film exhibits 49.7 % of sensitivity in H$_2$.