• 한국결정성장학회지
• /
• 제8권4호
• /
• pp.655-659
• /
• 1998

과냉각된 melt-spun $Nd_{14.73}Fe_{78.67}B_{6.60}$리본의 급속응고속도 및 열처리에 따른 보자력의 변화를 조사하였으며, 이 결과를 분석하기 위하여 비정질로 부터의 결정화 거동을 연구하였다. 리본 제조시 급속응고속도가 증가함에 따라 결정화 후의 고유 보자력은 감소하였다. $Nd_{14.73}Fe_{78.67}B_{6.60}$ 비정질은 안정한 $Nd_2Fe_{14}B$ 상으로 결정화하는 과정에서 $\alpha$-Fe와 $Fe_3B$ 상이 생성된다. $Fe_3B$ 상은 $Nd_2Fe_{14}B$ 상이 결정화됨과 동시에 사라지나 $\alpha$-Fe 상은 완전히 결정화된 이후에도 기지상인 $Nd_2Fe_{14}B$ 상과 함께 잔류한다. 열처리된 리본내에 잔류하는 연자성상인 $\alpha$-Fe에 의해 고유 보자력의 특성이 저하하였다.

• Journal of Ceramic Processing Research
• /
• 제20권3호
• /
• pp.276-279
• /
• 2019

New green-emitting Sr4ScAl3O10:Eu2+ phosphor was prepared using a novel melt quenching synthesis method. The temperature of raw materials irradiated with the strong light of the Xe arc-lamp was rose up to about 2273 K, followed by a sharp drop in the temperature after turn off the lamp. This method is a useful tool for rapid screening of novel phosphor materials.

• Nuclear Engineering and Technology
• /
• 제38권1호
• /
• pp.1-10
• /
• 2006

The interaction and mixing of high-temperature melt and water is the important technical issue in the safety assessment of water-cooled reactors to achieve ultimate core coolability. For specific advanced light water reactor (ALWR) designs, deliberate mixing of the core-melt and water is being considered as a mitigative measure, to assure ex-vessel core coolability. The paper provides the background of past experiments as well as key fundamentals that are needed for melt-water interfacial transport phenomena, thus enabling the development of innovative safety technologies for advanced LWRs that will assure ex-vessel core coolability.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2017년도 임시총회 및 하계학술연구발표회
• /
• pp.119-120
• /
• 2017

• Nuclear Engineering and Technology
• /
• 제41권5호
• /
• pp.575-602
• /
• 2009

In the wake of the Three Mile Island accident, vigorous research efforts were initiated to acquire a basic knowledge of the progression and consequences of accidents that involve a substantial degree of core degradation and melting. The primary emphasis of this research was placed on containment integrity, with: i) hydrogen combustion-detonation, ii) steam explosion, iii) direct containment heating (DCH), and iv) melt attack on the BWR Mark-I containment shell identified as energetic processes that could lead to early containment failure (i.e., within the first 24 hours of the accident). Should the core melt fail the reactor vessel, then non-condensable gas production from Molten Core-Concrete Interaction (MCCI) was identified as a mechanism that could fail the containment by pressurization over the long term. One signification question that arose as part of this investigation was the effectiveness of water in terminating an MCCI by flooding the interacting masses from above, thereby quenching the molten core debris and rendering it permanently coolable. Successful quenching of the core melt would prevent basemat melt through, as well as continued containment pressurization by non-condensable gas production, and so the accident progression would be successfully terminated without release of radioactivity to the environment. Based on these potential merits, ex-vessel corium coolability has been the focus of extensive research over the last 20 years as a potential accident management strategy for current plants. In addition, outcomes from this research have impacted the accident management strategies for the Gen III+LWR plant designs that are currently being deployed around the world. This paper provides: i) an historical overview of corium coolability research, ii) summarizes the current status of research in this area, and iii) highlights trends in severe accident management strategies that have evolved based on the findings from this work.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1365-1372
• /
• 2001

In the planar flow casting(PFC) process, the conditions of the melt puddle between nozzle and rotating wheel affect significantly the quality and dimensional uniformity of the downstream ribbon. For stable puddle formation, the nozzle is placed very close to the quenching wheel, so the surface-tension and wall-adhesion forces have an important effect upon the fluid flow.\`In this study the planar flow casting process has been mode]ed using the VOF method for free surface tracking. The transient puddle formation from the present analysis shows good agreements with the previous experimental results. Furthermore, the variation of melt temperature and the corresponding cooling rate of the melt have been examined. The present results also show how the melt puddle can be farmed on the rotating substrate, how the melt flows within the puddle, and how the changes of the process variables affect the puddle formation and its corresponding fluid flow and heat transfer behavior.

