• Transactions of Materials Processing
• /
• v.12 no.4
• /
• pp.401-407
• /
• 2003

This paper newly proposes a mesh regularization method for the enhancement of the efficiency in sheet metal forming analysis. The regularization method searches for distorted elements with appropriate searching criteria and constructs patches including the elements to be modified. Each patch is then extended to a three-dimensional surface in order to obtain the information of the continuous coordinates. In constructing the surface enclosing each patch, NURBS(Non-Uniform Rational B-Spline) surface is employed to describe a three-dimensional free surface. On the basis of the constructed surface, each node is properly arranged to form unit elements as close as to a square. The state variables calculated from its original mesh geometry are mapped into the new mesh geometry for the next stage or incremental step of a forming analysis. The analysis results with the proposed method are compared to the results from the direct forming analysis without mesh regularization in order to confirm the validity of the method.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.1 no.1
• /
• pp.82-88
• /
• 1991

Determination of Cu, Fe, Ni, Pb, and Zn concentrations in coal and respirable coal dust were performed by atomic absorption spectrophotometry. The coal samples of 18 coal mines in Gangneung area were collected and 25 coal mines in Taebaek area. Crushed coal samples were divided into three mesh sizes. The results were as follows : 1. Metal concentrations of coals in Gangneung area by sieve sizes( -100/+200 mesh, -200/+325 mesh, -325 mesh) were as follows: Cu ; 20, 18, 19, Fe ; 1,830, 1,765, 1,107, Pb ; 6, 8, 14, Ni ; 17, 17, 14, Zn ; 4, 2, $4{\mu}g/g$, respectively. Metal concentrations in coals in Taebaek area by sieve sizes(-100/+200 mesh, -200/+325 mesh, -325 mesh) were as follows: Cu ; 30, 32, 26, Fe ; 1,741, 1,822, 1,773, Pb ; 8, 9, 7, Ni ; 13, 13, 13, Zn ; 8, 5, $4{\mu}g/g$, respectively. There were not significant differences of Cu, Fe, Ni, Pb, and Zn concentrations of coals statistically in Gangneung and Taebaek area by sieve size. 2. Metal concentrations of coals in Gangneung and Taeback area were as follows : Cu ; 19, 30, Fe ; 1,514, 1,778, Pb ; 9, 8, Ni ; 16, 13, Zn ; 3, $6{\mu}g/g$, respectively. Differences of copper and zinc concentrations of coal samples were significant between Gangneung and Taebaek area, but those of iron, nickel and lead concentrations were not significant. 3. Copper, iron, lead, nickel and zinc concentrations of coals and respirable coal dust were as follows : Cu ; 30, 6, Fe ; 1,779, 5,075, Pb ; 8, 7,814, Ni ; 13, 5,681, Zn ; 5, $134{\mu}g/g$, respectively. Differences of nickel, lead and zinc concentrations were significant between coals and respirable coal dust but those of copper and iron concentrations were not significant.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.04a
• /
• pp.105-112
• /
• 2002

A new grid-based approach is presented for automatic generation of hexahedral meshes for simulation of plastic deformation in metal forming. In this approach, special enveloping schemes are applied, to eradicate the sources of the degenerate elements that may appear in a generated mesh. The schemes are described in detail, along with a complete procedure for mesh generation. The capability of the approach to deal with an arbitrary, 3-D process geometry is demonstrated through application to a selected forming problem.

• Current Photovoltaic Research
• /
• v.2 no.3
• /
• pp.79-83
• /
• 2014

Dye-sensitized solar cells (DSSCs) are applied in the emerging fields of building integrated photovoltaic and electronics integrated photovoltaic like small portable power sources as demands are increased with characteristic advantages. Highly flexible dye-sensitized solar cells (DSSCs) prepared on single stainless steel mesh were proposed in this paper. Single mesh DSSCs structure utilizing the spraying the chopped glass paper on the surface treated stainless steel mesh for integrating the space element and the electrode components, counter electrode component and photoelectrode component were coated on each side of the single mesh. The fabricated single mesh DSSCs showed the energy-conversion efficiency 0.50% which show highly bendable ability. The new single mesh DSSCs may have potential applications as highly bendable solar cells to overcome the limitations of TCO-based DSSCs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.313-313
• /
• 2016

Transparent conductive oxide (TCO) films have many disadvantages, such as rarity, possible exhaustion, process temperature limitations, and brittleness on a flexible substrate. In particular, as display technology moves toward flexible displays, TCO will become completely unsuitable due to its brittleness. To address theses issue, many researchers have been studying TCO substitutes. In recent efforts, metal nanowires, conducting polymers, carbon nanotube networks, graphene films, hybrid thin films, and metal meshes/grids have been evaluated as candidates to replace TCO electrodes. In this study, we fabricated the TCO film with Ag meshes shape using polystyrene (PS) beads monolayer on the substrate. The PS beads were used as a template to create the mesh pattern. We fabricated the monolayer on the flexible substrate (PES) with the well-aligned PS beads. Electrodes with Ag mesh shape were formed using this patterned monolayer. We could fabricated the Ag mesh electrode with the sheet resistance with $8ohm{\Omega}/{\Box}$.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.4
• /
• pp.327-336
• /
• 2013

