• 태양에너지
• /
• 제16권2호
• /
• pp.113-122
• /
• 1996

본 연구는 수직원통형 빙축열조 내에 상변화물질로서 순수한 물을 $-10^{\circ}C$의 초기 과냉온도로 응고시킨 후, 작동유체의 입구온도를 $7^{\circ}C,\;4^{\circ}C,\;1^{\circ}C$로, 작동유체의 유입방향을 상향과 하향으로 각각 변화시키면서 외향용융시켰을 경우, 시간경과에 따른 축열매질의 온도분포, 상경계면의 형상, 용융율, 용융에너지를 실험적으로 구하여 이를 비교 검토한 것이다. 작동유체의 입구온도가 $7^{\circ}C,\;4^{\circ}C$의 경우에는 작동유체의 유입방향이 상 하향 모두 물의 최대 밀도점인 $4^{\circ}C$ 부근에서 일시적으로 온도가 상승하지 않고 일정 시간동안 정체하는 온도정체구간이 나타났다. 또한, 용융이 진행됨에 따라 물이 축열조의 하부에 적체되고, 이에 따라 하부에서의 용융이 활발히 진행됨으로써 상경계면 형상은 전체적으로 종모양 형태의 곡선을 나타낸다. 작동 유체의 입구온도가 $7^{\circ}C$인 경우, 용융율(Vl/Vtot)과 용융에너지는 작동유체의 유입방향이 상향인 경우가 하향인 경우에서보다 크게 나타난 반면, 작동유체의 입구온도가 $4^{\circ}C,\;1^{\circ}C$인 경우는 $7^{\circ}C$의 경우와는 달리 하향인 경우가 상향인 경우에서보다 큰 것으로 나타났다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 추계 학술논문 발표대회
• /
• pp.45-46
• /
• 2015

Recently, the large amount of sulfur is globally generated by the development of the petroleum refining industry every year. In this study, without the use of the sulfur with a high melting point used in the previous studies, the modified sulfur mortar with addition of a melting point of about 65℃ were tested to determine their distribution and strength properties according to the mixing method and curing conditions. This study is a test to find out the Density, Absorption and Table Flow of the modified sulfur and general sulfur. As result, general industrial sulfur flow was lower, showed a high absorption rate.

• 한국의류학회지
• /
• 제11권3호
• /
• pp.33-40
• /
• 1987

PET FDY was heat set at various temperatures and times and the microstructural changes was investigated through crystallinity, birefringence and melting behavior analyses. Crystallinity of heat set PET increased as the treatment temperature and time increased. Birefringence also increased as temperature and time increased. The melting behavior of heat set PET was as follows: In most cases, PET showed double melting peaks. As temperature and time increased, form II crystal became sharp and increased in size, and form I crystal decreased in size. The slower the heating rate, the higher the programmed heating effect during DSC analysis.

• 한국연소학회지
• /
• 제10권1호
• /
• pp.27-36
• /
• 2005

In this study, we investigated characteristics of a gas flow and a combustion property during the combustion of a RDF in a pyrolysis melting incinerator with disposal rate of 30 kg/hr. The RDF was pyrolyzed through the pyrolysis chamber at $600^{\circ}C$ of the chamber surface without oxygen condition. The pyrolysis gas was injected in the combustion chamber. It was burned by means of the staged combustion that was injecting secondary and tertiary air in the combustor. We measured the temperatures and the gas components in the combustion chamber while maintaining the air-fuel ratio of 1.3. Finally, we confirm that additional air injection, secondary and tertiary air ratio, was the most important factor to reduce NOx.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.235-240
• /
• 2001

This study presents experimental work on phase change heat transfer, in order to increase heat transfer rate, ultrasonic vibrations were introduced. Solid-liquid phase change occurs in a number of situations of practical interest. This study reveal that ultrasonic vibrations accompany the effects like agitation, acoustic streaming, cavitation, and oscillating fluid motion. Such effects are a prime mechanism in the overall melting process when ultrasonic vibrations are applied. Some common examples include the melting of edible oil, metallurgical process such as casting and welding, and materials science applications such as crystal growth. Therefore, this study presented the effective way to enhance phase change heat transfer.

• 한국생산제조학회지
• /
• 제21권3호
• /
• pp.493-501
• /
• 2012

A rotational force generator for molten metal is developed using a linear motor design technology. Also, the developed device is applied to reproduce aluminum scraps and easy to control the rotate, stop, and forward and reverse rotation of molten metal. In addition, the developed device improves the melting speed and reproduction rate about 250 (%) and 96-99 (%), respectively, compared to the conventional handmade methods. Because it generates almost no dusts, it can improve working environments in a factory. Also, it has no losses in energy because it directly melts scraps. The device generates small amounts of the loss in refractory materials and aluminum caused by its oxidation because the molten metal is continuously rotated in which the loss and oxidized aluminum are the problems in the conventional melting and holding furnaces. Thus, it is possible to extend the life of furnaces and to produce high quality aluminum products.