• 수산해양기술연구
• /
• 제31권3호
• /
• pp.279-286
• /
• 1995

As Al-Li based alloys are to find widespread use in aerospace and other structural applications in which their low-density high specific stiffness properties be exploited, their mechanical properties must adequately match those of the which they intended to replace. In order to develop these purposed, the precipitation behaviors of the rapidly solidified Al-Li-Ti alloys aged at various temperature were investigated. ${\delta}'$ phase precipitated homogeneously in the matrix during not only melt quenching but also aging at the aging temperature of $160^{\circ}C\;and\;210^{\circ}C$. The addition of the Ti in Al-Li alloy promoted the formation of $\delta$' phase. The addition of Ti on the ${\delta}'$ solvus line had a little effect over the thermodynamics ${\delta}'$ solvus line. The reason for these behavior was that the ${\delta}'$ phase was suppressed to precipitate as much as supercooling by melt quenching. The discontinuous precipitation reaction occurred by the preferential growth of ${\delta}'$ phase due to the migration of grain boundary provided the driving force dependent of solute concentration fluctuations.

• Elastomers and Composites
• /
• 제36권3호
• /
• pp.177-187
• /
• 2001

폴리프로필렌(PP)/폴리우레탄(PU) 블렌드를 compositional quenching으로 제조하여 모폴로지, 인장물성, 표면에너지 그리고 열안정성 등을 조사하였다. 블렌드 제조시, 말레인산 무수물이 그라프트된 PP(MPP)와 히드록시에틸 말레이미드가 그라프트된 PP(HPP)를 반응성 상용화제로 도입하였으며, 이들의 생성 및 PU 조성과의 반응을 FT-IR로 확인하였다. Compositional quenching으로 제조한 블렌드는 용융블렌드에 비해 높은 혼화성을 보였으며, 블렌드내의 상용화제의 함량이 증가함에 따라 모폴로지, 인장물성. 표면특성, 그리고 열안정성 등의 물성이 현저하게 향상되었다. 상용화제로 MPP를 도입한 블렌드는 HPP를 도입한 블렌드에 비해, 높은 표면 에너지를 가졌다.

• 열처리공학회지
• /
• 제9권1호
• /
• pp.19-26
• /
• 1996

Melt-quenching of steels leads to various metallographic effects such as refinement of grain size, extension of the solid solubility of carbon and alloying elements, and is expected to improve the mechanical properties of conventional steels. Furthermore, this technique is a useful method for producing sheet directly from liquid state. And it will lend itself to development as a continuous cast process which offers significant savings in energy and product costs. The purpose of this study is to present the microstructures of melt-quenched austenitic stainless steels. As the results of this study, the morphology of melt-quenched microstructure show that the roll contact area is columnar structure, and the free surface area is dendrite structure. As the line speed increases, the ratio of $d_{colunnar}/d_{total}$ increases from 0.12 to 0.60, but the ribbon thickness decreases from $150{\mu}m$ to $30{\mu}m$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.439-442
• /
• 2001

Chalcogenide glassy semiconductors(CGS) can be obtained by the melt quenching technique. We have investigated the thin film heterostructures : metal-chalcogenide glassy semiconductors, where metal is copper, and chalcogenide glassy semiconductors are glasses of the system As-Se. CU/CGS film heterostructure were produced in the vacuum evaporator by the method of vacuum thermal evaporation. Doped films are very sensitive to external actions, and this property allows developing supersensitive precision sensors of temperature, humidity, illumination, and etc. based on them. Cu/CGS film has shown that resistance strongly depend on the temperature. The ratio of resistance vs. temperature has shown over a 2 k$\Omega$/degree. The slop of temperature and resistance shows linear.