• Computers and Concrete
• /
• 제31권5호
• /
• pp.395-403
• /
• 2023

The paper investigates the effect of two parameters - sand content (SC) and grain migration during shearing - on the mechanical properties of gravel-sand mixtures. Consolidated undrained (CU) triaxial tests were carried out on eight series of mixtures containing gravel (1<d<16 mm) and sand (0.1<d<1 mm). The prepared mixtures have sand contents of 0, 10, 15, 20, 40, 54, 94 and 100%, and a relative density of 60%. The transition sand content (TSC) is experimentally defined and marks the transition from gravel-driven to sand-driven behavior. For SC<TSC, the dry density of the mixture increases with SC. This induces an increase in undrained peak strength and dilative trend. The slope and position of the critical state line (CSL) are also deeply dependent on SC. At SC=TSC, the mixtures exhibit the largest dry density and yield the highest undrained peak strength and the largest dilative trend. During shearing, large internal migration of grains was observed at the TSC, causing heterogeneity in the sample. Analysis of the CSL deduced from the final points of the triaxial tests shows that, at the TSC, failure appears to correspond to the behavior of the coarsest fraction of the soil. This fraction is located in the upper part of the sample, where the sand particles had been eliminated by suffusion. On the other hand, in the more stable materials, the CSL is consistent with the bulk grain size distribution of the soil.

• 한국의류학회지
• /
• 제13권1호
• /
• pp.79-87
• /
• 1989

In the part 1 and 2, relations were found between fundmental mechanical properties and primary hand values, performance of Korean women's summer and fall & winter fabrics. In this paper, in order to investigate the hand values and mechanical properties such as tensile, shearing, bending, compression, surface and thickness & weight of the core-spun yarn woven fabrics for Korean folk clothes were measured by KES-F system. The experimental results are statistically analyzed in the aspects of the mechanical properties, their effects on the hand values, formation of weared clothes and transformation behavior. The correlation in the hand values are analyzed, too. Furthermore, there mechanical properties are discussed in comparison with those values for kimono fabrics. The main results are summarized as follows: 1. The core-spun yarn woven fabrics for Korean folk clothes have box-shaped silhouette based on higher bending rigidity and shear elasticity. 2. The core-spun yarn woven fabrics for Korean folk clothes are inferior to silk fabrics, superior to polyester fabrics in formation. 3. A drapability and wrinkle recovery of core-spun yarn woven fabrics for Korean folk clothes formation for weared clothes are inferior to polyester fabrics, superior to silk fabrics. 4. A primary factor of mechanical properties contribute to the hand values of core-spun yarn woven fabrics for Korean folk clothes are same as the Korean women's winter fabrics, except for flexibility with soft feeling. 5. As for the hand values of core-spun yarn woven fabrics for Korean folk clothes, stiffness, anti-drape stiffness are superior to those of polyester fabrics. And also, flexibility with soft feeling, scrooping feeling of core-spun yarn woven fabrics have greater values as compared with silk fabrics for Korean folk clothes.

• 대한기계학회논문집A
• /
• 제37권1호
• /
• pp.67-75
• /
• 2013

핵연료 지지격자 소재로 사용되는 zircaloy-4의 유동응력을 Johnson-Cook 모델로 결정하고, 모델의 재료상수를 역 공학으로 도출했다. 변형률 항의 상수 A, B, n과 변형률 속도 항의 $\dot{\varepsilon}_0$은 인장시험을 통해 결정했다. 상수 C, m을 역 공학으로 도출하기 위해 슬롯밀링시험을 수행하고, 유한요소해석으로 모사했다. 실험과 해석으로 얻은 결과의 차이를 오차함수, 즉 최소화 대상 목적함수로 설정했고, 이 함수를 최소로 하는 C, m을 도출했다. 도출한 상수의 타당성을 검증하기 위해 상관계수를 살펴봤고, 전단시험과 해석을 수행해 교차 검증했다. 상관계수는 모든 조건에 대해 0.97이상으로 실험과 해석결과 사이에 강한 상관관계가 있음을 확인했다. 전단시험과 해석의 전단면 형상 및 최대하중을 비교하여 도출한 유동응력 모델이 타당함을 보였다.

• 한국생활과학회지
• /
• 제22권1호
• /
• pp.131-140
• /
• 2013

Eco-friendly and health-functional clothing is now becoming the target of the worldwide hot trends. The purpose of this study is to develop an eco-friendly textiles to decrease environmental pollution and to be harmless for human health by investigating how the natural chorangak liquid treatment affects the changes of mechanical properties and the hand of silk fabrics according to different treatment conditions. Treatment was varied with various temperatures ($85^{\circ}C$, $90^{\circ}C$, $95^{\circ}C$) for 90 seconds after degumming. The results were as follows: 1) The natural chorangak liquid is the most effective at the ratio of glacial acid 200ml with eggshell 20g minimizing the time limit and sludge reduction. Its treatment of silk fabrics is optimized at $90^{\circ}C$ for 90 seconds with 25% conc. after degumming when considering tenacity and elongation. 2) After the treatment, tenacity and elongation of specimen are increased compared with those of degummed silk fabrics. 3) After analyzing the effect of the treatment on the characteristic values of basic mechanical properties of silk fabrics, mechanical properties (tensile, bending, shearing, compression, surface) are overall improved. The properties of thickness and weight are increased as well. 4) Based on the clear analysis on effects of the treatment on the mechanical properties and the hand of silk fabrics, the level of THV was enhanced from good to excellent. Therefore, chorangak liquid can be utilized satisfactorily as a new finishing agent for developing eco-friendly textiles.