• 대한기계학회논문집
• /
• 제19권10호
• /
• pp.2595-2606
• /
• 1995

Buoyancy-assisted melting of an unconstrained ice in an isothermally heated horizontal enclosure was numerically analyzed in a range of wall temperatures encompassing the density inversion point. The problem as posed here involves two physically distinct domains each of which has its own scales and respective heat transfer mode. These two domains join at the junction where the liquid squeezed out of the film region flushes into the lower melt pool. Both of these domains have been treated separately in the literature by a patching technique which invokes several, otherwise unnecessary, assumptions. The present study eliminates successfully such a superfluous procedure by treating the film and lower melt pool regions as a single domain. As a result of this efficient solution procedure, the interaction of the water stream ejected at the junction and the natural convection in the melt pool could be clarified for different wall temperatures. Though limited by two-dimensionality, the present results conformed indirectly the earlier reported transition of the flow pattern, as the wall temperature was increased over the density inversion point. The transient evolution of the melting surface, the time rate of change in melt volume fraction, the local and temporal variation of the heat transfer coefficients are analyzed and presented.

• Nuclear Engineering and Technology
• /
• 제48권2호
• /
• pp.448-456
• /
• 2016

Severe accident scenarios in nuclear reactors, such as nuclear meltdown, reveal that an extremely hot molten core may fall into the nuclear reactor cavity and seriously affect the safety of the nuclear containment vessel due to the chain reaction caused by the reaction between the molten core and concrete. This paper reports on research focused on the type and amount of vapor produced during the reaction between a high-temperature molten core and concrete, as well as on the erosion rate of concrete and the heat transfer characteristics at its vicinity. This study identifies themass fraction and melting temperature as the most influential properties of concrete necessary for a safety analysis conducted in relation to the thermal interaction between the molten core and the basemat concrete. The types of concrete that are actually used in nuclear reactor cavities were investigated. The $H_2O$ content in concrete required for the computation of the relative amount of gases generated by the chemical reaction of the vapor, the quantity of $CO_2$ necessary for computing the cooling speed of the molten core, and the melting temperature of concrete are evaluated experimentally for the molten core-concrete interaction analysis.

• 설비공학논문집
• /
• 제25권9호
• /
• pp.477-483
• /
• 2013

A numerical analysis of solid-liquid phase change was performed on a heat transfer module which consisted of circulating water path (BRINE), heat transfer plate (HTP) and phase change material (PCM) layers, such as high temperature PCM (HPCM, $78{\sim}79^{\circ}C$) and low temperature PCM (LPCM, $28{\sim}29^{\circ}C$). There were five arrangements, consisting of BRINE, HTP, LPCM and HPCM layers in the heat transfer module. The time and heat transfer rate for melting/solidification was compared to their arrangements, against each other. As results, the numerical time without convection was longer than the experimental one for melting/solidification. Moreover, the melting/solidification with the BRINE I-LPCM-BRINE II-HPCM arrangement was faster(10 hours) than the others; HPCM-BRINE-LPCM, BRINE I-HPCM-LPCM-BRINE II one.

• 한국주조공학회지
• /
• 제43권5호
• /
• pp.223-229
• /
• 2023

In this study, STS316L produced by a double-melting process involving vacuum induction melting (VIM) and vacuum arc remelting (VAR) was subjected to extrusion and drawing to form a tube and was subsequently electrolytic polished (EP). The grain size of the obtained STS316L without EP was approximately 55 ㎛, with no difference found after EP. The thickness of the EP layer was measured by AES and TEM, showing values of approximately 10 nm and 15 nm, respectively. After EP, the Cr/Fe and CrO/FeO ratios of the passive layer increased from 1.48 to 1.62 and from 2.15 to 2.26, respectively, while the surface roughness decreased significantly from 0.255 to 0.024 ㎛. Consequently, the corrosion rate decreased in both NaCl and HCl solutions after the EP process. Additionally, the amounts of eluted Cr and Fe ions were reduced from 1.2 to 0.8 ppb and 10.3 to 0.8 ppb, respectively. Furthermore, polarization tests revealed that STS316L treated with EP required a lower current density to reach a passive state, indicating that corrosion behavior was retarded.