This study aimed to investigate the reinforcing effect of two kinds of glass fiber, Quarts Splint$^{TM}$ Mesh and SES MESH$^{(R)}$ and to evaluate the effect of the thermocycling on the transverse strength of the denture base and on the reinforcing effect of the reinforcements. 20 specimens of the size of $2.5{\times}10.0{\times}65.0mm$ were fabricated for each group; control group, metal mesh reinforcement group, Quarts Splint$^{TM}$ Mesh reinforcement group and SES MESH$^{(R)}$ reinforcement group. To find the difference made by the thermocycling, 10 specimens of each reinforcement group were treated by thermocycling. 3-point bending test was performed to measure the transverse strength of the denture base resin. The specimens reinforced with SES MESH$^{(R)}$ and Quarts Splint$^{TM}$ Mesh showed significantly higher transverse strength than the control group (P<.05), and significantly lower transverse strength than the specimens reinforced with the metal mesh (P<.05). Thermocycled specimens were lower in transverse strength than non-thermocycled specimens in the control group, metal mesh group, Quarts Splint$^{TM}$ Mesh group and SES MESH$^{(R)}$ group, however significant difference (P<.05) was found only in the control group.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2000.11a
• /
• pp.39-39
• /
• 2000

• Journal of Powder Materials
• /
• v.24 no.6
• /
• pp.464-471
• /
• 2017

A metal mesh TCE film is fabricated using a series of processes such as UV imprinting of a transparent trench pattern (with a width of $2-5{\mu}m$) onto a PET film, filling it with silver paste, wiping of the surface, and heat-curing the silver paste. In this work nanosized (40-50 nm) silver particles are synthesized and mixed with submicron (250-300 nm)-sized silver particles to prepare silver paste for the fabrication of metal mesh-type TCE films. The filling of these silver pastes into the patterned trench layer is examined using a specially designed filling machine and the rheological testing of the silver pastes. The wiping of the trench layer surface to remove any residual silver paste or particles is tested with various mixture solvents, and ethyl cellosolve acetate (ECA):DI water = 90:10 wt% is found to give the best result. The silver paste with 40-50 nm Ag:250-300 nm Ag in a 10:90 wt% mixture gives the highest electrical conductance. The metal mesh TCE film obtained with this silver paste in an optimized process exhibits a light transmittance of 90.4% and haze at 1.2%, which is suitable for TSP application.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.2
• /
• pp.363-372
• /
• 1996

A common site of fracture in maxillary complete denture is on the anteroposterior midline that coincides with the notch for relief of the labial frenum. Various approaches to reduce the incidence of this type of fracture have been suggested. The most widely used technique is the reinforcement of acrylic resin denture base with several solid metal forms. But few comparative studies on the efficacy of metal reinforcements have been reported. This study was conducted to compare reinforcing effects of commonly available metal reinforcements, which include wire, metal mesh embedded in the denture base and metal plate affixed to the impression surface of denture base by silicoating technique. This was load on the posterior. The strain gauges were oriented perpendicular to the anteroposterior midline of maxillary polished denture surface at one labial and the four palatal sites Non-renforced denture was used as control. The results were as follows : 1. In the non-reinforced denture group, only tensile strains on the palatal polished surface were observed. The tensile strains decreased in the order of incisive papilla, posterior denture border area, mid palatal area and rugae area. Compressive strain was observed on the labial polished surface. 2. As compared with the non-reinforced denture group, the metal plate or the metal mesh reinforced denture groups showed reduced palatal tensile strains,and the metal mesh reinforcement had a better reinforcing effect than the metal plate. But both reinforced denture groups showed no difference in the amount of compressive strain on the labial polished surface when compared to the non-reinforced denture group. 3. The metal wire positioned just above the labial notch decreased the compressive strain on the labial polished surface. But the presence of metal wires in the palatal polished surface caused increase in tensile strains in the area.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.150-150
• /
• 2010

Carbon nanotubes have drawn attention as one of the most promising emitter materials ever known not only due to their nanometer-scale radius of curvature at tip and extremely high aspect ratios but also due to their strong mechanical strength, excellent thermal conductivity, good chemical stability, etc. Some applications of CNTs as emitters, such as X-ray tubes and microwave amplifiers, require high current emission over a small emitter area. The field emission for high current density often damages CNT emitters by Joule heating, field evaporation, or electrostatic interaction. In order to endure the high current density emission, CNT emitters should be optimally fabricated in terms of material properties and morphological aspects: highly crystalline CNT materials, low gas emission during electron emission in vacuum, optimal emitter distribution density, optimal aspect ratio of emitters, uniform emitter height, strong emitter adhesion onto a substrate, etc. We attempted a novel approach to fabricate CNT emitters to meet some of requirements described above, including highly crystalline CNT materials, low gas emission, and strong emitter adhesion. In this study, CNT emitters were fabricated by filtrating an aqueous suspension of highly crystalline thin multiwalled CNTs (Hanwha Nanotech Inc.) through a metal mesh. The metal mesh served as a support and fixture frame of CNT emitters. When 5 ml of the CNT suspension was engaged in filtration through a 400 mesh, the CNT layers were formed to be as thick as the mesh at the mesh openings. The CNT emitter sample of $1{\times}1\;cm^2$ in size was characteristic of the turn-on electrical field of 2.7 V/${\mu}m$ and the current density of 14.5 mA at 5.8 V/${\mu}m$ without noticeable deterioration of emitters. This study seems to provide a novel fabrication route to simply produce small-size CNT emitters for high current emission with reliability.