• 한국기계가공학회지
• /
• 제13권3호
• /
• pp.6-14
• /
• 2014

Touch panels are widely used in the modern display industry as the cover glass of smart mobile phones and tablet PCs. Glass cutting machines are commonly used to cut the panels into their proper sizes. Vibration of these glass cutting machines is assumed to be the main factor leading to the creation of burrs, notches, cracks, scratches and chips on the cut surfaces, eventually causing defects of the cover glass. In this study, the vibrations of a glass cutting machine used for the shearing of cover glass components were analyzed through an experiment and a computer simulation. The structural properties leading to vibration were also analyzed in an effort to determine design alterations which can suppress these vibrations. Moreover, each design alteration was applied to a computer simulation model to determine the effect of different alteration on suppressing vibration. The results show that simple design alterations can substantially suppress vibrations of glass cutting machines.

• 한국의류학회지
• /
• 제18권5호
• /
• pp.595-601
• /
• 1994

This study was accomplished to investigate drape coefficient and wrinkle recovery of brushed fabrics according to treatment processes and brushing conditions. For this study, grey fabrics of blended ratio of polyester 65% : cotton 35% were bleached and dyed. These fabrics were then brushed 1, 3, 5 and 7 times. Drape coefficient and wrinkle recovery of brushed fabrics were measured by drape tester and shirley crease recovery tester respectively. The experimental results were analysed statistically to relate mechanical properties, handle, drapability, and wrinkle recovery 1) Drape coefficients of dyed fabric showed lower values and wrinkle recovery showed higher ones than those of bleached and dyed fabrics. Especially dyed fabric brushed 3 times showed good appearance and form stability. 2) Considering the blocked properties that contribute to the drape coefficient and wrinkle recovery of brushed fabrics, bending and shearing properties had a high degree of correlation with brushed fabrics, and 2HB/W showed a high positive correlation with drape coefficient and a high negative correlation with wrinkle recovery.

• 소성∙가공
• /
• 제23권1호
• /
• pp.23-28
• /
• 2014

The aspect ratio of a hole is defined as the ratio of the thickness to the diameter of the sheet metal. Most holes in the sheet metal industry are made by piercing. However, for thick sheets, which have an aspect ratio greater than 2, a machining process like drilling instead of piercing is usually used to make holes. In the current study, piercing, which is a shearing process, is evaluated to punch a hole with a high aspect ratio by using a newly designed die set-up. The piercing die was manufactured to prevent the punch from buckling and also to improve the alignment between the die components. An aluminum alloy sheet was selected for the experiments. The influence of several process parameters such as sheet thickness, clearance and stripping force were investigated. Experimentally, a hole with an aspect ratio of 5 was pierced. The resulting hole had a clean surface and the dimensional accuracy of pierced hole was considerably improved with decreasing clearance between punch and die. It is also shown that the larger penetration depth of the effective sheared surface can be achieved for high aspect ratio piercing relative to conventional piercing with a low aspect ratio.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.606-611
• /
• 2000

It has been noted that the low frequency absorption coefficient of a porous sample placed in a standing wave tube is affected by the nature of the sample's edge constraint. The edge constraint has the effect of stiffening the solid phase of the sample, which itself can be strongly coupled to the material's fluid phase, and hence the incident sound field, by viscous means at low frequencies. In recent work it has also been shown that such a circumferential constraint causes the low frequency transmission loss of a layer of fibrous material to approach a finite low frequency limit that is proportional to the flow resistance of the layer and which is substantially higher than that of an unconstrained sample of the same material. However, it was also found that the benefit of the circumferential edge constraint was reduced in a transitional frequency range by a shearing resonance of the sample. Here it will be shown that the effect of that resonance can be mitigated or eliminated by adding additional axial and radial constraints running through the sample. It will also be shown that the constraint effect can be modeled closely by using a finite element procedure based on the Biot poroelastic theory. Implications for low frequency barrier design are also discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.387-394
• /
• 2000

Theoretical and experimental study is conducted on the contact pressure distribution of a radial tire in motion under various camber angles. Tire construction is modelled by a spring bedded elastic ring, consisted of sidewall springs and a composite belt ring. The contact area is assumed to be a trapezoidal shape varying with camber angles and weighted load. The basic equation in a quasi-static form is derived for the deformation of a running belt with a constant velocity by the aid of Lagrange-Euler transformation. Galerkin's method and stepwise calculation are applied for solving the basic equation and the mechanical boundary condition along both sides of the contact belt part subjected to shearing forces transmitted from the sidewall spring. Experimental results on the contact pressure, measured by pressure sensors embedded in the surface of the drum tester, correspond well with the calculated ones for the test tire under various camber angles, running velocities and weighted loads. These results indicate that a buckling phenomenon of the contact belt in the widthwise direction occurs due to the effect of camber angle.

• 한국의류학회지
• /
• 제9권1호
• /
• pp.47-55
• /
• 1985

To determine the change of the mechanical properties of the wool/polyester blend fabrics in proportion to blend ratio, 10 mechanical properties were measured on 6 blend fabrics by KES-F system. Blend ratio on the 6 blend fabrics was increased by $20\%$, and the structure of the fabric were plain, 2/2 twill, respectively. And wearing performances in propoetion to blend ratio on the 6 blend fabrics were investigated. In this experiment. the following conclusions were obtained with the increase of blend ratio of polyester. 1) The values of WT, RT in tensile properties. tensile energy and elongation, and RC in compressional properties were decreased. 2) The values of B, 2HB in bending properties, 2HG. 2HG 5 in shearing properties were increased. 3) Putting on clothes, wearing performance was bad because crumbling of shape and wrinkle were easily made an appearance. Particularly it was remarkably bad as blend ratio of polyester was expressed $60\%$.