• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.1
• /
• pp.109-113
• /
• 2012

The LED failure rate greatly depends on the physical properties of packaging materials (epoxy). The glass transitions temperature (Tg) of the epoxy is one of the most important physical properties. Therefore, in the present study, various epoxies with high Tg were prepared and their failure shapes were analyzed. In addition, the failure shapes depending on the amount of epoxy and the wire bonding structure were measured. As a consequence, the lower failure rate was obtained with the smaller amount of epoxy. The safety of LED was improved with increasing the Tg of the epoxy.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1792-1797
• /
• 2007

This paper try to find root-cause of failure in a connector used in transmitting signals for throttle body control in automotives by analyzing possible failure causes and performing experiments to simulate the cable failure in field. The connector comprises fins, wires, and case moldings. The failure is due to degradation of initial clamping force required fixing fins and wires in the connector. Expansion and compression of the case molding material surrounding fins would cause the degradation. Investigations of strict initial claming force and control of thermal expansion property of the molding are required to prevent the failure.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.311-316
• /
• 2001

A failure probability model based on Von-Mises failure criterion and the standard normal probability function is proposed. The effects of varying boundary conditions such as internal fluid pressure, external soil, traffic loads, temperature change and corrosion on failure probability of the buried pipes are systematically investigated. To allow for the uncertainties of the design variables, a reliability analysis technique has been adopted; this also allows calculation of the relative contribution of the random variables and the sensitivity of the failure probability.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.507-510
• /
• 2001

Brittle failure mechanism has been well known as growth of initial micro-damage, that causes macro crack and failure in the end. Several precise criteria are suggested recently, based on experiments values in a whole load range. Among them, Mohr-Coulomb's criterion is used widely these days, but it has a big error compared with the real failure behavior since it does not show reciprocal actions of stresses. In this study, a new brittle failure criterion is proposed, which includes the effects of brittle damage evolution by taking a brittle damage parameter specifically. Comparisons between the proposed model and the previous ones are also given.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.204-213
• /
• 2003

A survey for finding corrosion examples was performed on the underground steel piles buried for 19 years in the area of iron and steel making factory near Young-il bay. A failure probability model, which can be used to check the reliability of the corrosive mechanical element, based on Von-Mises failure criterion and the standard normal probability function is proposed. The effects of varying boundary conditions such as temperature change, soil-friction, internal pressure, earthquake, loading of soil, traffic loads and corrosion on failure probability of the buried steel piles are systematically investigated. To allow for the uncertainties of the design variables, a reliability analysis technique has been adopted; this also allows calculation of the relative contribution of the random variables and the sensitivity of the failure probability.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2018.11a
• /
• pp.105-106
• /
• 2018

It is important to set up a reasonable failure criterion for cladding, because being able to determine the cladding integrity during transportation is essential for the evaluation of SNF transportation system. There are a few of measures which can be used as a failure criterion for cladding subjected to its specific failure mode. Therefore, to select and to use appropriate failure criterion measures, i.e. strain(UE), $K_{IC}$, and CSED would be a key in evaluating the cladding integrity during transportation with every aspects. In order to justify and quantify that criterion properly, various experiments for the mechanical properties of the claddings with different conditions shall be implemented, which data will enable to justify the failure criteria proposed.

• Elastomers and Composites
• /
• v.52 no.3
• /
• pp.167-172
• /
• 2017

Ultra-high performance (UHP) tires, for which demand has recently surged, are subject to severe strain conditions due to the low aspect ratio of their sidewalls. It is important to ensure sidewall material durability, since a sudden tire sidewall breakage during vehicle operation is likely to cause a major accident. In the automotive application of rubber parts, cracking is defined as a failure because when cracks occur, the mechanical properties of rubber change. According to Mars, Andre et al., strain and strain energy density (SED) are mainly used as a failure parameters and the SED is generally used as a fatigue damage parameter. In this study, the fatigue life curves of sidewall rubber of tires were determined by using the SED as fatigue damage parameter while the effect of aging on fatigue life was evaluated after obtaining the SED-Nf curves according to aging condition.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.445-450
• /
• 2003

This study was performed 10 develop the accelerated life test method using Weibull-IPL(Inverse Power Law) model for mechanical components. Weibull-IPL model is concerned with determining the assurance life with confidence level and the accelerated life test time From the relation of weibull distribution factors and confidence limit, the testing times on the no number of failure acceptance criteria arc determined. The mechanical components generally represent wear and fatigue characteristics as a failure mode. IPL based on the cumulative damage theory is applied effectively the mechanical components to reduce the testing time and to achieve the accelerating test conditions. As the actual application example, accelerated life test method of agricultural tractor transmission was described. Life distribution of agricultural tractor transmission was supposed to follow Weibull distribution and life test time was calculated under the conditions of average life (MTBF) 3,000 hours and 90% confidence level for one test sample. According to IPL, because test time call be shorten in case increase test load test time could be reduced by 482 hours when we put the load 1.1 times of rated load than 0.73 times of rated load that is equivalent load calculated by load spectrum of the agricultural tractor. This time, acceleration coefficient was 11.7.

• International Journal of Precision Engineering and Manufacturing
• /
• v.1 no.2
• /
• pp.55-60
• /
• 2000

A comparison of Riveted and bonded repairs, bearing and net tension failures, and Al 6061-T6 plates is presented. The results are then compared with previous papers about bonded repairs on different patch materials and shapes. Aluminum alloys, including Al 6061-T6, have a face-centered-cubic crystal structure. Under normal circumstances, these types of crystal structures do not exhibit cleavage fractures even at very low temperatures. In aluminum-base structures, the cracked plate structures are frequently repaired using mechanical fasteners-either rivets of bolts- even though patch-bonding techniques are applied to repair and reinforce the structure. Static test results indicate that the riveted repairs are affected by the position of the rivers. When using the same size of patch, the bonded repair technique is stronger; the rate of elongation is also increased. Form FEM analysis, it is revealed the origin of patch debonding in patch-bonded structures is the edge of the patch along to the tensile strength.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.139.1-139.1
• /
• 2005